Micromark MM23052 Manuel

INSTALLATION & OPERATING INSTRUCTIONS

IIMMPPOORRTTAANNTT::PPLLEEAASSEERREEAADDTTHHEESSEEIINNSSTTRRUUCCTTIIOONNSSCCAARREEFFUULLLLYYBBEEFFOORREEAATTTTEEMMPPTTIINNGGTTOOIINNSSTTAALLLLTTHHIISSAALLAARRMMSSYYSSTTEEMM..

IIFFTTHHEESSYYSSTTEEMMIISSBBEEIINNGGIINNSSTTAALLLLEEDDBBYYAASSEECCUURRIITTYYIINNSSTTAALLLLEERROORREELLEECCTTRRIICCAALLEENNGGIINNEEEERR,,PPLLEEAASSEEEENNSSUURREETTHHAATTAA

CCOOPPYYOOFFTTHHEESSEEIINNSSTTRRUUCCTTIIOONNSSIISSGGIIVVEENNTTOOTTHHEECCUUSSTTOOMMEERRFFOORRRREETTEENNTTIIOONNAANNDDFFUUTTUURREERREEFFEERREENNCCEE..

This alarm system can provide valuable protection for your home and property if used properly. However, the system

cannot guarantee complete protection against burglary or robbery. Therefore, the manufacturer, distributor or supplier will

not be held responsible for any loss or damage which may occur.

2-ZONE EASYFIT INTRUDER ALARM

Check the contents of the

packaging:

• 2-zone control panel

• External siren

• Mains adaptor

• 1 PIR sensor

• 1 set of hardwired door

contacts

• 4 sticky pads

• Fixing screws

• Cable clips

• Wall plugs

• 30m of multi-core alarm

cable

• Fixing bracket

IMPORTANT

In certain areas of the country you are required by law to

notify the Police and Local Authority when you install an

Alarm System. Since the requirements of each Authority

differ, we suggest that you contact the Environmental Officer

of your local Borough for full information about your local

area‘s by-laws.

CCOONNTTEENNTTSS

Planning your system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Wiring diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Start with installing the control panel and siren . . . . . . . . . . . . .4

Fitting the PIRs and door contacts . . . . . . . . . . . . . . . . . . . . . . . .6

Wiring the control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Checking the system – Walk test . . . . . . . . . . . . . . . . . . . . . . . . .8

Total immobilisation of system . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Checking the system – Bell test mode . . . . . . . . . . . . . . . . . . . . .8

System entry time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

System exit time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Bell reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

To change password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

To arm the system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

To disarm the system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Chime zone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .back cover

KKIITTCCOONNTTEENNTTSS

Please note that this equipment and its components have NO user serviceable parts.

If you experience any difficulties call our Helpline.

MMIICCRROOMMAARRKKHHEELLPPLLIINNEETTEELL::0088770022441133002299

Monday to Friday (8.30am to 5pm)

www.micromark.co.uk

PPlleeaasseennoottee::BBeeffoorreeyyoouussttaarrttttooiinnssttaalllltthhiissMMiiccrroommaarrkkAAllaarrmm,,wweeaaddvviisseetthhaattyyoouusshhoouullddttaakkeeaaddeeqquuaatteessaaffeettyypprreeccaauuttiioonnss

wwhheennuussiinnggppoowweerrttoooollssaannddllaaddddeerrss..PPrrootteeccttyyoouurreeyyeesswwhheennddrriilllliinnggaannddnneevveerruusseeaapppplliiaanncceessiinnddaammppoorrwweettccoonnddiittiioonnss..

CONTROL PANEL

EXTERNAL SIREN

PIR SENSOR

MAINS ADAPTOR

ALARM CABLE

FIXING BRACKET

DOOR

CONTACTS

MMMM2233005522

ukpanels.com

WWHHAATTIISSAAZZOONNEE??

Throughout these instructions the term ZONE is used, meaning a defined area of protection. A zone can be one room, or any number of rooms,

connected to the same connection on the control panel. With this system there are 2 areas you can guard and a 24-hour anti-tamper guard.

The PIR detects movement of people or animals in the detection zone. Door contacts can be used to detect door or window entry in either zone. See the

diagram to help you plan your system.

IIMMPPOORRTTAANNTTPPOOIINNTTSSTTOO

CCOONNSSIIDDEERR

When planning your system and

before installation consider the

following points:

• TThhiissssyysstteemmiissddeessiiggnneeddttoouussee

oonnllyy11PPIIRRppeerrzzoonnee..

• Make zone 1 the Entry/Exit zone.

• Do not position PIRs facing

windows, in direct sunlight, above

a heat source such as radiator, or

in conservatories or draughty

areas.

• Where possible keep pets out of

areas protected by PIR sensors

when armed.

• Position control panel near a

power socket.

NNoottee::This alarm must only be

used when powered by the mains

adaptor, the internal battery

operates as a stabilizing back up

supply in the event of short periods

of power loss, and will not run the

system over a long period.

In the event of an activation during

a power loss period all of the zone

LEDs will illuminate when you

disarm the system. You will have to

reset the system using your

personal security code.

PLANNING YOUR SYSTEM ACCESSORIES

MMMM99445522

SSuurrffaacceemmaaggnneettiiccddoooorr

ccoonnttaaccttss..

2 terminal single reed.

White high impact

plastic. 4 fixing screws

and 2 adhesive pads

included.

MMMM2233004477

PPIIRRsseennssoorr

8 metre range,

3 terminal

connections

SSiirreennccoovveerrss

MMMM99445555

’C’ type. White

polypropylene

MMMM99446611

’C’ type. Yellow

polypropylene

MMMM99445533--44ccoorreeaallaarrmm

ccaabbllee

30m alarm cable. NNoottffoorr

uusseewwiitthhmmaaiinnssvvoollttaaggee..

White sheath, 4 core

(red/black/blue/yellow).

NNoottee::ddiissrreeggaarrddtthheebblluuee

wwiirreeoonntthhiisskkiitt..

MMMM99445544--3300ccaabblleecclliippss

3.5mm flat. White

Extra door contacts can be

used with and without PIRs.

Extra door contacts are

available as accessories.

SSIIRREENN

ZZOONNEE11

Use this as your entry/exit

zone. Door contacts.

ZZOONNEE22

PIR and/or door

contacts.

We suggest that outside

doors are protected by a

door contact, as 71% of

entries are made through a

door.

Home Office statistics, Jan.

2001.

CCOONNTTRROOLL

PPAANNEELL

ukpanels.com

WIRING DIAGRAMS

TYPICAL WIRING DIAGRAM SHOWING PIR IN ZONE 2 AND DOOR CONTACTS IN ZONE 1 (THE ENTRY/EXIT ZONE)

ZONE 2 ZONE 1

WIRING DIAGRAM SHOWING PIR AND DOOR CONTACTS

WIRED ON ONE CABLE RUN TO CONTROL PANEL IN THE

SAME ZONE

TRIM RED

WIRE BACK

INSULATION

AND COVER

WITH TAPE

TRIM RED WIRES BACK TO

INSULATION AND COVER

WITH TAPE

TERMINAL BLOCK

BLACK WIRES TWISTED

AND TAPED TOGETHER

BLACK WIRES TWISTED

AND TAPED TOGETHER

RED WIRES

TWISTED

AND

TAPED

TOGETHER

3-WAY

TERMINAL

BLOCK

FROM CONTROL

PANEL

FROM

CONTROL

PANEL

DOOR

CONTACTS

BATTERY

COMPARTMENT

SNAP CONNECTOR

DOOR CONTACTS

PIR

MAINS

ADAPTOR

PIR

SIREN

CONTROL PANEL

ANTI-TAMPER SWITCH

WIRING DIAGRAM SHOWING ADDING AN EXTRA

CONTACT TO AN EXISTING DOOR CONTACT

ZZOONNEE11

ZZOONNEE22

TRIM RED

WIRE BACK

INSULATION

AND COVER

WITH TAPE

ukpanels.com

START WITH INSTALLING THE CONTROL PANEL AND SIREN

Position the control panel near a mains socket and

within easy reach of the entry/exit door.

Before drilling holes, ensure that they are not near

hidden mains wiring and pipework.

When planning the wiring, avoid awkward cable runs

to the control panel, siren box, PIRs and door

contacts.

Install the control panel out of reach of young

children.

Mark for two vertical holes 60mm apart. Use a power drill with a no. 6 masonry drill bit, and

drill two holes 25mm deep. Insert the masonry plugs.

Mount the fixing bracket and secure with the fixing

screws.

456

2 3

60mm

ukpanels.com

Connect the connector from the control panel to the

connector on the end of the cable. Temporarily hang

the control panel on the bracket. Warning: Do not

power up the control panel yet.

Run the cable inside the property to the point of exit

where the the outside siren is to be installed. Drill a

hole through the inside wall to the outside and thread

through the cable to the outside. Use cable clips to

hold the cable near the exit hole.

Use a suitable platform to work from and use the

siren box as a template to mark the position for the

fixing screws. Drill holes 25mm deep and insert

masonry plugs.

Bring the cable to the position of the siren box and cut

the cable, allowing enough surplus for wiring into the

siren terminal block. Strip the wires and connect them

to the teminal block as shown.

Fix the siren to the wall with the 3 fixing screws and

wall plugs supplied. Start at the control panel and

secure the cable run with cable clips. Reserve some

clips for wiring the PIR and door contacts.

CHECK LIST

Have you planned the layout? 

Is the control panel near a power socket? 

Have you temporarily placed the control

panel on the fixing bracket? 

Are the connector plugs connected? 

Is the wiring to siren box completed? 

Has the wiring been secured with cable clips? 

wall

plugs

FFoolllloowwssaaffeettyypprreeccaauuttiioonnss

wwhheennuussiinnggllaaddddeerrss..

ukpanels.com

FITTING THE PIRs AND DOOR CONTACTS

Allow enough cable to reach the control panel.

Unscrew the fixing screw at the base of the PIR and

remove the front cover. Remove the knockout at the

base of the back casing. Strip the wires to bare the

ends.

Fit the door contact with the screws

with a gap of 5mm between the

leading edges. Fix the wireable

contact to the frame

Run the wiring to the door contacts

(see wiring diagrams). The picture

shows door contacts wired directly to

the control panel. Cut back the red

wire to the insulation and tape the

end.

Follow the same procedure for each of

the zones. At the control panel mark

the wwiirreesswwiitthhtthheezzoonneessffrroommwwhhiicchh

tthheeyyaarreeffrroomm..

Thread the stripped cable through and connect the

wires to the terminal block observing the colours.

Replace the cover and screw.

Use a sticky pad and secure the PIR to the mounting

surface. Run the cable back to the control panel

taking the shortest route and secure it with cable

clips.

CHECK LIST

Are PIRs wired correctly? 

Are the PIRs securely mounted? 

Is the gap between door contacts correct? 

Are the door contacts wired correctly? 

Are the wires marked with their zones? 

ukpanels.com

WIRING THE CONTROL PANEL

Ensure that the mains adaptor from the control panel

is unplugged. During all wiring, panel must be

switched off.

Plug the mains adaptor jack plug into the socket on

the back of the control panel.

Take the labelled wires and connect them into their

respective zones marked on the terminal block, using

the folllowing code for the wiring:

Connect the red wires into the terminal marked + or

red.

Connect the black wires into the terminal marked – or

black.

Connect the yellow wires into the terminal marked

yellow.

Tape down the anti-tamper spring before connecting the

back-up battery (when the battery is connected the panel

produces a bleep), otherwise as soon as the back-up

battery is connected in the control panel, the anti-tamper

sounds. If the siren does sound then:-

PPrreessss11112222to disarm.

Open the battery compartment cover and fit a Duracell

PP3 9 volt alkaline battery (not supplied). Replacement

batteries must be of a Duracell alkaline type. Make sure

that terminals on the connector are connected to the

correct terminals on the battery. NNeevveerruusseerreecchhaarrggeeaabbllee

bbaatttteerriieess..

PPLLEEAASSEENNOOTTEE::

TToommaaiinnttaaiinnooppttiimmuummsseeccuurriittyy,,tthheebbaatttteerryy

sshhoouullddbbeecchheecckkeeddrreegguullaarrllyyaannddrreenneewweeddeevveerryyyyeeaarr..

Check all wiring connections are tight in the terminal

block. Remove the tape from the anti-tamper spring

and place the control panel on the mounting bracket.

TThheeaallaarrmmwwiillllssoouunnddwwhheenntthheesspprriinnggiissrreelleeaasseedd,,

uunnttiilltthheeccoonnttrroollppaanneellmmaakkeessaaffiirrmmffiittaaggaaiinnsstttthhee

bbrraacckkeettddeepprreessssiinnggtthheeaannttii--ttaammppeerrsspprriinngg..

The anti-tamper spring will ‘click’ when it is

depressed.

PPrreessss11112222to silence the alarm, then pprreessss11112222to

reset the panel.

CHECK LIST

Is mains adaptor unplugged at wall socket? 

Have you plugged mains jack plug into

control panel? 

Are red, black and yellow wires connected

to the correct terminals in control panel? 

Is battery back-up in control panel? 

Is control panel firmly attached to the bracket? 

Is anti-tamper spring fully compressed? 

If additional cable is required, use 4-core alarm

cable (see accessories) and cut short the blue wire.

Anti-tamper spring

ukpanels.com

CHECKING THE SYSTEM – BELL TEST MODE

CHECKING THE SYSTEM – WALK TEST

In this mode you can test each zone without

the alarm sounding. The zones that you

enter or open will show on the control panel

by a flashing LED and a bleep sound.

PPrreessssPP11112222EEttooeenntteerrpprrooggrraammmmiinngg..

PPrreessssPP77EE

Open a door with a door contact fitted, or

enter an area where a PIR is fitted. The

control panel will bleep twice and the

Zone LED will illuminate.

Repeat the procedure for each zone to

check correct operation.

In this mode you can test the control panel

siren and the outside siren to hear them

working.

PPrreessssPP11112222EEttooeenntteerrpprrooggrraammmmiinngg..

PPrreessssPP00EEttooeennddtteesstt

The control panel returns to

programming mode with flashing

SYSTEM ARMED LED on Zone 1 and 2.

PPrreessssPP00EEaaggaaiinnttooeexxiittpprrooggrraammmmiinngg..

PPrreessssPP66EE

Zones 1 and 2 LEDs will flash with the control

panel siren and the outside siren sounding

for 15 seconds.

PPrreessssPP00EEttooeennddtteesstt

The internal buzzer will temporarily sound a

constant tone for 3 seconds.

The control panel returns to programming

mode with flashing STATUS LED.

PPrreessssPP00EEaaggaaiinnttooeexxiittpprrooggrraammmmiinngg..

123

Plug the adaptor from the control panel

into the mains socket and switch on.

The power LED on the control panel will

light showing that programming can

begin.

If for any reason the sirens sound,

pprreessss11112222to disarm.

TOTAL IMMOBILISATION

OF SYSTEM

Should it be necessary to totally

immobilise the system in the alarmed

state (e.g. forgotten you password):

aa..Unplug from mains.

bb..Remove control panel from fixing

bracket, and remove the back-up battery.

If you are unable to get the system to

reset, contact the Micromark Helpline.

TThheessttaattuussoofftthheerreeddPPOOWWEERRLLEEDDoonntthhee

ccoonnttrroollppaanneelliissaassffoolllloowwss::

OONNPower on

OOFFFFNo transformer supply

TThheemmeeaanniinnggoofftthheerreeddSSTTAATTUUSSLLEEDDoonn

tthheeccoonnttrroollppaanneelliissaassffoolllloowwss::

OONN24-hr fault, or reset

required

OOFFFFNormal

FFLLAASSHHIINNGGProgram mode

CONTROL PANEL STATUS

ukpanels.com

SYSTEM ENTRY TIME

Then PPrreessssPP22EEand within 5

seconds your choice.

((IIffyyoouuddoonnoottddeecciiddeewwiitthhiinn55

sseeccoonnddss,,tthhrreeeesshhoorrttbblleeeeppss

wwiillllbbeehheeaarrdd,,aannddyyoouuwwiillll

hhaavveettooeenntteerrPP22EEaannddssttaarrtt

aaggaaiinn..))

Then PPrreessssPP00EEto exit

programming.

123 4

Entry time is the period

of time allowed for you

to enter and disarm the

system with the

password (factory set to

1122), before the sirens

sound.

The entry time is set by

the factory to 20

seconds but this can be

changed from a choice

of 7 other entry times to

suit you.

If for any reason the

sirens sound, pprreessss

11112222to disarm.

PPrreessss33EEwhich is the

program for 40 seconds.

If entered correctly, a

continuous bleep will be

heard for 2 seconds.

For example, to change the

entry time to 40 seconds (see

choices in Table):

PPrreessssPP11112222EEttooeenntteerr

pprrooggrraammmmiinngg..

SYSTEM EXIT TIME

Exit time is the period of

time allowed for you to

exit after arming the

system with the

password, before the

sirens sound.

The exit time is set by

the factory to 15

seconds but this can be

changed from a choice

of 7 other exit times to

suit you.

If for any reason the

sirens sound, pprreessss

11112222to disarm.

For example, to change the

exit time to 60 seconds (see

choices in Table):

PPrreessssPP11112222EEttooeenntteerr

pprrooggrraammmmiinngg..

Then PPrreessssPP33EEand within 5

seconds your choice.

((IIffyyoouuddoonnoottddeecciiddeewwiitthhiinn55

sseeccoonnddss,,tthhrreeeesshhoorrttbblleeeeppss

wwiillllbbeehheeaarrdd,,aannddyyoouuwwiillll

hhaavveettooeenntteerrPP33EEaaggaaiinn..))

PPrreessss44EEwhich is the

program for 60 seconds.

If entered correctly, a

continuous bleep will be

heard for 2 seconds.

Then PPrreessssPP00EEto exit

programming.

Example:

To choose other entry times:

11EE10 seconds

00EE15 seconds

22EE20 seconds

33EE40 seconds

44EE60 seconds

55EE90 seconds

66EE120 seconds

77EE240 seconds

To choose other exit times:

11EE10 seconds

00EE15 seconds

22EE20 seconds

33EE40 seconds

44EE60 seconds

55EE90 seconds

66EE120 seconds

77EE240 seconds

ukpanels.com

BELL RESET

Then PPrreessssPP44EEand within 5

seconds your choice.

((IIffyyoouuddoonnoottddeecciiddeewwiitthhiinn55

sseeccoonnddss,,tthhrreeeesshhoorrttbblleeeeppss

wwiillllbbeehheeaarrddaannddyyoouuwwiillll

hhaavveettooeenntteerrPP44EEaannddssttaarrtt

aaggaaiinn..))

Then PPrreessssPP00EEttooeexxiitt

pprrooggrraammmmiinngg..

TO CHANGE PASSWORD

The panel comes factory set to a standard 4-digit password 11112222. This password code is the signal by

which the panel recognises a legitimate user, we recommend that you change this code to a 4-digit

password code of your own choosing. Each member of your family or household will have to know this

code and how to use it. To change the factory set code:

TTOOCCHHAANNGGEETTHHEEFFAACCTTOORRYYSSEETTCCOODDEE::

PPrreessssPP11112222EEttoo

eenntteerrpprrooggrraammiinngg..

????

SETTING UP CHECK LIST

Have you done the walk test 

Have you done the bell test? 

Have you set your preferred entry time? 

Have you set your preferred exit time? 

Have you set your preferred bell reset time? 

Have you changed your password? 

After activation of the alarm system, the

external siren will stop after the

programmed time, but the internal siren

will beep slowly until the password has

been entered.

The bell reset time is set by the factory to

10 minutes but this can be changed from

a choice of 3 other times to suit you.

The bell reset test mode enables you to

re-program the length of time you wish

the siren to sound after it has been

activated. The legal maximum time under

current legislation is 20 minutes.

If for any reason the sirens sound,

pprreessss11112222to disarm.

For example, to change the

bell reset to 15 minutes (see

choices in Table):

PPrreessssPP11112222EEttooeenntteerr

pprrooggrraammmmiinngg..

PPrreessss33EEwhich is the

program for 15 minutes.

If entered correctly, a

continuous bleep will be

heard for 2 seconds.

PPrreessssPP11EE..

YYOOUUMMUUSSTTNNOOWWUUSSEETTHHEENNEEWWPPAASSSSWWOORRDDFFOORRAALLLLAACCTTIIOONNSS..

You have 10 seconds

to enter the new 4-

digit password plus EE.

After the keys are

pressed an

acceptance tone of 2

seconds duration will

be heard and then

reset back to zones 1

and 2 with flashing

LEDs.

PPrreessssPP00EEttooeexxiitt

pprrooggrraammmmiinngg..

Should the system

lose power, the

control panel

reverts to the

factory default

settings.

Example:

Choices are:

11EE5 minutes

22EE10 minutes

33EE15 minutes

44EE20 minutes

55EE1 minute

66EE2 minutes

77EE3 minutes

88EE4 minutes

ukpanels.com

Table des matières

Autres manuels Micromark Système de sécurité

Micromark

Micromark MM23292 Manuel

Micromark

Micromark MM23207 Manuel

Manuels Système de sécurité populaires d'autres marques

Inner Range

Inner Range Concept 2000 Manuel utilisateur

Climax

Climax Mobile Lite R32 Instructions de montage

CADDX

CADDX NX-6 Manuel utilisateur

FBII

FBII XL-31 Series Manuel utilisateur

Johnson Controls

Johnson Controls PENN Connected PC10 Manuel utilisateur

Aeotec

Aeotec Siren Gen5 Manuel utilisateur

Blaupunkt

Blaupunkt SA 2700 Manuel utilisateur

IDEAL

IDEAL Accenta Manuel du propriétaire

AJAX

AJAX DoubleButton Manuel utilisateur

Swann

Swann SW-P-MC2 Manuel utilisateur

Ecolink

Ecolink Siren+Chime Manuel utilisateur

Digital Monitoring Products

Digital Monitoring Products XR150 Manuel utilisateur

EDM

EDM Solution 6+6 Wireless-AE Manuel utilisateur

Highway Safety Group

Highway Safety Group EA401 Manuel utilisateur

Siren

Siren LED GSM Manuel utilisateur

Detection Systems

Detection Systems 7090i Instructions de montage

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Manuel utilisateur

Siemens

Siemens FDM273 Manuel utilisateur