MicroAire 7800 Manuel utilisateur

Model 7800 Battery Sternum Saw

7800-002 Sternum Guard & Accessories

Instruction Manual

- TABLE OF CONTENTS -

Model 7800 Battery Sternum Saw

7800-002 Sternum Guard & Accessories

Instruction Manual

Introduction...................................................................................1

General Warnings......................................................................1-2

Markings.......................................................................................3

Standards & Environmental Parameters........................................4

Technical Data & Specifications.....................................................5

Safety Mechanisms........................................................................5

Instrument Features........................................................................6

Accessory Attachment...................................................................7

System Setup..............................................................................8-9

Troubleshooting...........................................................................10

Cleaning / Decontamination / Sterilization............................11-12

Warranty, Service, and Repair...............................................13-14

References...................................................................................15

Battery & Power Console Information

See Pages 16-18

7800 BATTERY STERNUM SAW

- INTRODUCTION -

This manual has been written to help describe the procedures required to keep the

MicroAire REF 7800 Battery Sternum Saw system operating properly.

Throughout the manual, the following terms are used to identify tips and precautions

that will help avoid accidental injury to patients or personnel, or prevent damage to the

system.

NOTE: Used to point out the easiest means of carrying out techniques.

WARNING: Used to indicate that the safety of the patient and hospital personnel could

be involved.

CAUTION: Used to point out special procedures or precautions that must be followed

to avoid damaging the system/instrument.

- GENERAL WARNINGS -

WARNING: Risk of fire. Replace battery pack only with a MicroAire U.L. classfied

REF 6640-710, REF 7500-710, or REF 7500-735 battery.

WARNING: Explosion Hazard. Not suitable for use in the presence of flammable

anesthetics or oxygen.

WARNING: Electric Shock. Do not remove cover, return to factory for servicing.

WARNING: Type BF rating may only be maintained if the instrument is not used to

bridge between the patient and ground.

WARNING: Use care to ensure that there is no electromagnetic interference between

this device and other devices in use.

WARNING: Prior to use, system components should be inspected and operated to

detect any damage or malfunction. Do not use if damage is apparent.

WARNING: Always point the handpiece away from the patient and surgical team

vicinity when testing.

WARNING: Do not charge the battery in the vicinity of the patient.

WARNING: Do not run the handpiece without the saw blade.

CAUTION: Sternum Guard Attachment

The

REF 7800 Battery Sternum Saw must never be used without the REF

7800-002 sternum guard securely in place and properly oriented with the

MicroAire REF ZR-032M sternum saw blade.

MICROAIRE INSTRUCTION MANUAL

CAUTION: Disconnect battery from handpiece before loading or unloading the saw

blade.

CAUTION: Battery pack should not be left attached to the handpiece when not in use.

This could result in accelerated battery drain.

CAUTION: Make sure the tip of the sternum saw blade is inside the foot of the

sternum guard and does not strike any part of the sternum guard.

Improper alignment of the sternum guard with the saw blade can cause

damage to the sternum saw or saw blade.

CAUTION: If the handpiece will not hold the saw blade or sternum guard securely,

discontinue use and return to the factory for service.

CAUTION: Check Safety Lock and Trigger before operating the handpiece. If the

trigger should stick in the depressed “ON” position, do not use the

handpiece. Immediately remove the battery. Return the instrument to the

factory for service. Always use the Safety Lock when the instrument is

not running.

CAUTION: Check that the battery is fully seated and locked.

CAUTION: Federal Law restricts this device to sale by or on the order of a physician

(or properly licensed practitioner).

NOTE: The

REF 7800 Battery Sternum Saw has been designed and tested to also

operate with the 7025 Direct Power Console (DPC).

NOTE: Disconnect sternum guard, battery, and saw blade prior to sterilization.

Batteries must be sterilized separately.

NOTE: Intermittent duty cycle. Short time operation. 15-second run time.

7800 BATTERY STERNUM SAW

- MARKINGS -

Attention, See instructions for use.

This unit is designed for intermittent operation

Type BF equipment.

0086

European Conformity Mark with MicroAire Notified Body Number

UCLASSIFIED BY UNDERWRITERS LABORATORIES, INC. WITH

RESPECT TO ELECTRIC SHOCK, FIRE, AND MECHANICAL

HAZARDS ONLY IN ACCORDANCE WITH UL 2601-1, CAN/CSA

C22.2 NO. 601-M90 | Control Number: 8R91

DO NOT Lubricate

DO NOT Immerse

Lock

Unlock

Sternum guard alignment arrow

DO NOT Expose To Stray Magnetic Fields

REF Product Catalog Number

SN Product Serial Number

MICROAIRE INSTRUCTION MANUAL

- STANDARDS -

The REF 7800 Battery Sternum Saw meets the following standards:

U 2601-1

WITH RESPECT TO ELECTRIC SHOCK, FIRE, MECHANICAL HAZARD ONLY

IN ACCORDANCE WITH UL 2601-1 AND CAN/CSA C22.2 No. 601.1

EN 60601-1/IEC 601-1

EN 60601-1-2, DIN EN 60601-1-2

- ENVIRONMENTAL PARAMETERS -

OPERATING CONDITIONS

This device has been tested and proven to operate within the following conditions:

SHIPPING & STORAGE CONDITIONS

This device has been tested and proven to operate after repeated exposure to the

following conditions:

Shipping: The materials and components used in the construction of this device were

selected to ensure that the device could be shipped by any standard commercial method

without special handling conditions.

7800 BATTERY STERNUM SAW

- TECHNICAL DATA - SPECIFICATIONS -

Operating Speed: 12,000 CPM (nominal)

Cutting Stroke: 0.117 in. (3.0 mm)

REF 7800 Handpiece Weight

(without battery pack) :

2.65 lb. (1211 g)

REF 6640-710 Battery Weight: 0.95 lb. (431 g)

Battery Voltage: 14.4 volts

Duty Cycle: Short time operation only. 15 second run time.

Rating: 14.4 VDC 225W

- HANDPIECE SAFETY MECHANISMS -

Trigger in Upright - “ON” Position

Trigger in Turned - “OFF” Position

(Trigger can be turned in either direction to be turned

“OFF”)

- REF 7800-002 STERNUM GUARD -

The REF 7800 Battery Sternum Saw requires the use of the included REF 7800-002.

The guard can be attached to the handpiece in either a superior or inferior position,

depending on the position at which the blade was loaded.

MICROAIRE INSTRUCTION MANUAL

- INSTRUMENT COMPONENTS -

Features & Descriptions

1. Blade Locking Collet

Insert the REF ZR-032M Sternum Saw Blade into the blade locking collet by

turning the collet in the direction indicated by the arrow, and then inserting the

blade.

2. Sternum Guard Lock / Release Button

Depress this button to lock or release the REF 7800-002 Sternum Guard from the

handpiece.

3. Trigger / Safety Lock

The REF 7800 Battery Sternum Saw operates at variable speeds and is controlled

by depressing the trigger. The instrument is in the OFF position when the trigger

is not depressed. As the trigger is depressed fully the speed increases from 0%

- 100%. The trigger also serves as the safety lock for the handpiece (see previous

page). After loading the saw blade and attaching the sternum guard and battery,

fully depress the trigger and release one time before use.

4. Battery Release Button

Depress this button to remove a battery/power pack from the handpiece. This

button does not need to be depressed to load a battery/power pack.

7800 BATTERY STERNUM SAW

- ACCESSORY ATTACHMENT -

Battery Attachment

The REF 7800 Battery Sternum Saw must have a fully charged MicroAire U.L.

classfied REF 6640-710 battery installed before each use. The MicroAire REF 7500-

710 and REF 7500-735 batteries may also be used with the REF 7800 Battery Sternum

Saw. To attach the battery to the handpiece, place the battery under the base of the

instrument with the longer side facing the rear of the instrument. Firmly push the

battery into the base of the handpiece until the battery latch clicks into place.

Sternum Guard Attachment

WARNING: The REF 7800 Battery Sternum Saw must never be used without the

REF 7800-002 sternum guard securely in place and properly oriented

with the MicroAire REF ZR-032M sternum saw blade.

MICROAIRE INSTRUCTION MANUAL

- INSTRUMENT SETUP -

CAUTION: Disconnect battery from handpiece before loading or unloading the saw

blade.

CAUTION: Battery pack should not be left attached to the handpiece when not in use.

This could result in accelerated battery drain.

To insert the REF ZR-032M saw blade into the sternum saw handpiece:

1. Make sure the handpiece trigger is set to the “OFF” position and the safety is

“ON” by turning the trigger to one side.

2. If installed, remove the sternum guard from the handpiece by depressing the

release button located on the underside of the sternum guard collet.

3. Twist the blade locking collet into the open position by rotating in the

direction of the arrows.

4. While holding the blade locking collet in the open position, insert a MicroAire

REF ZR-032M saw blade until it is fully seated. The blade may be inserted in

the inferior or superior position.

5. Release the blade locking collet; it should automatically spring back into the

lock position.

To install the REF 7800-002 Sternum Guard on the sternum saw:

1. Make sure the handpiece trigger is set to the “OFF” position and the safety is

“ON” by turning the trigger to one side.

2. Make sure that the MicroAire REF ZR-032M sternum saw blade is securely

installed.

3. Push the sternum guard into the blade/guard collet, over the installed saw

blade. The sternum guard may be inserted easier by depressing the sternum

guard lock button as the sternum guard is installed on the handpiece. Make

sure that the sternum guard is aligned with the saw blade teeth facing away

from the sternum guard. The sternum guard must be completely locked into

place prior to use. Use the alignment arrows to make sure the sternum guard

is properly aligned with the handpiece.

CAUTION: Make sure the tip of the sternum saw blade is inside the foot of the

sternum guard and does not strike any part of the sternum guard.

Improper alignment of the sternum guard with the saw blade can cause

damage to the sternum saw or saw blade.

Test run the assembled handpiece for a few seconds to make sure that the blade and

sternum guard are properly aligned and secure.

1. Move the safety lock to the “OFF” position by turning the trigger back into

the vertical position.

2. Run the handpiece by fully depressing the trigger.

Autres manuels pour 7800

Ce manuel convient aux modèles suivants

Table des matières

Manuels Scie populaires d'autres marques

RIDGID

RIDGID BS1400 Manuel utilisateur

ATIKA

ATIKA BWS 400-2 Manuel utilisateur

RGC

RGC FS20 Manuel utilisateur

Makita

Makita M2300 Manuel utilisateur

IMET Spa

IMET Spa BASIC 300 PLUS SHI Manuel utilisateur

IMET Spa

IMET Spa SIRIO 370 AF-E Manuel utilisateur

Optimum

Optimum OPTisaw CS 275 Manuel utilisateur

Makita

Makita BPB180 Manuel utilisateur

Stihl

Stihl MS 462 C-M Manuel utilisateur

AEG

AEG TS 250 K Manuel utilisateur

Meec tools

Meec tools 004665 Manuel utilisateur

Makita

Makita LS1018L Manuel utilisateur

Ryobi

Ryobi RCS1400 Manuel utilisateur

DeWalt

DeWalt DCS391 Manuel utilisateur

Sealey

Sealey SA72 Manuel utilisateur

skilsaw

skilsaw SPT88 Instructions de montage

Urrea

Urrea SI810 Dimensions et guide d'installation

EINHELL

EINHELL BKG 210/1 Manuel utilisateur