Messoa NCR373 Manuel utilisateur
User
Manual
201510 373 A1
IR Bullet Network Camera
NCR373
1
Table of Contents
1 Product Overview 4
1.1 Physical Characteristics 4
2 Installation 6
2.1 Package Content 6
2.2 Installation 6
2.2.1 Checking Appearance 6
2.2.2 Mounting & Wiring 7
2.2.3 Safety Wire Preparation 9
2.2.4 Adjusting the Camera Position 10
2.2.5 Adjusting the Protection Shield Hood 11
3 Connection 12
3.1 Network Topology 12
3.2 System Requirements 12
3.3 Connecting Process 13
3.3.1 Default IP address 13
3.3.2 Connecting from a computer & Viewing Preparation 13
3.4 IP Finder 17
4 Administration and Conguration 18
4.1 Live View 18
4.2 Conguration 20
4.2.1 Encode 20
4.2.2 Image 23
4.2.3 Video 27
4.2.4 Network 28
4.2.5 System 36
4.2.6 Account 40
4.2.7 Event Source 42
4.2.8 Event Handler 51
Appendix: Specications of IR Bullet Network Camera 55
2
WARNING
●This camera operates at DC 20V only.
●Installation and service should be performed only by qualied and experienced technicians and comply with all local
codes and rules to maintain your warranty.
●To reduce the risk of re or electric shock, do not expose the product to rain or moisture.
●Wipe the camera with a dry soft cloth. For tough stains, slightly apply with diluted neutral detergent and wipe with a dry
soft cloth.
●Do not apply benzene or thinner to the camera, which may cause the surface to be melted or lens fogged.
●Avoid aligning the lens with extremely bright objects (e.g., light xtures) for long periods of time.
●Although this camera is waterproof and suitable for both indoor and outdoor usages, please do not sink the camera into
water. Contact your dealer in case of sunk.
●Avoid operating or storing the camera in the following locations:
• Extremely humid, dusty, or hot/cold environments (recommended operating temperature: -40°C to +50°C)
• Close to sources of powerful radio or TV transmitters
• Close to uorescent lamps or objects with reections
• Under unstable or ickering light sources
WEEE (Waste Electrical and Electronic Equipment). Correct disposal of this product (applicable in the
European Union and other European countries with separate collection systems). This product should be
disposed of, at the end of its useful life, as per applicable local laws, regulations, and procedures.
3
FCC Compliance Statement
Information to the user: This unit has been tested and found to comply with the limits for a Class B
digital device pursuant to Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This unit generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the manual, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular installation.
If this unit does cause harmful interference to radio or television reception, which can be determined by turning the unit o
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
●Reorient or relocate the receiving antenna.
●Increase the separation between the unit and receiver.
●Connect the unit to an outlet on a circuit dierent from that to which the receiver is connected.
●Consult the dealer or an experienced radio/TV technician for help.
CE Statement
Operation is subject to the following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including interference that may cause undesired
operation. The manufacturer declares that the unit supplied with this guide is compliant with the essential
protection requirements of EMC directive and General Product Safety Directive GPSD conforming to
requirements of standards EN55022 for emission, EN 55024 for immunity.
Caution Changes or modications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the unit.
4
1 Product Overview
1.1 Physical Characteristics
Unit: mm
Figure 1 - 1: Physical Dimension & Pictorial Index
Table 1 - 1: Pictorial Index Denition
No. Name Description
1 RJ-45 Ethernet / DC Power Insert an Ethernet cable into the port for network connection and DC 20V power
supply.
2 Mounting Bracket For mounting the camera onto dierent environments, the mounting bracket is
designed with 2 axes for exible adjustment.
3 Protection Shield Hood To minimize the eects from rain and sunlight on image quality.
4 Internal Interface Cover
Open the cover so that the internal interfaces including “RESET”, “DEFAULT” button,
“Micro SD Card Slot”, etc., will be shown. More details are described as the following
gure and table. The rubber cover shall be closed after using to prevent water or
dust damage.
1
2
3
4
5
Figure 1 - 2: Internal Interface Pictorial Index
No Interface Description
A LED Indicators Blue & Red It symbolizes network data has been under transmission.
B Micro SD card slot Insert a micro SD card into the slot for recording and le storage.
C Reset & Default Button Press the button for 6 seconds to restore to the factory default settings.
Press the button for below 1 second to reboot the camera.
D Technical Debug Port This is a spared port for technician to execute specic operations if needed.
Table 1 - 2: Internal Interface Denition
6
2 Installation
2.1 Package Content
2.2 Installation
Check if everything in the packing box matches to the order form and the packing slip. All items listed below should be
included in the packing box.
•Network IR Bullet Camera * 1
•Printed Quick Guide * 1
•Guide Pattern * 1
•Plastic Anchors * 3
•Tapping Screws * 3
•Splitter Cable * 1
•Power adaptor * 1
Please contact your dealer if any of the items is lost.
Following tools might help you complete the installation:
•a drill
•screwdrivers
•wire cutters
2.2.1 Checking Appearance
When rst unboxing, please check whether if there is any visible damage to appearance of the camera and its accessories.
The protective materials used for the packaging should be able to protect the camera from most of accidents during
transportation. Please remove the protective materials of the camera when every item is properly checked in accordance
with the list in “Package Content”.
7
2.2.2 Mounting & Wiring
Step 1. Mounting Preparation
•Use the guide pattern to mark out and prepare a mounting area.
1. Place the supplied guide pattern on a mounting surface. Drill 6 mm (0.25”) outer holes x 3 at the mounting surface
corresponding to the 3 indicated positions for plastic anchors.
2. Please then hammer the 3 plastic anchors into the 3 drilled holes on the mounting surface.
Figure 2 - 1: Guide Pattern
Step 2. Mounting the Camera
1. Position the camera to match the 3 holes embedded with the plastic anchors on the surface.
2. Secure the 3 tapping screws to fasten the camera with the mounting surface tightly.
Figure 2 - 2: Mounting the Camera
This section is the preserved
area for cable entry space.
Plastic Anchors
Tapping Screws
8
Step 3. Wiring the Camera
1. While mounting the camera, pass the Ethernet RJ-45 Port cable, which penetrates from the mounting bracket, through
the hole of mounting surface or place it by the side hole of the mounting bracket as shown in Figure 2-3 depending on
your dierent applications.
Type1- Bracket Side Hole Type2 – Mounting Surface Holde
Figure 2 - 3: Placing the Ethernet RJ-45 Port cable
2. Connect the splitter cable, power adapter and Ethernet cable to the camera correctly, and connect the other end of the
Ethernet cable to the home /oce network or plugg into a home NAT/router device or an Ethernet switch, as shown in
Figure 2-4.
Figure 2 - 4: Connecting with Splitter Cable
9
2.2.3 Safety Wire Preparation
If you possess a safety wire (fall prevention wire, not supplied), connect the safety wire with one end to the mounting surface
and the other end to the safety-cord screw of the camera.
Figure 2 - 5: Mounting the Camera
Warning
Depending on the material of mounting surface, different screws and anchors than those supplied
may be required. To prevent the camera from falling o, ensure that it is mounted to a rm place using
a safety wire strong enough to withstand the total weight of the camera. (Pay also attention to the
nishing at the end of the wire.)
Caution Safety wire must be connected with one end to the surface and the other end to the safety-cord screw of
the camera. By cabling so, it is possible to prevent the camera from accidental falling at any time.
Safety wire
Safety-cord screw of the camera
Table des matières
Autres manuels Messoa Caméra IP
