Metrohm 815 Manuel utilisateur
815 Robotic Soliprep for LC
2.815.4110
Manual
8.815.8002EN / 2020-02-29
Metrohm AG
CH-9100 Herisau
Switzerland
Phone +41 71 353 85 85
Fax +41 71 353 89 01
www.metrohm.com
815 Robotic Soliprep for LC
2.815.4110
Manual
8.815.8002EN / 2020-02-29
Technical Communication
Metrohm AG
CH-9100 Herisau
This documentation is protected by copyright. All rights reserved.
This documentation has been prepared with great care. However, errors
can never be entirely ruled out. Please send comments regarding possible
errors to the address above.
￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭ Table of contents
815 Robotic Soliprep for LC ￭￭￭￭￭￭￭￭ III
Table of contents
1 Introduction 1
1.1 Instrument description ......................................................... 1
1.2 Intended use ......................................................................... 2
1.3 About the documentation ................................................... 2
1.3.1 Symbols and conventions ........................................................ 2
1.4 Safety instructions ................................................................ 3
1.4.1 General notes on safety ........................................................... 3
1.4.2 Electrical safety ........................................................................ 3
1.4.3 Personnel safety ....................................................................... 4
1.5 Recycling and disposal ......................................................... 5
2 Installation 6
2.1 Preparing the Sample Processor ......................................... 6
2.2 Connecting the instrument to the power grid ................... 8
2.3 Installing MagIC Net™ ......................................................... 9
2.4 Configuring the Swing Heads .............................................. 9
2.5 Mounting the Swing Heads ............................................... 13
2.6 Mounting the deflector, Luer connector and collection
container ............................................................................. 16
2.7 Mounting the transfer robotic arm ................................... 20
2.8 Mounting the Polytron robotic arm .................................. 24
2.9 Washing station and drip pan ........................................... 25
2.10 Connecting and setting up the peristaltic pump ............. 27
2.11 Installing the rinsing tubing .............................................. 29
2.12 Placing tubing and cables in the guide chain .................. 29
2.13 Assembling and mounting the Polytron® drive ................ 31
2.14 Mounting the rinsing tubings for the Polytron® ............. 31
2.15 Connecting the Polytron® .................................................. 32
2.16 Mounting the safety shield ................................................ 33
2.17 Installing the Dosino .......................................................... 34
2.18 Equipping the rack ............................................................. 37
3 Defining rack positions 39
4 Adjusting rack and robotic arm 41
Table of contents ￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭
IV ￭￭￭￭￭￭￭￭ 815 Robotic Soliprep for LC
5 Setting lift positions 45
5.1 Lift position for sample beakers ....................................... 45
5.2 Lift position for picking up needles and filters ................ 46
5.3 Lift positions for special beakers ...................................... 47
5.4 Lift positions for stripping needles and filters ................. 49
5.5 Lift position for the Luer connector .................................. 51
5.6 Lift position for the Polytron ............................................. 52
5.7 Lift position for the washing station ................................ 53
6 Controlling the Polytron® 55
7 Accessories 60
Index 61
￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭ 1 Introduction
815 Robotic Soliprep for LC ￭￭￭￭￭￭￭￭ 1
1 Introduction
1.1 Instrument description
The 815 Robotic Soliprep systems are automation systems suitable for a
variety of uses. They have been designed exclusively for utilization in facto-
ries and laboratories and cover a wide range of applications. Soliprep sys-
tems can be used for automation purposes wherever a complex sample
preparation of solid substances is required, e.g. for pharmaceutical or food
analysis.
The Robotic Sample Processors, which have proven their worth for many
years, form the basis for a versatile system that has been expanded to
include opportunities for the dispersion, filtration and bottling of samples
of all sorts. This versatile concept can be expanded as required.
Thanks to the integration of high-performance communication interfaces
(USB, RS-232), they can be incorporated seamlessly into a variety of instru-
ment systems, and not only those manufactured by Metrohm. Operation
by the high performance tiamo™ or MagIC Net™ software ensures not
only user-friendly operation and programming of automation sequences,
but also allows 100% conformity for the entire automation system with
FDA (Food and Drug Administration) regulations. This applies in particular
with regard to regulation 21 CFR Part 11, Electronic records and signa-
tures.
815 Robotic Soliprep for Liquid Chromatography
￭Dispersion, filtration, dilution and sample transfer
The universal automation system for sample preparation in instrumental
chromatography. A workstation equipped with a dispersion device is used
to shred the sample. The dispersion aggregate is cleaned in a special rins-
ing station. The second workstation is equipped for sample transfer with a
universal robotic arm with a Luer adapter. It is used for picking up syringe
needles (for aspirating the dispersed sample and bottling the filtrate in
sealed vials) and membrane filters (for filtering and injecting the sample in
a capillary).
Needles and filters are charged in replaceable inserts. The needles and fil-
ters are automatically stripped off after use and disposed of in a waste
container.
Two versatile dosing drives (800 Dosino) are used as an auxiliary device for
diluting the sample and for transferring the sample solution.
1.2 Intended use ￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭
2￭￭￭￭￭￭￭￭ 815 Robotic Soliprep for LC
1.2 Intended use
The 815 Robotic Soliprep for LC is designed for the automatic analysis of
larger-sized sample series in analytical laboratories. The functioning of the
automation system comprises crushing, homogenizing and dissolving of
solid samples as well as filtering and transferring the resulting sample solu-
tions. Its main area of application is the sample preparation in instrumen-
tal chromatography. It is not suitable for usage in biochemical, biological
or medical environments in its basic equipment version.
This instrument is suitable for processing chemicals and flammable sam-
ples. Therefore, the use of the 815 Robotic Soliprep for LC requires the
user to have basic knowledge and experience in handling toxic and caustic
substances. Knowledge regarding the application of fire prevention meas-
ures prescribed for laboratories is also mandatory.
1.3 About the documentation
1.3.1 Symbols and conventions
The following symbols and formatting may appear in this documentation:
Cross-reference to figure legend
The first number refers to the figure number, the sec-
ond to the instrument part in the figure.
Instruction step
Carry out these steps in the sequence shown.
Method Dialog text, parameter in the software
File ▶ New Menu or menu item
[Next] Button or key
WARNING
This symbol draws attention to a possible life-threat-
ening hazard or risk of injury.
WARNING
This symbol draws attention to a possible hazard due
to electrical current.
WARNING
This symbol draws attention to a possible hazard due
to heat or hot instrument parts.
￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭ 1 Introduction
815 Robotic Soliprep for LC ￭￭￭￭￭￭￭￭ 3
WARNING
This symbol draws attention to a possible biological
hazard.
CAUTION
This symbol draws attention to possible damage to
instruments or instrument parts.
NOTE
This symbol highlights additional information and
tips.
1.4 Safety instructions
1.4.1 General notes on safety
WARNING
Operate this instrument only according to the information contained in
this documentation.
This instrument left the factory in a flawless state in terms of technical
safety. To maintain this state and ensure non-hazardous operation of the
instrument, the following instructions must be observed carefully.
1.4.2 Electrical safety
The electrical safety when working with the instrument is ensured as part
of the international standard IEC 61010.
WARNING
Only personnel qualified by Metrohm are authorized to carry out service
work on electronic components.
WARNING
Never open the housing of the instrument. The instrument could be
damaged by this. There is also a risk of serious injury if live components
are touched.
There are no parts inside the housing which can be serviced or replaced
by the user.
1.4 Safety instructions ￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭
4￭￭￭￭￭￭￭￭ 815 Robotic Soliprep for LC
Supply voltage
WARNING
An incorrect supply voltage can damage the instrument.
Only operate this instrument with a supply voltage specified for it (see
rear panel of the instrument).
Protection against electrostatic charges
WARNING
Electronic components are sensitive to electrostatic charges and can be
destroyed by discharges.
Do not fail to pull the power cord out of the power socket before you
set up or disconnect electrical plug connections at the rear of the
instrument.
1.4.3 Personnel safety
WARNING
Personnel are not permitted to reach into the working area of a Sample
Processor while operations are running!
A considerable risk of injury exists for users who undertake manual
interventions to the automatic running of the instrument.
The various drives in a Sample Processor (including Swing Heads) have
considerable power in order to ensure that they are able to be operated
perfectly, even with greater loads. They are equipped with an electronic
overload protection that is activated in the presence of excessive mechani-
cal resistance.
WARNING
The Sample Processor does not provide sufficient protection during the
processing of potentially infectious samples or reagents.
Implement appropriate protective measures.
Autres manuels pour 815
1
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Metrohm Équipement de laboratoire
Metrohm
Metrohm 930 Compact IC Flex ChS/Deg Manuel utilisateur
Metrohm
Metrohm 862 Manuel utilisateur
Metrohm
Metrohm Eco Titrator Manuel utilisateur
Metrohm
Metrohm 848 Titrino plus Manuel utilisateur
Metrohm
Metrohm 869 Manuel utilisateur
Metrohm
Metrohm Titrino 758 KFD Manuel utilisateur
Metrohm
Metrohm 889 IC Sample Center Basic Manuel utilisateur
Metrohm
Metrohm 815 Manuel utilisateur
Metrohm
Metrohm ProfIC Vario 6 Anion Manuel utilisateur
Metrohm
Metrohm 700 Dosino Manuel utilisateur
Metrohm
Metrohm 753 Manuel utilisateur
Metrohm
Metrohm 942 Extension Module Vario ONE/Deg Manuel utilisateur
Metrohm
Metrohm 761 Compact IC Manuel utilisateur
Metrohm
Metrohm 832 KF Thermoprep Manuel utilisateur
Metrohm
Metrohm 885 Compact Oven SC Manuel utilisateur
Metrohm
Metrohm 860 KF Manuel utilisateur
Metrohm
Metrohm 883 Basic IC plus Manuel utilisateur
Metrohm
Metrohm Combustion-IC-System Manuel utilisateur
Metrohm
Metrohm 930 Compact IC Flex Oven/ChS/Deg Manuel utilisateur
Metrohm
Metrohm 858 Manuel utilisateur
Manuels Équipement de laboratoire populaires d'autres marques
Agilent Technologies
Agilent Technologies 5800 ICP-OES Manuel utilisateur
Endress+Hauser
Endress+Hauser Cleanfit CPA875 Manuel utilisateur
NI
NI PXI-5422 Manuel
Collomix
Collomix Aqix Manuel utilisateur
SPEX SamplePrep
SPEX SamplePrep 6875 Freezer/Mill Series Manuel utilisateur
Ocean Insight
Ocean Insight FLAME-NIR+ Manuel utilisateur
