METALSUB TWINNINGSET Manuel de programmation
®
Nederland
Manual
METALSUB - CABLE LIGHT KL1242 - LED2400/5100
Battery Tank PR1204 / PR1209 / PR1213
Battery Tank FX1204 / FX1209
Bedieningshandleiding
TWINNINGSET
www.metalsub.nl
Dive Lights / Quick Release Systems
®NLNL
DE
ENG
Assembling manual
Montageanleitung
Montagehandleiding
1
ENGLISH 3-8
DEUTSCH 9-14
NEDERLANDS 15-20
2
English
TABLE OF CONTENTS
IMPORTANT SAFETY PRECAUTIONS!
.
.
Important safety precautions! 3
Parts 4
Assembly instructions 6
Mounting the backpack holder on the backpack 6
Assembly of the twinning set on the bottles 7
Assembly twinning set to the backpack 8
Technical information 8
Warranty 22
A.
B.
C.
D.
E.
3
Carefully read the instructions for the assembly and use of the twinning
set.
Check your buoyancy again after assembling the twinning set. The extra
weight of the twinning set could mean that you have to adjust your leas
ballast.
Always check to make sure your packpack has been properly attached
to the diving set. Secure the pressure pin with the safety spring that has
been provided for this twinning set.
Regularly check whether all attachment points are securely fastened.
After use, clean all parts with fresh water.
ENGENG
PARTS
Figure 1. Parts
Table 2. Parts list
.
Use Figure 1, 2 and Table 1 to check whether all parts are complete.
4
Photo
nr.
Part name
Amount
of parts
Order number
1 Connection plate 1 008004
2
Backpack holder
1
008202
3 Twinning plate 2 009010
4
Synthetic spacer 8mm
2
009004
5 Synthetic spacer 17mm 2 009005
6
Flat rubber packing
2
009007
7 Locking pin 1 009011
8
Self-locking nut m8
2
009985
9 Lock 2 009021
10
Concave rubber packing
2
009008
11 Pre-assembled threaded end with twinning nut 2 009031
12
Twinning band (stainless steel)
1
009071-009108
Figure 2. Twinningset explode with order numbers
008202
5
009031 009071 - 009108
009010
008004
009004
009021
009985
009005
ENGENG
ASSEMBLY INSTRUCTIONS
Charging the battery pack (fig.3)
Figure 3.
.
1.
2.
1
Mount the backpack holder at the desired height, with the pressure pin
on top. Screw the self-locking nuts on the bolts sufficiently tight without
causing distortion of the backpack if this is made of synthetic material.
Depending on the thickness of your backpack, it may be necessary to
shorten the bolts but make sure you leave enough thread for the self-
locking nut!
Choose the right packing rubber. The twinning set is supplied with two
types of rubber packing that has to be inserted between the backpack
holder and the backpack. The round one is used if the back of your
backpack is concave, use the flat one if the back of your backpack is
flat.
6
Assembly of the twinning belt on the bottles (fig. 4,5,6)
Figure 4.
1.
2.
3.
4.
5.
6.
Figuur 3
B
AA
C
Slide the twinning band to the desired height over the cylinders with the m8 nut at the
rear. Make sure that the Metalsub logo is not upside down. if necessary, first remove
the base of the bottle or the bridge.
Fig. 4: Place the two twinning plates on the twinning band. The twinning band slips into
the recess of the twinning plate.
Fig. 4A: Place the synthetic spacer in the recess left for them in the twinning plate.
Fig. 4B: Slide both threaded ends through the spacers with the pre-mounted m8 nut
and the synthetic washer on the backpack side.
Fig. 4C: Tighten the twinning nuts as tightly as you can by hand onto the threaded ends
of the bolts.
Fig. 5-6: Now alternately screw the two twinning nuts and the m8 nut tight until you
reach a tightening force of 4-7Nm for the two twinning nuts and 6-8Nm for the m8 self-
locking nut on the twinning belt.
Important: While thightening the nuts, make sure that both bottles remain flat and
parallel so no unnecessary pressure is exerted on the bridge.
Figure 5.
Figure 6.
7
ENGENG
2
55
The backpack with the fitted backpack holder can be attached to the diving set
with the mounted twinning plate quickly, firmly and easily.
The twinning plate has two raised ridges that provide a precise fit with the
recesses in the backpack holder.
The top recess of the backpack holder has a safely lock that can be operated
in a simple manner by way of a springloaded pressure pin.
1. First fit the bottom ridge into the bottom recess.
2. Push the pressure pin in completely and push the top ridge into the top
recess.
3. Release the pin. It has a groove on it that once the pin has been released
has to be completely visible.
4. Push the safety spring over the groove in the pin.
- Material: All aluminium parts are anodised in accordance with American
Military Standard MIL-A-8625-E type 3 class 2. Also the coating is
impregnated with Teflon.
- Weight above water: approx. 2,2 kg.
- Weight under water: approx. 1,5 kg.
Figure 7. Figure 8.
TECHNICAL INFORMATION
Assembly twinning set to the backpack (Fig. 7,8)
.
8
53
Table des matières
Langues :
Autres manuels METALSUB Instrument de plongée
