Microh Firefly RGB Manuel utilisateur

1



TABLE OF CONTENTS

1. INTRODUCTION AND UNPACKING 1

2. SAFTEY INSTRUCTIONS 1-2

3. OPERATION INSTRUCTIONS 2-3

4. MOUNTING AND INSTALLATION 3-4

5. DMX-512 CONTROL CONNECTIONS 5

6. MENU NAVIGATION 5

7. DMX CHANNELS 6

8. KEY FEATURES 7

9. TECHNICAL SPECIFICATIONS 7

10. MAINTENANCE AND CLEANING 8

1. INTRODUCTION AND UNPACKING

Thank you for purchasing the MICROH FIREFLY RGB laser system. For your own safety and knowledge, please read this manual

before installing or operating the device. This manual covers the important information on installation and applications. Please install

and operate the fixture according to instructions. Meanwhile, please keep this manual for future reference.

The MICROH FIREFLY RGB laser is made of a new type of high temperature cast aluminum casing. The fixture is designed and

manufactured strictly following CE standards, complying with international standard DMX512 protocol. This fixture is applicable but

not limited to large-scale live performances, theater, studio, nightclubs and discos.

The MICROH FIREFLY RGB laser system uses 3 coloured laser diodes that are carefully aligned with the internal scan mirrors.

Please carefully unpack it when you receive the fixture and check if it was damaged during the transportation. And please check

whether the following items are included inside the box:

Fixture – One Power Cord – One Bracket Set – One User Manual – One

2. Safety Instructions

This device has left the factory in perfect condition. In order to maintain this condition and to ensure safe operation, it is absolutely

necessary for the user to follow the safety instructions and warning notes written in this user manual.

If the device has been exposed to temperature changes, do not switch it on immediately. The arising condensation could damage

the device. Leave the device switched off until it has reached room temperature, and is dry.

This device falls under protection-class I, therefore it is essential that the device be grounded. The electrical connection must be

carried out by a qualified technician.

The device should only be used with rate voltage and frequency. Make sure that the available voltage is not higher than 120V as

stated at the end of this manual.

2



Make sure the power cord is never crimped or damaged in any way, as this could cause shock and damage. If your power cord is

damaged in any way, please purchase a new cable from your local MICROH dealer. Always disconnect power, when the device is

not in use or before cleaning it. Never pull out the plug by tugging the power cord.

During initial start-up, some smoke or smell may arise. This is a normal process, and does not necessarily mean that the device is

defective. It should decrease gradually. Please do not project the beam onto combustible substances.

Fixtures cannot be installed on or near combustible substances. Keep more than 50cm distance from wall for proper ventilation and

air flow. If your fixture is or has become damaged in any way, it shall be exclusively replaced or repaired by the manufacturer to

avoid any hazard.



A Class 3B laser is hazardous to eyes, if exposed directly. Diffused reflections such as from paper or other matte

surfaces are not as harmful.



3.OPERATIONINSTRUCTIONS

- Do not turn on the fixture if it has been through severe temperature differences. Damage may occur to the fixture. Wait

until unit is at room temperature to operate.

- The unit should be protected from any tremor or agitation during transport.

- Do not expose the fixture in any excessive heat, moisture or any environment with too much dust when installing. Do not

lay any power cables on the floor. It may cause electronic shock or damage to persons or equipment.

- Make sure to attach the safety chain and ensure the screws are properly screwed in when installing the fixture.

- Make sure the lens is in good condition. It is recommended to replace the unit if there are any damages or severe

scratches.

- Make sure the fixture is operated and installed by qualified personnel.

- Keep the original packaging in case of defective product.

- Any non-manufacturer additions, modifications or changes in any way will void all warranty.

- Please do not attempt to open unit. It is only to be serviced by an authorized technician. If this occurs, or is apparent, the

warranty will be voided.

- The fixture’s warranty will be voided if there are any malfunctions from not following the user manual or any illegal

operation (shock short circuit, electronic shock, lamp broke, etc.)

3



DIPSWITCH CHART

DIP SWITCH CHART

X = OFF 1=ON FUNCTION

1 2 3 4 5 6 7 8 9 10

X X X X X X X X X X Sound Active

1 X X X X X X X X X Auto (Beam)

1 1 X X X X X X X X Auto (Animation)

X X 1 X X X X X X X Slave

1 SET DMX ADDRESS FOR DMX MODE 1 DMX

DMX MODE

- Before using the DMX512 controller, the channel address should be set. It can be set 001~511.Every binary address

switch has a digital number. Please refer to chart below.

No. Digital No. No. Digital No.

1st 1 6th 32

2nd 2 7th 64

3rd 4 8th 128

4th 8 9th 256

5th 16 10th Function switch

ILDA (PC CONTROL) MODE

- To run the FIREFLY RGB in IDLA mode or (PC CONTROL MODE) simply connect your ILDA signal cable to the DB25

jack located on the rear of the unit, and the unit will automatically recognize. NOTE: when ILDA is connected, it

supersedes all modes.

4. MOUNTING AND INSTALLATION

Caution: For added protection, mount the fixtures in areas outside walking paths, seating areas, or in areas were the fixture might

be reached by unauthorized personnel. Before mounting the fixture to any surface, make sure that the installation area can hold a

minimum point load of 10 times the device’s weight. Fixture installation must always be secured with a secondary safety attachment,

such as an appropriate safety cable. Never stand directly below the device when mounting, removing, or servicing the fixture.

Whether installing inverted on a truss or ceiling, or set on a flat level surface (see illustration below). Be sure this fixture is kept at

least 0.5m (1.5 ft) away from any flammable materials (decoration etc.). Always use and install the supplied safety cable as a safety

measure to prevent accidental damage and/or injury in the event the clamp fails.

4



Mounting Points: Overhead mounting requires extensive experience, including calculating working load limits. A knowledge of the

installation material being used, and periodic safety inspection of all installation material and the fixture are all imperative and should

only be performed by a qualified technician. Improper installation can result in bodily injury and damage.

Be sure to complete all rigging and installation procedures before connecting the main power cord to the appropriate wall outlet.

Regardless of the rigging option you choose for your MICROH FIREFLY RGB laser fixture, always be sure to secure your fixture

with a safety cable. The fixture provides a built-in rigging point for a safety cable on the hanging bracket as illustrated above. Be

sure to only use the designated rigging point for the safety cable and never secure a safety cable to a carrying handle. Please see

picture below.

5



5. DMX-512 CONTROL CONNECTIONS

This fixture complies with international USITT DMX standards and can be used with either a 3 pin or 5 pin DMX connector. Plug in

the provided 3 pin XLR cable to the female 3-pin XLR output of your controller and the other side to the male 3-pin XLR input of the

MICROH FIREFLY RGB. To connect the units to DMX, you must daisy chain the fixtures together as referred in the diagram below.

Always end your DMX-512 connection with a DMX terminator.



For installations where the DMX cable has to run a long distance, or is in an electrically noisy environment, it is recommended to

use a DMX terminator. This helps in preventing corruption of the digital control signal by electrical noise. The DMX terminator is

simply an XLR plug with a 120 Ωresistor connected between pins 2 and 3,which is then plugged into the output XLR socket of the

last fixture in the chain. Please see illustrations below.

PIN 3

PIN 2

120



6. MENU NAVIGATION



Press ‘MODE’ button for following functions:

‘Audi’ Sound Active

‘Auto’ Auto

‘dxxx’ DMX (‘xxx’ is the address code. Press ‘UP’ or ’DOWN’ to select desired address)

‘SLAV’ Slave (Slave machine will do the same effect as the mater fixture)

‘XXXX’ Total Run Time (Shows how long the laser has run in total)

‘ENTER’ Press after selecting mode to confirm

6



7. DMX CHANNELS

Channel No DMX Address Content

Channel 1 Control mode

0 - 49 Sound Active Control

50 - 99 Auto (Beam)

100-149 Auto (Animation)

150 - 255 Manual

Channel 2

Color select

0 No Function

1 - 255 Color Change

Channel 3 Pattern select 0 - 255 Patterns

Channel 4 Vertical

Movement

0 - 127 Manual

128 - 191 Down to Up Speed

192 - 255 Up to Down Speed

Channel 5 Horizontal

Movement

1 - 127 Manual

128 - 191 Right to Left Movement

192 - 255 Left to Right Movement

Channel 6 Vertical

Rotation 0 - 255 Slow to Fast Speed

Channel 7 Horizontal

Rotation 0 - 255 Slow to Fast Speed

Channel 8 Rotation

0 - 127 Manual

128 - 191 Counter Clockwise Rotation

192 - 255 Clockwise Rotation

Channel 9 Zoom

0 Static

1 - 85 Small to Big

86 - 170 Big to Small

171 - 255 Auto Zoom

Channel 10 Pattern Size

0 Default Size

1 - 255 Small to Big

Channel 11 Spot and Line 0 - 255 Line to Spot

Channel 12 Twinkle speed 0 – 255 Slow to Fast

7



8. KEY FEATURES

- RGB Colour Mixing DPSS Diodes (Red650nm, Green 532nm, Blue450nm)

- Pre-Programmed Beam Shows and Animations (Total of 128)

- Controllable via DMX (3 Pin XLR)

- IDLA Input for PC Control

- High Speed Quality 20-25K Scan Motors (Max 20,000 pps)

- Eyebolt for Safety Support, Will Support 10 times Weight of Fixture

- Air Cooled

- 700 mW Total Laser Output (R300mw + G100mw + B300mw)

- DMX, ILDA, Sound Active, Auto, Master/Slave Run Modes

-12 DMX Channels

9. TECHNICAL SPECIFICATIONS

MODEL: FIREFLY RGB

LASER DIODE: DPSS, Red650nm, Green 532nm, Blue450nm

SCANNER: 20-25 Kpps

SCANNING ANGLE: ± 30°

COOLING SYSTEM: Fan

MAX RUN TIME: Approximately 4 Hours

WARM-UP TIME: < 15 Minutes

WORKING TEMPERATURE: 10° ~ 35° C

VOLTAGE: 120VAC 60Hz

FUSE: 120VAC 1A

DIMENSIONS: 13.50” x 9.72” x 4.09” / 343 x 247 x 104 mm

BOX DIMENSIONS: 17.91” x 12.2” x 8.46” / 455 x 310 x 215 mm

NET WEIGHT: 7.75 lbs / 3.52 kg

GROSS WEIGHT: 10.5 lbs / 4.76kg

WARRANTY: 2 Year Limited Warranty. The Laser diodes are covered under a 6 month replacement warranty. 

8



10. MAINTENANCE AND CLEANING

The following points have to be considered during the inspection:

1) All screws for installing the device or parts of the device must be tightly connected, and must not be corroded.

2) There must not be any deformations on the housing, colour lenses, fixations or installation spots (ceiling, suspension, trussing).

3) Mechanically moved parts must not show any traces of wearing and must not rotate with unbalances.

4）The electric power supply cables must not show any damage, material fatigue or sediments.

Further instructions depending on the installation spot and usage must be handled by a skilled installer or technician. Any safety

issues must be resolved.

In order to keep the fixture in good condition and extend the life, we suggest regular cleaning to the fixture.

1) Clean the inside and outside lens each week to avoid the light output from darkening due to accumulation of dust, dirt, etc.

2) Clean the fan each week.

3) A detailed electrical check by approved technician every three months is advised. Ensure the circuit contacts are in good

condition, and prevent from overheating.

We recommend a frequent cleaning of the device. Please use a moist, lint- free cloth. Never use alcohol or solvents.

There are no serviceable parts inside the device. Please refer to the instructions under “Installation instructions”.

Should you need any spare parts, please order genuine MICROH parts from your local dealer.

IF YOU SHOULD EXPERIENCE ANY PROBLEMS OR ISSUES PLEASE CONTACT MICROH PROFESSIONAL PRODUCTS BY

EMAIL AT [email protected]m

In the event that your unit is defective in any way, please contact your local dealer to obtain an RA number for service

repair.

DISCLAIMER – MICROH believes that the information contained within this user manual is accurate. However, Microh is

not responsible for any error or addendums to this manual. If you have any comments or general suggestions on how this

manual can be improved please contact info@microhpro.com. Thank you.

Table des matières

Autres manuels Microh Équipement d'éclairage

Microh

Microh RIO ELEMENT518 Manuel utilisateur

Microh

Microh LED SLIM P64 Manuel utilisateur

Microh

Microh NEPTUNE GB Manuel utilisateur

Microh

Microh Profile Spot PZM Manuel utilisateur

Microh

Microh DUO BEAM/RG Manuel utilisateur

Microh

Microh Ultra Wash 1200 Manuel utilisateur

Microh

Microh LEDBAR RGB Manuel utilisateur

Microh

Microh Monsoon FX GB Manuel utilisateur

Microh

Microh LED MAX PAR Manuel utilisateur

Microh

Microh Led Vixion Quad Manuel utilisateur

Microh

Microh LED PHANTOM ZM400 Manuel utilisateur

Microh

Microh LED Razor45 Manuel utilisateur

Microh

Microh Led Max Zoom Tri Manuel utilisateur

Microh

Microh QUADBEAM Manuel utilisateur

Microh

Microh ARENA ULTRA WASH ii Manuel utilisateur

Microh

Microh MONSOON FX Manuel utilisateur

Microh

Microh LED Trickster Manuel utilisateur

Microh

Microh Ultra Sport 1200 Manuel utilisateur

Microh

Microh ARENA PROFILE SPOT Manuel utilisateur

Microh

Microh Asteroid RGB Manuel utilisateur

Microh

Microh Blazer 100 Manuel utilisateur

Microh

Microh Ultra Spot 700 Manuel utilisateur

Microh

Microh UV BRICK16 Manuel utilisateur

Microh

Microh LEDPRO64RGBW Manuel utilisateur

Manuels Équipement d'éclairage populaires d'autres marques

Brizo

Brizo 8SP-MU-4 Manuel utilisateur

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manuel utilisateur

IKEA

IKEA BJÖRKSPIREA Manuel utilisateur

Laserworld

Laserworld Evolution Series ES-400RGB Manuel utilisateur

Alien

Alien RG STAR Manuel utilisateur

EuroLite

EuroLite LED B-40 Manuel utilisateur

Qazqa

Qazqa Suplux SL 3 Black 103062 Manuel utilisateur

Commercial Electric

Commercial Electric 54568141 Manuel utilisateur

CREE LIGHTING

CREE LIGHTING 304 Series Manuel utilisateur

Goobay

Goobay 49867 Manuel utilisateur

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manuel utilisateur

Alkalite

Alkalite Krypton KT-81 Manuel utilisateur

Clas Ohlson

Clas Ohlson GU10 Manuel utilisateur

DTS

DTS DELTA 10 F Manuel utilisateur

ring

ring Solar Steplight Manuel utilisateur

One Stop Gardens

One Stop Gardens 57696 Instructions de montage

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manuel utilisateur

SIREM

SIREM Swimeo A2 Manuel utilisateur