Metek BPS Series Manuel utilisateur

M440077-01 Rev B www.programmablepower.com

BPS Series

AC Power Source

User Manual

2 programmablepower.com

User Manual

California Instruments - AC Power Source

AMETEK Programmable Power.

Models Covered in this manual:

BPS30-1

BPS30-3

BPS45-1

BPS45-3

BPS75-3

BPS90-3

BPS150-3

BPS180-3

AMETEK Programmable Power

BPS Series User Manual - M440077-01 Rev B 3

About AMETEK

AMETEK Programmable Power, Inc., a Division of AMETEK, Inc., is a global leader

in the design and manufacture of precision, programmable power supplies for R&D,

test and measurement, process control, power bus simulation and power

conditioning applications across diverse industrial segments. From bench top

supplies to rack-mounted industrial power subsystems, AMETEK Programmable

Power is the proud manufacturer of Elgar, Sorensen, California Instruments and

Power Ten brand power supplies.

AMETEK, Inc. is a leading global manufacturer of electronic instruments and

electromechanical devices with annualized sales of $3.3 billion. The Company has

over 11,000 colleagues working at more than 80 manufacturing facilities and more

than 80 sales and service centers in the United States and around the world.

Trademarks

AMETEK is a registered trademark of AMETEK, Inc. California Instruments is a

trademark owned by AMETEK, Inc. Other trademarks, registered trademarks, and

product names are the property of their respective owners and are used herein for

identification purposes only.

Notice of Copyright

rights reserved.

Exclusion for Documentation

UNLESS SPECIFICALLY AGREED TO IN WRITING, AMETEK PROGRAMMABLE

POWER, INC. (“AMETEK”):

(a) MAKES NO WARRANTY AS TO THE ACCURACY, SUFFICIENCY OR

SUITABILITY OF ANY TECHNICAL OR OTHER INFORMATION PROVIDED IN ITS

MANUALS OR OTHER DOCUMENTATION.

(b) ASSUMES NO RESPONSIBILITY OR LIABILITY FOR LOSSES, DAMAGES,

COSTS OR EXPENSES, WHETHER SPECIAL, DIRECT, INDIRECT, CONSEQUENTIAL

OR INCIDENTAL, WHICH MIGHT ARISE OUT OF THE USE OF SUCH INFORMATION.

THE USE OF ANY SUCH INFORMATION WILL BE ENTIRELY AT THE USER’S RISK,

AND

ENGLISH, ALTHOUGH STEPS HAVE BEEN TAKEN TO MAINTAIN THE ACCURACY OF

THE TRANSLATION, THE ACCURACY CANNOT BE GUARANTEED. APPROVED

AMETEK CONTENT IS CONTAINED WITH THE ENGLISH LANGUAGE VERSION,

WHICH IS POSTED AT WWW.POWERANDTEST.COM.

Document and Revision

Part Number M440077-01 February 2022, Revision B

Contact Information

Telephone: 800 733 5427 (toll free in North America)

858 450 0085 (direct)

Fax: 858 458 0267

4 programmablepower.com

Email: sales[email protected]

service.[email protected]

Web: www.powerandtest.com

AMETEK Programmable Power

BPS Series User Manual - M440077-01 Rev B 5

This page is intentionally blank

6 programmablepower.com

Important Safety Instructions

Before applying power to the system, verify that your product is

configured properly for your application.

Only qualified personnel who deal with attendant hazards in power

supplies, are allowed to perform installation and servicing.

Ensure that the AC power line ground is connected properly to the Power

Rack input connector or chassis. Similarly, other power ground lines

including those to application and maintenance equipment must be

grounded properly for both personnel and equipment safety.

Always ensure that facility AC input power is de-energized prior to

connecting or disconnecting any cable.

In normal operation, the operator does not have access to hazardous

voltages within the chassis. However, depending on the user’s application

configuration, HIGH VOLTAGES HAZARDOUS TO HUMAN SAFETY may be

normally generated on the output terminals. The customer/user must

ensure that the output power lines are labeled properly as to the safety

hazards and that any inadvertent contact with hazardous voltages is

eliminated.

Guard against risks of electrical shock during open cover checks by not

touching any portion of the electrical circuits. Even when power is off,

capacitors may retain an electrical charge. Use safety glasses during open

cover checks to avoid personal injury by any sudden component failure.

Neither AMETEK Programmable Power Inc., San Diego, California, USA,

nor any of the subsidiary sales organizations can accept any responsibility

for personnel, material or inconsequential injury, loss or damage that

results from improper use of the equipment and accessories.

AMETEK Programmable Power

BPS Series User Manual - M440077-01 Rev B 7

Safety Symbols

8 programmablepower.com

Product Family: BPS Series AC Power Source

Warranty Period: 1 Year

WARRANTY TERMS

AMETEK Programmable Power, Inc. (“AMETEK”), provides this written warranty

covering the Product stated above, and if the Buyer discovers and notifies AMETEK

in writing of any defect in material or workmanship within the applicable warranty

period stated above, then AMETEK may, at its option: repair or replace the

Product; or issue a credit note for the defective Product; or provide the Buyer with

replacement parts for the Product.

The Buyer will, at its expense, return the defective Product or parts thereof to

AMETEK in accordance with the return procedure specified below. AMETEK will, at

its expense, deliver the repaired or replaced Product or parts to the Buyer. Any

warranty of AMETEK will not apply if the Buyer is in default under the Purchase

Order Agreement or where the Product or any part thereof:

is damaged by misuse, accident, negligence or failure to maintain the same as

specified or required by AMETEK;

is damaged by modifications, alterations or attachments thereto which are not

authorized by AMETEK;

is installed or operated contrary to the instructions of AMETEK;

is opened, modified or disassembled in any way without AMETEK’s consent; or

is used in combination with items, articles or materials not authorized by AMETEK.

The Buyer may not assert any claim that the Products are not in conformity with

any warranty until the Buyer has made all payments to AMETEK provided for in the

Purchase Order Agreement.

PRODUCT RETURN PROCEDURE

Request a Return Material Authorization (RMA) number from the repair facility

(must be done in the country in which it was purchased):

In the USA, contact the AMETEK Repair Department prior to the return of the

product to AMETEK for repair:

Telephone: 800-733-5427, ext. 2295 or ext. 2463 (toll free North America)

858-450-0085, ext. 2295 or ext. 2463 (direct)

Outside the United States, contact the nearest Authorized Service Center (ASC). A

full listing can be found either through your local distributor or our website,

www.powerandtest.com, by clicking Support and going to the Service Centers tab.

When requesting an RMA, have the following information ready:

•Model number

•Serial number

•Description of the problem

NOTE:Unauthorized returns will not be accepted and will be returned at the

shipper’s expense.

AMETEK Programmable Power

BPS Series User Manual - M440077-01 Rev B 9

NOTE:A returned product found upon inspection by AMETEK, to be in specification

is subject to an evaluation fee and applicable freight charges.

10 programmablepower.com

Table of Contents

1. Introduction .................................................................................... 19

1.1 General Description......................................................................... 19

1.2 Manual Organization and Format ....................................................... 19

2. Specifications .................................................................................. 20

2.1 Electrical ....................................................................................... 20

2.1.1 Input.................................................................................................................20

2.1.2 Output ..............................................................................................................21

2.1.3 AC Measurements...............................................................................................24

2.1.4 System Specification ...........................................................................................24

2.1.5 Unit Protection ...................................................................................................26

2.1.6 Mechanical.........................................................................................................27

2.2 Environmental................................................................................ 28

2.3 Regulatory..................................................................................... 28

2.4 Front Panel Controls........................................................................ 28

2.4.1 Special Features and Options ...............................................................................30

2.4.2 -HV Option Specifications.....................................................................................31

2.4.3 -LF Option Specifications .....................................................................................33

2.5 Supplemental Specifications ............................................................. 33

2.5.1 Output ..............................................................................................................33

2.5.2 Acoustic Noise Levels .......................................................................................... 33

3. Unpacking and Installation – BPS30 and BPS45 Models. ................. 34

3.1 Unpacking ..................................................................................... 34

3.2 Power Requirements ....................................................................... 34

3.3 Mechanical Installation .................................................................... 35

3.4 AC Input Connections and Wiring ...................................................... 35

3.5 AC On/Off Circuit Breaker on BPS Series front panel............................. 42

3.6 Output Connections......................................................................... 44

3.6.1 Output Wiring.....................................................................................................44

3.6.2 Output Terminal Blocks ....................................................................................... 46

3.6.3 BPS30-1, BPS45-1 -1 ø mode Output Wiring Diagram ...........................................47

3.6.4 BPS30-3, BPS45-3 3ø mode Output Wiring Diagram..............................................49

4. Unpacking and Installation – BPS75 thru BPS180 Models................ 51

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Metek Distribution d'énergie CA

Metek

Metek MX15 Manuel utilisateur

Metek

Metek TESEQ KEMA 801A Manuel utilisateur

Manuels Distribution d'énergie CA populaires d'autres marques

PS Audio

PS Audio PowerPlay 8500 Manuel utilisateur

Elgar

Elgar CW 2501P Manuel utilisateur

Panamax

Panamax M5300-PM Manuel utilisateur

Ring Powering

Ring Powering RINV500 PowerSource Manuel utilisateur

ABB

ABB System pro E power Manuel

Heath

Heath Heathkit HL-2200 Manuel utilisateur

Panamax

Panamax Powermax PM8-EX Manuel utilisateur

Furman

Furman AC-210 E Manuel utilisateur

Abtus

Abtus PWR-DA09C/P Manuel utilisateur

Belkin

Belkin PureAV PF30L Manuel utilisateur

Furman

Furman P-1800 PF Prestige Series Manuel utilisateur

EasyFocus

EasyFocus SGR-UPS5011 Manuel utilisateur

Panamax

Panamax VT1512-IP Manuel utilisateur

socomec

socomec ATyS p Manuel utilisateur

Panamax

Panamax M8DBS-EX Manuel utilisateur

Panamax

Panamax M5400-EX Manuel utilisateur

Chroma

Chroma 61501 Manuel utilisateur

Furman

Furman P-1800 AR Prestige Serie Manuel utilisateur