Microsemi PD-9001GC Manuel utilisateur
English
Deutsch
Microsemi PD-9001GC
User Guide
1-Port 802.3at Gigabit Midspan
Microsemi PD-9001GC
Benutzeranleitung
1-Port 802.3at Gigabit Midspan
C6626M 03/19
POE130-AT
1
Functions and Features
The PD-9001GC is a Power over Ethernet (PoE) Single Port Midspan/Injector that offers a super compact
and cost effective power solution for WLAN access points, network cameras and other IP terminal installations.
The PD-9001GC Power over Ethernet (PoE) Midspan/Injector is IEEE802.3at compliant, it adds 55V DC to wires
4,5,7,8 of a standard Ethernet cable in category 5 and above, and enables delivery of both data and power to the
IP terminal.
The PD-9001GC can be powered via universal AC input and can provide up to 30 Watts.
Main Features:
1-port PoE output
Guaranteed 30W
IEEE802.3at compliant
Super small dimensions
Universal AC input 100-240VAC
10/100/1000mbps pass-through data rates
Notice
It is Microsemi’s policy to improve its products as new technology, components, software, and firmware become
available. Microsemi, therefore, reserves the right to change specifications without prior notice.
Technical Support
If you encounter problems when installing or using this product, please consult the Microsemi website at:
http://www.Microsemi.com.
USA/Canada: +1-949-380-6245 POEsupport@microsemi.com
© 2017 Microsemi Corporation
2
English
Safety Information
Important Safety Information
This injector should be connected to PoE networks only, without routing to outside plant.
The PD-9001GC Ethernet and Terminal ports are shielded RJ45 data sockets. They can’t be used as Plain
Old Telephone Service (POTS) sockets. Only RJ45 data connectors can be connected to these sockets.
The PD-9001GC Ethernet and Terminal interfaces are qualified as Safety Extra-LowVoltage (SELV)
circuits according to IEC 60950-1. These interfaces can only be connected to SELV interfaces on other
equipment.
The power cord must be a three-conductor type (two current carrying conductors; one ground conductor)
terminated on one end by an IEC 60320 appliance coupler (for connection to the PoE Media Converter),
and on the other end by a plug containing a ground (earth) contact.
The power cord must be rated for a minimum of 250Vac RMS operation, with aminimum rated current
capacity of 5 amps (or a minimum wire gauge of 18 AWG (0.823mm2).
WARNINGS!
This Midspan should only be connectedto an IP device with which it was bought. Using PD-9001GC with
other IP devices can cause damage to IP device.
Follow basic electricity safety measures whenever connecting PD-9001GC to its power source.
A voltage mismatch can cause equipment damage and may pose a fire hazard. If voltage indicated on the
label is different from the power outlet voltage, do not connect PD-9001GC to this power outlet.
Do not use cross-over cable between the PD-9001GC output port and the load device.
Preliminary Steps
Read installation instructions before connecting the PD-9001GC to its power source.
There is no “on/off” switch; simply plug the PD-9001GC into an AC power source.
Verify that a PoE Ready Ethernet-compatible device is connected.
Do not cover PD-9001GC or block airflow to the unit with any foreign objects. Keep PD-9001GC away from
excessive heat and humidity and free from vibration and dust.
Ensure cable length from Ethernet network source to terminal does not exceed 100 meters (330 feet). This
Midspan is not a repeater and does not amplify Ethernet data signal.
Use a splitter if desired; ensure splitter is connected close to the terminal and not on the PD-9001GC!
PD-9001GC EMC Compliance:
FCC Part 15 class B and EN55032 class B
EN55024
VCCI
PD-9001GC Safety Compliance:
UL/cUL per 60950-1
GS Mark
3
Installing the Unit
1. Connect the PD-9001GC to an AC outlet (100-240VAC).
2. Connect the “DATA IN” jack (input) to the remote Ethernet network switch's Patch panel.
3. Connect the “PWR OUT” jack (output) to Terminal.
Terminal
Ethernet
Cat 5/5e cable
Ethernet Interface
Input (Ethernet): Ethernet 10/100/1000Base-T
RJ45 female socket
Output (Terminal): Ethernet 10/100/1000Base-
T, Plus 55VDC
RJ45 female socket, with DC voltage on wire
pairs, 4, 5 (+) & 7, 8 (-).
Indicators
Port LED
Indicated Behavior
Yellow On
Power is on (power is active)
Green On
A remote terminal is connected
Green Blinking
Overload state or short-circuit
4
English
Specifications
Environmental Specifications
Mode
Temperature
Humidity
Operating
-10 to 40°C
14 to 104°F
5 to 95% (non-condensing)
Storage
-20 to 70°C
-4 to 158°F
5 to 95% (non-condensing)
Electrical Specifications
Input Voltage
100-240 VAC (50/60Hz)
Maximal Input Current
1 Ampere
Available Output Power
30 Watts
Nominal Output Voltage
55 VDC
Physical Specifications
Unit weight
170 gr
Dimensions (W x H x L)
46 x 32 x 141 mm
5
Troubleshooting
Symptom
Corrective Steps
PD-9001GC
Midspan does not
power up
1. Verify that an approved power cord is used.
2. Verify that the voltage at the power inlet is between 100 and 240VAC.
3. Remove and re-apply power to the device and check the indicators during
power up sequence.
The Powered Device
(PD) doesn’t operate
1. Verify that the PD is designed for PoE operation according to IEEE802.3at
standard.
2. Verify that you are using a standard straight-wired four-pair cable (UTP/FTP
Category 5/5e/6).
3. Verify that the PD is connected to the PD-9001GC "Terminal" port.
4. If an external power splitter is in use, replace it with a known-good splitter.
5. Remove and re-apply power to the Midspan.
The end device
operates, but there is
no data link
1. Verify that you are using a standard straight-wired four-pair cable (UTP/FTP
Category 5/5e/6).
2. Verify that the Ethernet cable length is less than 100 meters from Ethernet
source to load/remote terminal.
3. Ensure that the input Ethernet cable is connected to the power injector’s
"Ethernet" port.
4. If an external power splitter is in use, replace it with a splitter known to be
good.
6
English
Recycling and Disposal
Disposal instructions for old products. The WEEE (Waste Electrical and Electronic Equipment) national
environmental initiatives has been put in place to ensure that products are recycled using best available treatment,
recovery and recycling techniques to ensure human health and high environmental protection. Your product is
designed and manufactured with high quality materials and components, which can be recycled and reused. Do not
dispose of your old product in your general household waste bin. Inform yourself about the local separate collection
system for electrical and electronic products marked by this symbol:
Use one of the following disposal options:
1. Dispose of the complete product (including its cables, plugs and accessories) in the designated WEEE
collection facilities.
2. If you purchase a replacement product, hand your complete old product back to the retailer. He should
accept it as required by the national WEEE legislation.
Ordering information:
Product Name: PD-9001GC
Part Number: PD-9001GC/AC
Description: 1-Port 30 Watts Midspan
© 2017 Microsemi Corporation.
Document P/N: 06-7124-160 REV A00
7
8
Deutsch
Microsemi PD-9001GC
Benutzeranleitung
1-Port 802.3at Gigabit Midspan
Funktionen und Features
PD-9001GC ist ein Power over Ethernet (PoE) Single Port Midspan/Injektor , der offers eine super
kompakte und kostensparende Lösung für WLAN Verbindungspunkte, Netzwerkkameras und andere IP
terminal Installationen bietet.
PD-9001GC Power over Ethernet (PoE) Midspan/Injektor ist IEEE802.3at conform fügt den Strängen
4,5,7,8 55V DC hinzu,mit einem Ethernet Kabel der Kategorie 5 und mehr, und ermöglicht die Zufuhr von
Daten mit Strom bis hin zum IP Terminal.
PD-9001GC kann mit AC Strom laufen und bis zu 30 Watt liefern .
Wesentliche Merkmale:
1-PORT PoE Ausgabe
Guarantiert 30W
IEEE802.3at konform
Super kleine Abmessungen
Universal AC input 100-240VAC
10/100/1000mbps Datentransport
Mitteilung
Es ist Microsemispolitik, seine Produkte als neue Technologie, Komponenten, Software und Firmwareverfügbar zu
verbessern. Microsemi behält sich das Recht vor, Änderungen ohne Ankündigung vorzunehmen.
Technische Betreuung
Wenn Sie Probleme bei der Installation oder der Verwendung dieses Produkts auftreten, konsultieren Sie bitte die
Microsemi Webseite unter
http://www.Microsemi.com
USA/Canada: +1-949-380-6245
POEsuppo[email protected]
© 2017 Microsemi Corporation
Table des matières
Langues :
Autres manuels Microsemi Adaptateur
