Metrohm 801 Manuel utilisateur
801 Stirrer
Manual
8.801.8001EN
Metrohm AG
CH-9101 Herisau
Switzerland
Phone +41 71 353 85 85
Fax +41 71 353 89 01
www.metrohm.com
801 Stirrer
Manual
8.801.8001EN 06.2010 ek
Teachware
Metrohm AG
CH-9101 Herisau
This documentation is protected by copyright. All rights reserved.
Although all the information given in this documentation has been
checked with great care, errors cannot be entirely excluded. Should you
notice any mistakes please send us your comments using the address
given above.
Documentation in additional languages can be found on
http://products.metrohm.com under Literature/Technical documenta-
tion.
￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭ Table of contents
801 Stirrer ￭￭￭￭￭￭￭￭ III
Table of contents
1Introduction 1
1.1 Instrument description ......................................................... 1
1.2 About the documentation ................................................... 1
1.2.1 Symbols and conventions ........................................................ 1
1.3 Safety instructions ................................................................ 2
1.3.1 General notes on safety ........................................................... 2
1.3.2 Electrical safety ........................................................................ 2
1.3.3 Working with liquids ................................................................ 3
1.3.4 Flammable solvents and chemicals ........................................... 3
1.3.5 Recycling and disposal ............................................................. 4
2Overview of the instrument 5
3Installation 6
3.1 Setting up the instrument .................................................... 6
3.1.1 Packaging ................................................................................ 6
3.1.2 Checks .................................................................................... 6
3.1.3 Location .................................................................................. 6
3.2 Mounting the 801 Stirrer ..................................................... 7
3.3 Connecting the 801 Stirrer .................................................. 9
4Technical specifications 11
4.1 Rotational speed ................................................................. 11
4.2 Power supply ...................................................................... 11
4.3 Safety specifications ........................................................... 11
4.4 Electromagnetic compatibility (EMC) ................................ 11
4.5 Ambient temperature ......................................................... 12
4.6 Dimensions .......................................................................... 12
4.7 Material ............................................................................... 12
5Conformity and warranty 13
5.1 Declaration of Conformity ................................................. 13
5.2 Quality Management Principles ........................................ 14
5.3 Warranty (guarantee) ......................................................... 15
6Accessories 16
6.1 Scope of delivery ................................................................ 16
6.1.1 801 Stirrer 2.801.0010 (without stand) .................................. 16
Table of contents ￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭
IV ￭￭￭￭￭￭￭￭ 801 Stirrer
6.1.2 801 Stirrer 2.801.0040 (with stand) ....................................... 17
6.2 Optional accessories ........................................................... 19
6.2.1 801 Stirrer 2.801.0010, 2.801.0040 ...................................... 19
￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭ Table of figures
801 Stirrer ￭￭￭￭￭￭￭￭ V
Table of figures
Figure 1 Front 801 Stirrer ................................................................................ 5
Figure 2 Rear 801 Stirrer ................................................................................. 5
Figure 3 Connecting the 801 Stirrer .............................................................. 10
Figure 4 Connecting the Dosino to the 801 Stirrer. ....................................... 10
￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭ 1 Introduction
801 Stirrer ￭￭￭￭￭￭￭￭ 1
1 Introduction
1.1 Instrument description
The magnetic stirrer 801 Stirrer including base plate, support rod and elec-
trode holder supplements the Titrino plus, Titrandos, Sample Processors,
805 Dosimats and 780/781 pH Meter.
It is directly connected to an analysis device via an MSB connection cable.
1.2 About the documentation
Caution
Please read through this documentation carefully before putting the
instrument into operation. The documentation contains information
and warnings which the user must follow in order to ensure safe opera-
tion of the instrument.
1.2.1 Symbols and conventions
The following symbols and styles are used in this documentation:
Cross-reference to figure legend
The first number refers to the figure number, the
second to the instrument part in the figure.
Instruction step
Carry out these steps in the sequence shown.
Warning
This symbol draws attention to a possible life hazard
or risk of injury.
Warning
This symbol draws attention to a possible hazard due
to electrical current.
Warning
This symbol draws attention to a possible hazard due
to heat or hot instrument parts.
1.3 Safety instructions ￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭￭
2￭￭￭￭￭￭￭￭ 801 Stirrer
Warning
This symbol draws attention to a possible biological
hazard.
Caution
This symbol draws attention to a possible damage of
instruments or instrument parts.
Note
This symbol marks additional information and tips.
1.3 Safety instructions
1.3.1 General notes on safety
Warning
This instrument may only be operated in accordance with the specifica-
tions in this documentation.
This instrument has left the factory in a flawless state in terms of technical
safety. To maintain this state and ensure non-hazardous operation of the
instrument, the following instructions must be observed carefully.
1.3.2 Electrical safety
The electrical safety when working with the instrument is ensured as part
of the international standard IEC 61010.
Warning
Only personnel qualified by Metrohm are authorized to carry out service
work on electronic components.
Warning
Never open the housing of the instrument. The instrument could be
damaged by this. There is also a risk of serious injury if live components
are touched.
There are no parts inside the housing which can be serviced or replaced
by the user.
Autres manuels pour 801
1
Table des matières
Autres manuels Metrohm Équipement de laboratoire
Metrohm
Metrohm 940 Professional IC Vario Series Manuel utilisateur
Metrohm
Metrohm Misa Manuel utilisateur
Metrohm
Metrohm 843 Pump Station Manuel utilisateur
Metrohm
Metrohm Dosimat plus 876 Manuel utilisateur
Metrohm
Metrohm Autosampler plus 919 IC Manuel utilisateur
Metrohm
Metrohm 904 Titrando Manuel utilisateur
Metrohm
Metrohm 726 Manuel utilisateur
Metrohm
Metrohm 730 Manuel utilisateur
Metrohm
Metrohm 862 Manuel utilisateur
Metrohm
Metrohm 786 Swing Head Manuel utilisateur
Metrohm
Metrohm Eco Titrator Manuel utilisateur
Metrohm
Metrohm 815 Manuel utilisateur
Metrohm
Metrohm 810 Manuel utilisateur
Metrohm
Metrohm 799 GPT Titrino Manuel utilisateur
Metrohm
Metrohm 774 Manuel utilisateur
Metrohm
Metrohm 785 DMP Titrino Manuel utilisateur
Metrohm
Metrohm 905 Titrando Manuel utilisateur
Metrohm
Metrohm Professional IC Vario 940 Manuel utilisateur
Metrohm
Metrohm 942 Extension Module Vario ChS-PP Manuel utilisateur
Metrohm
Metrohm OMNIS 2.1002.0 10 Series Manuel utilisateur
Manuels Équipement de laboratoire populaires d'autres marques
Agilent Technologies
Agilent Technologies 5800 ICP-OES Manuel utilisateur
Endress+Hauser
Endress+Hauser Cleanfit CPA875 Manuel utilisateur
NI
NI PXI-5422 Manuel
Collomix
Collomix Aqix Manuel utilisateur
SPEX SamplePrep
SPEX SamplePrep 6875 Freezer/Mill Series Manuel utilisateur
Ocean Insight
Ocean Insight FLAME-NIR+ Manuel utilisateur
