METRON Duo Manuel utilisateur

www.eauto.si [email protected] +386 51 320 538

USER MANUAL

STANDARD(+), DUO(+), TOWER STANDARD(+), TOWER DUO(+)

Simple & SMART wall-mounted and floor-mounted EV Charging Stations

INTRODUCTION

METRON wall-mounted STANDARD/DUO and floor-mounted TOWER STANDARD/DUO are heavy duty all-metal modular EV charging stations designed for long life

operation with maximum user safety features. They also offer smart charging via Metron proprietary Hardwired or Wireless Dynamic Power Control system, OCPP

module with RFID reader for connecting to any cloud backend platform for payment and energy monitoring, ISO 15118 high level communication module for simple

charging authorization and V2G capability, OTA software updates and more.

STANDARD models offer charging power up to 22 kW (3x32A) and DUO models offer charging power up to 2 x 22 kW (3x32A). All models come with oversized main

charging power contactor with 63A current rating for long life operation (20 years+), modular RCCB device (Type B or Type A with 6mA DC) with 10.000A short circuit

breaking capacity and modular automatic circuit breaker with 10.000A short circuit breaking capacity what ensures not only safest domestic use but also allows the

stations to be installed in industrial areas for commercial use. Modular design ensures on-site repairability in max. 15 minutes. The stations with built-in charging cables

can also be equipped with TESLA remote charge port opener & plug unlocker.

Any other use is not allowed and is regarded as improper use.

Before using the EV charging station, please thoroughly read this manual and follow the instructions provided therein. Please keep the manual for future use. If you

are unsure about the proper usage, please contact the manufacturer or your dealer before usage.

Improper use can lead to property damage or personal injury. In such cases, the manufacturer and retailer accept no liability. Warranty will be voided in case of

improper use. You must not:

• modify / manipulate the EV charging station!

• drive over plugs and cables of the EV charging station!

• draw more than maximum specified charging current from the EV charging station!

• connect unsuitable plugs and cables!

• use the EV charging station if damaged!

IMPROPER USE

GENERAL SAFETY INSTRUCTIONS

• Carefully read this security instructions before using the product!

• Never draw more than maximum specified charging current from the EV charging station!

• Children are not allowed to use the EV charging station.

• Keep animals away while using the EV charging station.

• Avoid liquids entering the EV charging station. Never use the EV charging station if the sockets or plugs are wet.

• Only connect undamaged, designated and labelled plugs & cables to the EV charging station.

Podnart 33, SI-4244 Podnart

SETTING THE DESIRED CHARGING CURRENT / POWER without WiFi connection

METRON EV charging stations allow users to set desired charging current / power before being plugged in the electric vehicle. Procedure is simple:

• Press and hold the push button: STATUS LED O-ring switches off immediately.

• After 5 seconds STATUS LED O-ring starts blinking slowly.

• Releasing the push button after a certain number of LED O-ring blinks determines charging current / power as follows:

New charging current / power setting is stored in the memory and it stays the same (even after the power supply is not present anymore)

until the next setting change is performed.

GET STARTED

When no electric vehicle is connected the blue LED STATUS O-ring around station’s black push button(s) glows constantly indicating standby / ready status. When

you plug in the vehicle the STATUS LED O-ring starts blinking slowly what means the vehicle is charging. When your electric vehicle is fully charged the LED O-ring

glows constantly again.

If hardwired or wireless Metron Dynamic Power Control system that offers smart charging is installed the charging power is dynamically controlled in order to not

blow main house fuses; this system is also smartly taking into account the solar / wind / hydro power plant if house has it installed (see chapter “METRON Hardwired

or Wireless Dynamic Power Control” for more info). Users can also via WiFi connect to built-in Metron Charge Control application which offers possibility to change

charging power, delay charging start, monitor real-time charging&house&solar power & energy, activate solar SURPLUS charging and much more (see chapter

“USING THE WiFi METRON Charge Control application” for more info).

If the station is configured in the way authorization is needed for charging start the STATUS LED O-ring shortly blinks every 2 seconds but after successful authorization

(RFID, AutoCharge, OCPP backend, Metron Charge Control app, etc) the STATUS LED O-ring behaves normally.

• Check the EV charging station before use. Do not use the EV charging station if damaged!

• Socket will provide a high voltage (230 / 400 V)!

• Never draw more than maximum specified charging current from the EV charging station!

• Do not use the EV charging station if the socket and plug are wet.

• Only connect undamaged, designated and labelled plugs & cables to the EV charging station.

• Avoid using multiple adapter / power strips as they can lead to overload.

• Don’t unplug during charging process.

• Always operate in the specified order of steps.

Push Button

LED O-ring

Applies to all station versions!

* 1-phase 7,4 kW and 3-phase 22 kW stations only.

1 x 6 A / 1,4 kW

1 x 8 A / 1,8 kW

1 x 10 A / 2,3 kW

1 x 13 A / 3,0 kW

1 x 16 A / 3,7 kW

1 x 20 A / 4,6 kW

1 x 25 A / 5,8 kW

1 x 32 A / 7,4 kW

1 - phase stations 3 - phase stations

Charging current / powerNumber of LED blinks

3 x 6 A / 4,1 kW

3 x 8 A / 5,5 kW

3 x 10 A / 6,9 kW

3 x 13 A / 9,0 kW

3 x 16 A / 11,0 kW

3 x 20 A / 13,9 kW

3 x 25 A / 17,3 kW

3 x 32 A / 22,0 kW

1 x 6 A / 1,4 kW

1 x 8 A / 1,8 kW

1 x 10 A / 2,3 kW

1 x 13 A / 3,0 kW

1 x 16 A / 3,7 kW

1 x 20 A / 4,6 kW

1 x 25 A / 5,8 kW

1 x 32 A / 7,4 kW

SYMBOLS USED

The following symbols are used in this manual and on the product:

This symbol indicates a danger with a risk of coursing serious injury or death or damage if not avoided.

CE symbol is a mark of conformity indicating that a product complies with European Union directives and regulations.

This symbol signifies the requirement for separate disposal of electrical and electronic waste. See chapter disposal.

Please read the manual before using the EV charging station.

Risk of electric shock due to dangerous voltage when used incorrectly.

Do not use and store the adapter below or above the specified temperature.

REMOTE CHARGE PORT OPEN & PLUG UNLOCK for TESLA electric vehicles

Metron charging stations with built-in charging cables can be equipped with TESLA remote charge port open & plug unlock electronics. Pressing a “2-function” button

on the vehicle Type 2 plug sends a remote-control signal to your TESLA vehicle charge port which then opens. Signal range is usually between 3 and 15 meters. This

feature eliminates user “touching” the smart phone or Tesla central screen in order to open the charge port. Remote-control signal also wakes-up the Tesla vehicle

from sleep - sometimes the button needs to be pressed several times to wake-up the vehicle.

To unplug while still charging or when charging completed press and hold the “2-function” button for a second. The car will unlock the vehicle plug (only if car is

unlocked / owner nearby!) and then you can unplug it. Plug unlock function works even if the charging station is not powered (manually turned off, grid power

outage, etc).

This feature once again eliminates the need for user “touching” the smart phone or Tesla central screen in order to unlock the charging plug from Tesla charge port.

“2-function” Button

USING THE WiFi METRON Charge Control application (SMART »+« charging stations only)

Smart EV charging stations marked with “+” have a built-in WiFi access point with web server what enables users to connect to it wirelessly by any smart phone, tablet

or laptop PC. As there is a web server inside with preloaded METRON Charge Control application you don’t need to install any additional program / application on

your device because the METRON Charge Control simply runs in your favorite web browser (Google Chrome, Microsoft Edge, Mozilla Firefox…) on any operating

system (Google Android, Apple iOS, Microsoft Windows, Huawei HarmonyOS, Linux…) you have on your smart phone, tablet or laptop PC.

Using the web-based METRON Charge Control application user can:

•Disconnect the station from power, press the “Push Button” and keep it pressed.

•Connect the station to power.

•The blue STATUS LED O-ring starts blinking 2 times.

• After 30 seconds the STATUS LED O-ring will turn-on for 3 seconds and then turn-of.

•Release the “Push Button” and WiFi name (ssid) & password are reset to default values.

To connect to the WiFi METRON Charge Control application you need to do the following:

•

Make sure the charging station is energized (connected to power).

Go to WiFi menu in your smart phone, tablet or laptop PC and search for WiFi networks.

Find “METRON Station 1” (default) network and connect to it; enter the WiFi password 12345678 (this is default - it is

recommended that you change it in the METRON Charge Control application).

Scan QR code you find on the station and follow the link (it will open your default web browser and launch the

Metron Charge Control automatically); OR open your favorite web browser and type in the following IP address:

http://192.168.4.4

The METRON Charge Control application will be loaded immediately. Up to 5 users (devices) at a time can be

wirelessly connected to the station and all connected devices will automatically receive all the latest data; for

example, if one user changes the charging current with the slider all others will see that on their screens.

•

Set the desired charging current and delay charging start.

Turn on / off solar SURPLUS charging if solar power plant is installed.

See all the real time measurements of charging power, charging current and charging energy.

Change WiFi password and WiFi name (ssid).

Connect the charging station to local WiFi network and also set the charging station internet access in the WiFi router (advanced users).

OTA (over-the-air) install UPDATES for application firmware via WiFi.

If METRON Dynamic EV Charging Unit for SMART charging with house main fuse protection is installed the user can also see house load, house energy

consumption, solar power and solar energy production.

Establish station internet connection via OCPP protocol to backend systems (Metron or others) for station control, payment for charging, energy monitoring,

etc via internet (OCPP module needed)

Locally authorize RFID cards (OCPP module needed)

Locally authorize electric vehicles via supported AutoCharge function (ISO 15118 module and OCPP module needed)

If you forget the WiFi password you’ve set, you need to do the following:

The METRON Charge Control application is intuitive and usually doesn’t need more instructions to be used; just browse and explore the functions. Where the

additional user info is required important user instructions are explained under “notes”. If you don’t understand something please feel free to contact Metron.

METRON Hardwired and Wireless Dynamic Power Control

(SMART »+« charging stations only)

Smart “+” marked EV charging stations can be equipped with Hardwired (1 station per main fuse) or Wireless Dynamic Power Control system (up to 150 charging

stations fer main fuse) that is always monitoring the load at house main fuse with electric current sensors and dynamically adjusting (lowering or rising) the charging

current/power of your electric vehicle in the way the main house fuse never gets overloaded (never blows-up). If the house has a solar (or wind/hydro) power plant

installed this system allows higher current/power charging than would be allowed by the main fuse and it also enables the possibility of user activated solar SURPLUS

charging what means the vehicle will be charged only with excess solar power without taking any energy from the grid. METRON Wireless Dynamic Power Control

system is designed to work with 1-phase and 3-phase power systems. To be short, METRON Dynamic Power Control system enables users to charge their electric

vehicle without worrying about the load other household appliances might draw from the in-house grid.

For 1-station Hardwired Dynamic Power Control the installer needs only to place clamp-on current sensors to main house power inlet and solar power plant (if

present). In case of dynamically controlling 2 or more charging stations this can be done wirelessly only as this greatly reduces laying cables and thus cost. For

METRON Wireless Dynamic Power Control all you need is 1 pcs METRON Dynamic EV Charging Unit (model 3FD-3) with clamp-on current sensors. This way up to 150

Metron wall-mounted, floor mounted or even METRON smart portable EV charging stations can be controlled and main fuses with rated currents up to 1000A are

supported.

Note: Wireless signal has an open-air space range of 500m with built-in antenna and up to 2000m with additional antennas on the METRON Dynamic EV Charging

Unit (model 3FD-3). If the system is installed within one house usually no additional antenna is needed.

STATUS NOTIFICATION BY LED O-ring

Charging terminated due to overcurrent (unplug to reset, vehicle service may be needed)Slow blinking 9 times

Rapid blinking (plugged in or not plugged in) Station or vehicle fault

STATUS LED O-ring state NOTIFICATION

Slow blinking when power supply is applied

Constantly on when not plugged in

Slow blinking when plugged in

Constantly on when plugged in

Indicating previous saved current setting

Stand-by / Ready to charge

Charging

Electric vehicle fully charged

Electric vehicle requests room ventilation (no charging)

Slow blinking 2 times when plugged in

Charging temporary terminated by Dynamic Power Control system, no wireless signal or

charging terminated by user

Slow blinking 4 times (plugged in or not plugged in)

Detailed schematics for installing METRON Dynamic Power Control system are located in a separate installation manual, intended for

qualified installers only.

TECHNICAL SPECIFICATIONS

Charging station plug / socket type

Max. charging power

Max. charging current

Possible charging current settings

(by user)

Locking mechanism for Type 2

charging socket

Main charging contactor rated

current-carrying capacity

Analog input for controlling charging

current/power (0-5V or 0-10V or 0-20mA)

Digital input for charging

authorization/activation by external device

WiFi Metron Charge Control app.

(web based)

METRON proprietary Hardwired or

Wireless Dynamic Power Control system

Differential protection - Residual

Current Circuit Breaker (RCCB)

Overcurrent protection

Tesla remote for opening charge port

and unlocking the plug – integrated in

Type 2 plug

Charging cable (applicable for stations

with cable and charging plug)

Rated Voltage

Operating voltage / frequency

Overvoltage category

MID certified Energy meter

4G/5G Router

Network/ethernet switch

Supported WiFi standards

WiFi speed

WiFi security

WiFi signal range

Type 2 or Type 1 plug holder

OCPP 1.6J module with integrated WiFi

and Ethernet internet connectivity for

remote monitoring and payment, also

supports OCPP load management

Enclosure material

RFID reader for ISO/IEC 14443A

compatible MIFARE cards/tags, internal

storage for 100 cards with energy meter

for each card

ISO 15118 High-level communication

module with AutoCharge and future

V2G capability, internal storage for 100

vehicles with energy meter for each

vehicle (AutoCharge)

YES, Smart “+” models only

STANDARD(+) &

TOWER STANDARD(+)

3,7 kW or 7,4 kW (1-phase)

11 kW or 22 W (3-phase)

16 A or 32 A (1-phase),

3x16 A or 3x32 A (3-phase)

6/8/10/13/16/20**/25**/ 32**A via front button,

“+” models from 6A in 1A steps to 16A or 32A via

WiFi Metron Charge Control app.

** 32 A rated stations only

Straight (any length) or SPIRAL

Black or Orange color

Premium quality according to EV charge cable

standard EN 50620

Type 2 / Type 1 (IEC 62196 / SAE J1772) female plug

or Type 2 Female charging socket

63 A (all models without exceptions to ensure

safe and long-lasting operation)

YES, all models

YES, Smart “+” models only

1 x Type B or Type A 30 mA AC with 6mA DC;

10.000 A short circuit breaking capacity

1 x circuit breaker C20A or C40A for charging + 1 x

circuit breaker C2A for electronics;

10.000 A short circuit breaking capacity

STANDARD(+): 2-3mm thick steel + ultra clear

tempered glass with white ceramic back coat

TOWER STANDARD(+): 1,5mm thick stainless steel +

ultra clear tempered glass with white ceramic

back coat

230 Vac (1-phase), 400 Vac (3-phase)

from 180 V up to 270 V (phase voltage) / 50 Hz

III (IEC/EN 60664)

optional for all models

optional for Smart “+” models only

IEEE 802.11b/g/n (Smart “+” models only)

up to 150 Mbit/s (Smart “+” models only)

WPA2 (Smart “+” models only)

up to 20 m (Smart “+” models only)

optional for all models with charging cable

optional for all models with Type 2 plug

optional for Smart “+” models only

optional for all models with Type 2 socket

5 WPower consumption

DUO(+) &

TOWER DUO(+)

Type 2 / Type 1 (IEC 62196 / SAE J1772) female plug

or Type 2 Female charging socket

2 x 3,7 kW or 2 x 7,4 kW (1-phase), 2 x 11 kW or

2 x 22 kW (3-phase)

Straight (any length) or SPIRAL

Black or Orange color

Premium quality according to EV charge cable

standard EN 50620

2 x 16 A or 2 x 32 A (1-phase), 2 x 3x16 A or

2 x 3x32 A (3-phase)

6/8/10/13/16/20**/25**/ 32**A via front button, “+” models

from 6A in 1A steps to 16A or 32A via WiFi Metron Charge

Control app. (for each socket/plug independently)

** 32 A rated stations only

63 A (all models without exceptions to ensure

safe and long-lasting operation)

YES, all models

YES, Smart “+” models only

2 x Type B or Type A 30 mA AC with 6mA DC;

10.000 A short circuit breaking capacity

2 x circuit breaker C20A or C40A for charging + 2 x

circuit breaker C2A for electronics;

10.000 A short circuit breaking capacity

DUO(+): 2-3mm thick steel + ultra clear tempered glass

with white ceramic back coat

TOWER DUO(+): 1,5mm thick stainless steel + ultra clear

tempered glass with white ceramic back coat

230 Vac (1-phase), 400 Vac (3-phase)

from 180 V up to 270 V (phase voltage) / 50 Hz

III (IEC/EN 60664)

optional for all models

optional for Smart “+” models only

IEEE 802.11b/g/n (Smart “+” models only)

up to 150 Mbit/s (Smart “+” models only)

WPA2 (Smart “+” models only)

up to 20 m (Smart “+” models only)

optional for all models with charging cable

optional for all models with Type 2 plug

optional for Smart “+” models only

optional for all models with Type 2 socket

YES, Smart “+” models only

10 W

Additional independent numerical

(software) overcurrent protection

(acts on charging contactor)

STANDARD(+), DUO(+), TOWER STANDARD(+), TOWER DUO(+)

Simple & SMART wall-mounted and floor-mounted EV Charging Stations

Rev. 6 2/2024

RCCB is an acronym for Residual Current Circuit Breaker - sometimes it can be called also Earth Leakage Circuit Breaker or Safety Switch. Its purpose is to prevent you

from getting a fatal electric shock if you touch live part, such as a bare copper wire under high voltage. RCCBs offer a level of personal protection that ordinary fuses/-

circuit-breakers cannot provide. RCCB constantly monitors the electric current flowing through one or more circuits which it protects. If it detects electricity flowing

down an unintended path, such as through a person who has touched a live part, the RCCB will switch the circuit off very quickly, significantly reducing the risk of

death or serious injury. Every charging station has integrated Type A 30mA AC + 6mA DC or Type B RCCB what ensures maximum possible level of personal protection

as it protects users from AC, pulsating DC and pure DC leakage currents.

WHAT IS RCCB AND HOW DOES IT WORK?

LIMITED WARRANTY

METRON warrants its product to the original consumer purchaser that it will repair, or replace, any product that is determined to be defective for the following terms:

Two (2) years from date of purchase on all components. To be eligible for repair or replacement under this warranty, the product in question must be sent back to

METRON within the warranty period and the original consumer purchaser must comply with the following conditions: The product thereof must not have been

modified or altered in any way by an unauthorized source; The product thereof must have been used in accordance with the user manual.

This limited warranty does not cover: Damage due to improper use; Accidental or intentional damage; Misuse, abuse, corrosion, or neglect; Product impaired by

severe natural conditions, such as excessive hail storms, lightning strikes, tornados, flooding, ice or other natural occurrences; Damage due to improper packaging

on return shipment. Any and all labor charges for troubleshooting, removal or replacement of the product are not covered by this warranty and will not be honored

by METRON. All shipping costs regarding repair or replacement of the product is to be pre-paid by the original consumer purchaser.

All our products are produced in a carbon neutral way by using "Sustainable energy cycle" method. Production plant where we make charging cables and portable

charging stations is the first fully sustainable production facility for EV charging cables. All energy needed for the heating and cooling of the building, production

process and for transportation of goods and employees (except deliveries of heavy materials by trucks), is produced by 2 photovoltaic power plants and stored in

4 storage batteries. Almost all of the raw materials we use (cables, plugs) are produced in EU, to shorten supply routes and support local economy.

Buying our products helps developing sustainable economy.

GREEN PRODUCTION

Use only a dry or damp cloth for cleaning the switched off EV charging station. Do not use cleaning detergents.

CLEANING

The symbol "crossed-out trash can" signifies the requirement for separate disposal of electrical and electronic waste. These devices may contain

hazardous and environmentally harmful substances. Please take such devices to a designated collection point for the recycling of electrical and electronic

equipment and do not dispose of them in regular household waste. You can obtain further information from local waste disposal services or the company

from which you purchased the product.

DISPOSAL

• EV charging station must be switched off before cleaning!

• Avoid water getting to contact parts!

STANDARD(+) &

TOWER STANDARD(+)

DUO(+) &

TOWER DUO(+)

UV resistance

Operating ambient air temperature range

Storage temperature

Yes (all parts)

from -30°C to +50°C

from -40 °C to +70 °C

Yes (all parts)

from -30°C to +50°C

from -40 °C to +70 °C

Relative ambient humidity

(operation and storage)

Maximum operating altitude

max 95 % (without condensation)

2000 m

max 95 % (without condensation)

2000 m

IP Rating

IK Rating

IP54 (rain proof)

IK10 (impact/shock proof)

IP54 (rain proof)

IK10 (impact/shock proof)

Minimum required power supply cable

cross section

Access for maintenance and repair

3G2,5 mm2 for 3,7 kW

3G6 mm2 for 7,4 kW

5G2,5 mm2 for 11 kW

5G6 mm2 for 22 kW

3G6 mm2 for 2 x 3,7 kW

3G16 mm2 for 2 x 7,4 kW

5G6 mm2 for 2 x 11 kW

5G16 mm2 for 2 x 22 kW

Doors with key lock Doors with key lock

Dimensions (HxWxD) STANDARD(+): 340 x 240 x 100 mm

TOWER STANDARD(+): 1400 x 200 x 150 mm

DUO(+): 500 x 370 x 100 mm

TOWER DUO(+): 1400 x 300 x 200 mm

Weight STANDARD(+): Approx. 8-10 kg

TOWER STANDARD(+): Approx. 20-22 kg

DUO(+): Approx. 16-20 kg

TOWER DUO(+): Approx. 30-34 kg

Paint/anti-corrosion protection Structural powder coat

Color Anthracite grey, other colors on request Anthracite grey, other colors on request

Structural powder coat

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels METRON Chargeur de batteries

METRON

METRON Standard(+) Manuel utilisateur

METRON

METRON PC03 Manuel utilisateur

METRON

METRON PC03X Manuel utilisateur

METRON

METRON PC02Y+ Manuel utilisateur

METRON

METRON Nano(+) Manuel utilisateur

METRON

METRON Nano(+) Manuel utilisateur

METRON

METRON Nano Manuel utilisateur

METRON

METRON TOWER/STANDARD+ Manuel utilisateur

Manuels Chargeur de batteries populaires d'autres marques

AA Portable Power Corp

AA Portable Power Corp Universal Smart Charger Manuel utilisateur

Enelion

Enelion Vertica Manuel utilisateur

RCA

RCA CHU6 Manuel utilisateur

ANSMANN

ANSMANN ALCT 6/24-10 Manuel utilisateur

Hitachi

Hitachi UC 18YRSL Guide de dépannage

Olympus

Olympus B-20 LPC Manuel utilisateur

Exibel

Exibel ZH1708143 Manuel utilisateur

Lenmar

Lenmar Mach 1 Manuel utilisateur

CTEK

CTEK MXS 5.0 Manuel utilisateur

ABB

ABB HT842379 Manuel utilisateur

Nitecore

Nitecore Superb Charger SC4 Manuel utilisateur

Renogy

Renogy RBC2125DS-21W Manuel utilisateur

Braun

Braun BWC02M Manuel utilisateur

CTEK

CTEK MXS 3.6 Manuel utilisateur

Black & Decker

Black & Decker BDV090 Manuel utilisateur

Trinity

Trinity DPD Manuel utilisateur

Hulkman

Hulkman Sigma 1 Manuel utilisateur

IKEA

IKEA koppla Manuel utilisateur