MicroBoards Technology Micro Orbit Manuel utilisateur

The system will automatically load the

new firmware. The two LED’s on the

front of the unit will flash. The system

will also make beeping noises.

Error Conditions

If the system cannot read a master disc

or fails to write to a blank disc, the

system will stop operation and produce a

constant beeping noise. This error

condition will occur if it detects a bad

disc in either TEST or COPY mode.

When a defective disc is detected, the

recorder drive tray will open and the disc

will be lifted out of the tray.

The tray will then close and the system

will produce the constant beeping noise.

Remove the completed discs from the

output bin and press the button. This

will drop the failed disc.

Once the disc is dropped, the system will

be ready to start another job. If you need

to complete more copies, you will need

to place the master disc back on the

spindle and have it read into the hard

drive again.

Firmware Update

If it is necessary to update the system

program in the Micro Orbit duplicator,

please follow these steps.

Power on the Micro Orbit system and

wait for it to complete initializing. The

green LED will be on solid when the

system is ready.

Remove the CD spindle and the output

bin from the system.

Press and hold the button on the front of

the unit for approximately 5 seconds.

The system will beep twice. Release the

button.

The drive tray will now open. Place the

firmware CD into the drive tray and

close it.

Once the firmware is loaded, the drive

tray will open and the system will beep.

Remove the firmware CD and close the

drive tray.

Turn power off, wait 5 seconds and then

turn power back on.

The system is now ready to use, with the

new firmware installed.

Support Information

For technical questions or support

issues, please contact Microboards

Technology technical support at PH:

952-556-1639, FAX: 952-556-1628, by

email at [email protected] or

the web http://www.microboards.com.

8150 Mallory Court

Chanhassen, MN 55317

Tel: (Support) 952-556-1639

Tel: (Sales) 952-556-1600

Fax: 952-556-1628

Support: [email protected]

Web Site: http://www.microboards.com

Version 1.2

Micro Orbit

Operation Manua

Overview

The Micro Orbit is a 50-disc, batch-load duplicator. It has only one button to operate

its simulation and copy modes. Masters are read into the internal hard drive through

the recorder, eliminating the need for a separate reader. Masters and blanks can be

interleaved on the input spindle to allow for batch mode processing. When the

system recognizes a new master, it reads it into the hard drive then ejects the maste

into the output bin and starts recording the next series of blanks until it runs out o

media or recognizes a new master in the drive.

The system can come configured with a 40x CD Recorder or a 4x DVD-R recorder.

The DVD system can record CD or DVD masters.

System Setup

Using the Micro Orbit CD system is very easy. Plug in power, turn on your system,

load the system with media and press a button. When the system is turned on, the

green LED will flash, as it goes through the initialization stage. When initialization is

complete, the green LED will be on solid. Press the button once to start COPY mode

or press the button 5 times, to start TEST mode. Both modes are explained in more

details later in this document.

This process will continue until the

system runs out of discs.

This process will continue until the

system runs out of discs.

The first blank disc will now be loaded

into the recorder and the system will

simulate writing to that disc. Once

completed, the disc will be ejected and

placed in the output bin.

The first disc will be loaded into the

recorder and the information will be

copied to the internal hard drive.

Load the spindle with your discs, as

described earlier. To run the system in

COPY mode, press the button on the

front of the unit 1 time.

The first blank disc will now be loaded

into the recorder and the system will

write to that disc. Once completed, the

disc will be ejected and placed in the

output bin.

The system will beep once the job is

complete. Press the button once and the

green LED will become solid.

Once this is complete, the master disc

will be removed from the recorder and

placed in the output bin.

Once this is complete, the master disc

will be removed from the recorder and

placed in the output bin.

Loading Discs

To load the discs, remove the disc

spindle and turn it upside down.

Twist the end of the spindle, so the

bottom section is flush with the rest of

the spindle.

Load the discs in upside down, so the

recording side of the disc is up. Load the

blank discs first, then the master disc

last.

If you wish to copy multiple masters,

load the number of blank discs you want

to copy, then your master disc. Then

load the next batch of blanks and the

next master disc. You can repeat this

process until you have 50 discs loaded

on the spindle. With the DVD-R system,

you can mix in CD and DVD masters,

but your blank discs must be the same as

the master. You cannot copy CD

masters to DVD-R discs or DVD masters

to CD-R discs. Remember, 50 discs is

the maximum number of discs the

system will hold.

Once the discs are loaded on the spindle,

rotate the end of the spindle, so that the

bottom of the shaft is offset to one side.

Place your hand between the spindle top

and black metal plate at the base of the

spindle. Lift the disc stack up until the

top disc is resting against the offset post.

Then turn over the spindle. The discs

will be held in place by the offset portion

at the bottom of the spindle.

Place the spindle in the front of the

duplicator, aligning the arrow with the

front of the duplicator. The spindle will

lock into place and is ready for use.

System Modes

The Mini Orbit system can run in two

modes, TEST and COPY.

Once you start in one mode, you must

cycle power to switch to the other mode.

For example, if you run in TEST mode

first, to test your discs and then want to

switch to COPY mode, you must cycle

power to the system.

TEST mode will simulate writing to the

blank discs. This mode is used for

testing your master discs and blank discs

without the risk of wasting your blanks.

To enter TEST mode, press the button 5

times. The system will make a series of

beeps and then start the duplication

process. Again, this mode will not write

any data to the blank discs.

Write Mode will record the information

from your master disc to the blank discs.

To enter Write mode, press the button

once. The system will beep once and the

green led will start blinking. The

duplication process will begin by loading

your master disc to the internal hard

drive and then copying the information

to the blank discs.

Running in TEST Mode

TEST mode can be used to make sure

your master disc is readable and your

blank discs are recordable, without

wasting any blank discs.

Load the spindle with your discs, as

described earlier. To run the system in

TEST mode, press the button on the

front of the unit 5 times.

The system will then make a series of

beeps, indicating it is in test mode.

The first disc will be loaded into the

recorder and the information will be

copied to the internal hard drive.

The system is now ready for the next job

in test mode. To switch to COPY mode,

you must cycle power to the system.

The blank discs will remain blank during

this process and can be used again.

Running in COPY Mode

COPY mode is used when you are ready

to make your copies.

The system will beep one time and the

green LED will start to blink.

Table des matières

Autres manuels MicroBoards Technology duplicateur de disques

MicroBoards Technology

MicroBoards Technology CopyWriter Pro-452RM Manuel utilisateur

MicroBoards Technology

MicroBoards Technology CX-1 Publisher Manuel utilisateur

MicroBoards Technology

MicroBoards Technology MX SERIES Manuel utilisateur

MicroBoards Technology

MicroBoards Technology PF-2 PrintFactory Manuel utilisateur

MicroBoards Technology

MicroBoards Technology GX2-1000 Manuel utilisateur

MicroBoards Technology

MicroBoards Technology CopyWriter Series Manuel utilisateur

MicroBoards Technology

MicroBoards Technology G4 Manuel utilisateur

MicroBoards Technology

MicroBoards Technology DVD Premium Pro Series Manuel utilisateur

MicroBoards Technology

MicroBoards Technology DVD Premium Series Manuel utilisateur

MicroBoards Technology

MicroBoards Technology CX-1 Publisher Manuel utilisateur

MicroBoards Technology

MicroBoards Technology BD Pro Series Manuel utilisateur

MicroBoards Technology

MicroBoards Technology GX-2 Manuel utilisateur

MicroBoards Technology

MicroBoards Technology QD-DVD Manuel utilisateur

MicroBoards Technology

MicroBoards Technology Quic Disc QD-2 Manuel utilisateur

MicroBoards Technology

MicroBoards Technology Orbit II Manuel utilisateur

MicroBoards Technology

MicroBoards Technology StartREC Manuel utilisateur

MicroBoards Technology

MicroBoards Technology CopyWriter Series Manuel utilisateur

MicroBoards Technology

MicroBoards Technology G4 Manuel utilisateur

MicroBoards Technology

MicroBoards Technology GX-1 Manuel utilisateur

MicroBoards Technology

MicroBoards Technology G3 Auto Printer Manuel utilisateur

MicroBoards Technology

MicroBoards Technology GX-2 Manuel utilisateur

MicroBoards Technology

MicroBoards Technology CX-1 Publisher Manuel utilisateur

MicroBoards Technology

MicroBoards Technology G3 Auto Printer Manuel utilisateur

MicroBoards Technology

MicroBoards Technology GX-1 Manuel utilisateur

Manuels duplicateur de disques populaires d'autres marques

Riso

Riso CV Series Manuel

Addonics Technologies

Addonics Technologies HDUS325DX Manuel utilisateur

Carry

Carry Pro118 Manuel utilisateur

CopyPro

CopyPro PowerPro II Manuel utilisateur

Primera

Primera Max Manuel utilisateur

Logicube

Logicube EchoPlus-NG Manuel utilisateur

Silca

Silca Delta 2000 SA Manuel utilisateur

Reflex7

Reflex7 Daisy Chain Series Manuel utilisateur

Vinpower Digital

Vinpower Digital SharkCopier DC Manuel utilisateur

Codonics

Codonics Virtua E Manuel utilisateur

Octave

Octave Copy Master II Manuel utilisateur

Kanguru

Kanguru U2-DVDDUPE-S Manuel utilisateur

StarTech.com

StarTech.com 8STSATDUP11 Manuel utilisateur

DUPLO SEIKO CORPORATION

DUPLO SEIKO CORPORATION Duprinter DP-460 Manuel utilisateur

Addonics Technologies

Addonics Technologies UDFH7 Manuel utilisateur

Vinpower Digital

Vinpower Digital MiniLoader VDX-1 Manuel utilisateur

Addonics Technologies

Addonics Technologies CFASTD5 Manuel utilisateur

Telex

Telex SpinWise Manuel utilisateur