Microview A Series Guide de l'utilisateur
aSERIES DVR04/DVR08 DIGITAL VIDEO RECORDER
Quick Operations Guide
UD.7L0202B1365B01
aSERIES DVR04 / DVR08 Digital Video Recorder · Quick Operations Guide
Thank you for purchasing our product. If there is any question or request, please do not hesitate to contact dealer.
This manual is applicable to MicroView DVR04 and DVR08 models.
DVR Pre-Installation
The DVR is highly advanced surveillance equipment that should be installed with care. Please take into
consideration the following precautionary steps before installation of the DVR.
1. Keep all liquids away from the DVR.
2. Install the DVR in a well-ventilated and dust-free area.
3. Ensure environmental conditions meet factory specifications.
4. Install a manufacturer recommended HDD.
DVR Installation
During the installation of the DVR:
1. Use brackets for rack mounting.
2. Ensure there is ample room for audio and video cables.
3. When installing cables, ensure that the bend radius of the cables are no less than five times than its diameter.
4. Allow at least 2cm (≈0.75-inch) of space between racks mounted devices.
5. Ensure the DVR is grounded.
6. Environmental temperature should be within the range of -10 ºC ~ 55 ºC, 14ºF ~ 131ºF.
7. Environmental humidity should be within the range of 10% ~ 90%.
Hard Disk Installation
Before you start:
Before installing a hard disk drive (HDD), please make sure the power is disconnected from the DVR. A
surveillance-class storage HDD is recommended for this installation.
Tools Required: Screwdriver.
To install a HDD on your DVR:
1. Remove the cover from the DVR by unfastening the screws on the back and side.
2. Install the HDD in the HDD rack using the provided screws. Fasten the screws on the bottom to fix the HDD.
3. Connect the HDD to the motherboard of the DVR with the included data cable, and connect the power cable
to the HDD.
1
aSERIES DVR04 / DVR08 Digital Video Recorder · Quick Operations Guide
4. Re-install the cover of the DVR and fasten screws.
Front Panel
Table 1 Description of Indicators
No.
Icon
Description
1 Indicator turns red when DVR is powered up.
2 Indicator lights in red when data is being read from or written to HDD.
3 Indicator blinks blue when network connection is functioning properly.
2
aSERIES DVR04 / DVR08 Digital Video Recorder · Quick Operations Guide
Rear Panel
The rear panel of DVR08 is shown below:
The DVR04 and DVR08 provides no HDMI interface.
Table 2 Description of Rear Panel
No. Item Description
1 VIDEO IN
BNC connector for analog video input.
2 VIDEO OUT BNC connector for video output.
3
HDMI
HDMI video output.
The DVR04 and DVR08 provides no HDMI interface.
4 VGA DB15 connector for VGA output. Display local video output and menu.
5 AUDIO IN RCA connector for audio input.
6 AUDIO OUT RCA connector for audio output.
7 LAN Interface RJ45 10M / 100M Ethernet interface.
8 USB Interface Connects USB mouse or USB flash memory devices.
9 12V 12VDC power supply.
10 GND Ground (needs to be connected when DVR starts up)
3
aSERIES DVR04 / DVR08 Digital Video Recorder · Quick Operations Guide
Specifications
The DVR04 and DVR08 provides no HDMI interface.
Model
DVR08
DVR08
Video/Audio
input
Video compression H.264
Video input
4-ch
8-ch
Video input interface
BNC (1.0 Vp-p, 75 Ω), PAL /NTSC self-adaptive
Audio compression
G.711u
Audio input
1-ch, RCA (2.0 Vp-p, 1 kΩ)
Two-way audio input 1-ch, RCA (2.0 Vp-p, 1 kΩ) (using the audio input)
Video/Audio
output
HDMI/VGA output
1-ch, resolution:
1080P: 1920×1080/60Hz, SXGA: 1280×1024/60Hz,
720P: 1280×720/60Hz, XGA: 1024×768/60Hz
CVBS output 1-ch, BNC (1.0 Vp-p, 75 Ω),
resolution: PAL: 704 × 576, NTSC: 704 × 480
Encoding resolution
WD1/4CIF/2CIF/CIF/QCIF
Frame rate 25 fps (P) / 30 fps (N)
Video bitrate
32 Kbps ~ 3072 Kbps, or user defined (Max. 3072 Kbps)
Audio output 1-ch, RCA (Linear, 1 kΩ)
Audio bitrate
64 Kbps
Dual-stream Support;
Sub-stream: CIF/QCIF @ 25 fps (P) / 30 fps (N)
Stream type Video, Video & Audio
Synchronous
playback
4-ch 8-ch
Hard disk SATA 1 SATA interface
Capacity
Up to 4TB capacity
External
interface
Network interface
1, RJ45 10M / 100M Ethernet interface
USB interface
2, USB 2.0
General
Power supply
12 VDC
Consumption
(without hard disk)
≤ 6 W ≤ 8 W
Working temperature
-10 ºC ~+55 ºC
Working humidity
10% ~ 90%
Dimensions
(W × D × H)
200 × 200 × 45 mm 200 × 200 × 45 mm
Weight
(without hard disk) ≤ 0.8 kg ≤ 1 kg
4
aSERIES DVR04 / DVR08 Digital Video Recorder · Quick Operations Guide
HDD Storage Calculation Chart
The following chart shows an estimation of storage space used based on recording at one channel for an hour at
a fixed bit rate.
Bit Rate
Storage Used
96Kbps
42 MB
128Kbps
56 MB
160Kbps
70 MB
192Kbps
84 MB
224Kbps
98 MB
256Kbps
112 MB
320Kbps
140 MB
384Kbps
168 MB
448Kbps
196 MB
512Kbps
225 MB
640Kbps
281 MB
768Kbps
337 MB
896Kbps
393 MB
1024Kbps
450 MB
1280Kbps
562 MB
1536Kbps
675 MB
1792Kbps
787 MB
2048Kbps
900 MB
3072Kbps
1350 MB
Please note that supplied values for storage space used is just for reference. Storage space used is
estimated by formulas and may have some deviation from actual value.
5
aSERIES DVR04 / DVR08 Digital Video Recorder · Quick Operations Guide
Menu Operation
Menu Structure
The menu structure of the DVR04 and DVR08 is shown as below:
The DVR04 and DVR08 provides no PTZ feature.
Startup and Shutdown
Proper startup and shutdown procedures are crucial to expanding the life of the DVR.
Before you start:
Check that the voltage of the extra power supply is the same with the device’s requirement, and the ground
connection is working properly.
Starting up the device:
Steps:
Check the power supply is plugged into an electrical outlet. It is HIGHLY recommended that an Uninterruptible
Power Supply (UPS) be used in conjunction with the device. The Power indicator LED should turn red indicating
that the unit begins to start up.
Shutting down the device:
Steps:
1. Enter the Shutdown menu.
Menu > Shutdown
6
aSERIES DVR04 / DVR08 Digital Video Recorder · Quick Operations Guide
2. Click the Shutdown button to enter the following dialog box:
3. Click the Yes button. The following message box pops up:
4. Disconnect the power supply of the device.
Using the Setup Wizard
The Setup Wizard can walk you through some important settings of the device. By default, the Setup Wizard starts
once the device has loaded.
Operating the Setup Wizard:
You can set the system language after the device is started. Click Apply to save the language settings.
7
aSERIES DVR04 / DVR08 Digital Video Recorder · Quick Operations Guide
1. Check the checkbox to enable Setup Wizard when device starts. Click Next to continue the setup wizard.
You can also click Cancel to exit the Setup Wizard, or use the Setup Wizard next time by leaving the “Start
wizard when device starts?” checkbox checked and exit.
2. Click Next button on the Wizard window to enter the Login window.
1) Enter the admin password. By default, the password is 12345.
2) To change the admin password, check the New Admin Password checkbox. Enter the new password
and confirm the password in the given fields.
3. Click the Next button to enter the Date and Time settings window.
Set the time zone, date format, system date and system time.
8
aSERIES DVR04 / DVR08 Digital Video Recorder · Quick Operations Guide
4. Click Next button which takes you back to the Network Setup Wizard window.
Set the network parameters, including the NIC type, IPv4 address, IPv4 subnet mask, default gateway, etc.
You can enable the DHCP to automatically obtain an IP address and other network settings from that
server.
5. Click Next button to enter the HDD Management window.
To initialize the HDD, click the Init button. Initialization removes all the data saved in the HDD.
9
Ce manuel convient aux modèles suivants
2
Table des matières
Autres manuels Microview DVR
