Merlin 10M-E-GR Manuel utilisateur

www.merlinindustries.com

SAFETY COVER OWNER'S GUIDE

TABLE OF CONTENTS

I. Your Safety Cover:

 Construction

 SmartMesh Safety Covers

 Dura-Mesh Safety Covers

 Advanced Grade Mesh Safety Covers

 Solid Safety Covers

II. Safety Cover Accessories:

 Window Mesh Drain Panels (Solid Safety Covers Only)

 Automatic Pool Pumps (Solid Safety Covers Only)

 Padding

 Step Riser Kits

 Raised Wall Kits

 Y-Straps

 Brass Flanges

 Coping Protectors

III. Using Your Cover:

 Clogged Window Mesh Drain Panel

 Automatic Pump Not Removing Water From Cover

 Maintaining Appropriate Water Levels, 6 To 18 Inches From Cover.

 Tightening Straps

 Leaves Collecting On Safety Cover

 Water Not Collecting Near Window Mesh Drain Panel

 Water Coming Through Seams (Solid Safety Covers)

 SmartMesh Covers Collecting Water

 Coping Wear

 Spreading Of Mesh Material

IV. Closing Your Pool:

 Mesh Safety Covers

 SmartMesh Safety Covers

 Solid Safety Covers

 How To Use The Installation Tool To Install Cover

V. Opening Your Pool:

 Mesh Safety Covers

 Solid Covers

 How To Use The Installation Tool To Remove Cover

VI. Storing Your Cover:

VII. A.S.T.M Exceptions:

VIII. Non Warranty Situations:

www.merlinindustries.com

Thank you for purchasing a Merlin Industries, Inc swimming pool safety cover. Swimming pools are a fantastic form

of recreation. They give you access to a terrific form of physical activity while also bringing your family and friends

together for years of fun and enjoyment. Please use your swimming pool with the utmost care. The unique nature

of pools requires an extra level of awareness to the dangers they can present. Remember: Nothing replaces proper

supervision.

Merlin Industries, Inc. manufactures swimming pool safety covers in both mesh and solid materials. Our covers are

designed and constructed to help increase the safety level of your swimming pool and help ease the general

maintenance and care of your pool. Merlin Industries, Inc. is the original innovator of the Solid Safety Cover. No one

has made more or has more experience. Thank you for trusting your safety cover with #1.

Most installations of Merlin Industries, Inc. swimming pool safety covers meet or exceed the standards for safety

covers as established by the American Society for Testing Materials (ASTM). (Please see -exceptions on last page.)

Please review the contents of this homeowner's guide. Following these guidelines will help you and your family to

safely enjoy your pool and swimming pool safety cover for years.

Enclosed with this guide is the National Spa & Pool Institute (NSPI) pamphlet, "Layers of Protection". We urge you

to review the suggested safety options and review your own pool safety methods. Merlin Industries, Inc.

manufactures safety covers that help prevent entry into the pool, as well as safety fencing which can be used when

children or pets are present. The combination of the safety cover and safety fencing can provide you with two layers

of protection for added peace of mind. Brochures on these and other Merlin Industries, Inc. quality swimming pool

products are included in this packet.

*Note: Merlin Industries, Inc. manufactures safety covers to be as maintenance free as possible. However there is

some needed maintenance. It is up to you to follow the recommendations outlined in this owner's guide. For

example, the swimming pool water level must be maintained between 6 inches & 18 inches from the cover or the

cover warranty will be voided. Serious structural damage to the cover and/or the hardware may result. Safety

hazards are also a possibility if the water level is not maintained within this range. If you have any questions contact

your dealer or visit us at www.merlinIndustries.com.

I. YOUR COVER

Construction:

All Merlin Industries, Inc. safety covers are designed to formfit to the shape of the pool for which they are made.

Rectangular safety covers should not be used on anything but rectangular pools and a safety cover must be used

on the pool for which it was designed. Failure to follow these rules will void the warranty. The overlap on a rectangle

swimming pool can vary from 10 inches to 18 inches. For free-form pools this overlap can vary from 12 inches to 24

inches. In the case of an obstruction, rock walls or waterfalls for example, the cover can be cut flush at these areas.

It is the grid of webbing that allows the safety cover to be stretched taut across the pool and provides the cover with

its strength.

SmartMesh Covers:

SmartMesh Safety Covers utilize a high tech weave that allows water to pass through the material and still provides

100% shade to reduce the chance of algae growth. If water should accumulate on the cover, it is necessary to

remove it and clean the cover using the techniques described in the "Using you Cover" section of this guide.

Merlin's patent number for SmartMesh is US 6,886,187 B2. 1

www.merlinindustries.com

The SmartMesh safety cover meets or exceeds all standards for safety covers as established by the American

Society for Testing Materials (ASTM)*. The SmartMesh safety cover comes with a limited pro-rated 15-year

warranty, which warranties against manufacturer's defects. Refer to your warranty card.

Dura-Mesh Safety Covers:

The weave of the mesh safety cover is designed to allow water to drain through the cover and to prevent large

debris and particles from passing through the safety cover and entering into the pool. The cover allows some fine

silt and/or dust to enter the pool. Some sunlight is also allowed into the pool.

The standard mesh safety cover meets or exceeds all standards for safety covers as established by the American

Society for Testing Materials (ASTM)*. The Dura-Mesh safety cover comes with a limited pro-rated 15-year warranty,

which warranties against manufacturer's defects. Refer to your warranty card.

Advanced Grade Mesh Safety Covers:

The weave of the advanced grade mesh safety cover is designed to allow water to drain through the cover and

prevent large debris and particles from passing through the cover and entering the pool. The weave of the

advanced grade mesh safety cover is approximately 50% tighter and thicker than the weave of the standard mesh

safety cover. This cover allows a reduced amount of fine silt and/or dust to enter the pool. A reduced amount of

sunlight is also allowed into the pool.

The Advanced Grade Mesh safety cover meets or exceeds all standards for safety covers as established by the

American Society for Testing Materials (ASTM)*. The advanced grade mesh safety cover comes with a limited pro-

rated 20-year warranty, which warranties against manufacturer's defects. Refer to your warranty card.

Solid Safety Covers:

The solid cover with an automatic pump does not allow any debris, fine silt and/or dust, or sunlight to enter the pool

through the cover. The solid cover with a window mesh drain panel may allow a very small amount of particulate

matter to enter the pool through the 2 layers of micro-mesh filter. The solid safety cover must have a properly

working automatic pump or a properly working window mesh drain panel on the cover at all times to meet ASTM*

standards.

The solid safety cover meets or exceeds all standards for safety covers as established by the American Society for

Testing Materials (ASTM)*. The solid safety cover comes with a limited pro-rated 10-year warranty, which

warranties against manufacturer's defects. Refer to your warranty card.

* When safety cover is properly installed

II. SAFETY COVER ACCESSORIES

Window Mesh Drain Panel for Solid Safety Covers:

Solid safety covers can come with a "Window Mesh Drain Panel" to remove water from the top of the cover in lieu of

an automatic cover pump. The window mesh drain panel is a removable square piece of 250-micromesh material

attached to a square piece of standard mesh material. The panel is applied to the top of the cover with Velcro for

easy removal.

The drain panel is placed where the water on the cover will drain the quickest. During installation the cover needs to

be adjusted so the water will be "directed" toward the panel for drainage purposes. The adjustment will require

tightening and loosening of some straps to achieve maximum effectiveness. 2

www.merlinindustries.com

Automatic Cover Pump for Solid Safety Covers:

Solid safety covers can come with an automatic cover pump to remove water from the top of the cover in lieu of a

window mesh drain panel. The pool pump should be placed at the lowest point of the cover or where the water

accumulates. The pool pump is required to stay on the cover, and be plugged in, whenever the cover is in place. It

is designed to withstand snow and/or freezing conditions.

The pump is equipped with a pressure activated pneumatic float switch, which will automatically turn the pump on

at the 2 inch to 3-inch water level. Once activated the pump will pump until the water level is at the lowest pump

level. When attaching the garden hose to the pump make sure that you have a long enough run of hose so the

water does not end up back on the cover or the pool deck. Place the end of the hose far enough away from the

pool so the water does not saturate the ground around the pool. In the event that the pump does not perform refer

to pump owners manual found in the pump box or contact your local service dealer.

Padding:

On many pools, step sections and swim out sections create "reverse corners" or "sharp edges" inside the pool.

These sharp edges need to be padded to prevent wearing of the cover in these locations. This padding is attached

directly to the underside of the cover and is sewn on with the same webbing used to put the cover together. When

the cover is installed the padded sections of the cover should fall directly over any reverse corners inside the pool.

Some very sharp corners and rough coping may require additional padding. Please consult with your dealer for

further information

Step Riser Kits: (optional)

Step riser kits are designed to close or fill the triangular gaps created when a safety cover is installed to go up and

over a raised wall area. Step riser kits are installed at the job site during the initial installation. They are designed to

prevent small children, pets, or leaves and debris from entering the pool. Failure to install a step riser kit when one

is required will result in a safety hazard and will VOID ASTM safety approval.

Raised Wall Kit: (optional)

Raised wall kits are designed to secure a safety cover to a pool with a raised wall or beam. The kit is applied directly

to the raised wall or beam using a stainless steel cable assembly and eyebolts that are installed during initial

installation. Failure to install a Raised wall kit when one is required will result in a safety hazard and will VOID ASTM

safety approval.

Center Harness Strap Kit: (optional)

Center harness strap kits, or "Y" straps, are designed to be installed on a cover with an obstruction that does not

come in contact with the cover, but has a strap that runs into it. This strap kit creates a Y-strap to go on either side

of the obstruction. An example of an obstruction may be a dive stand.

Coping Clips: (optional)

Coping Clips fit underneath the cover and act as a buffer between the cover wear bars and the coping to prevent

wear and/or discoloration to the coping. Coping Clips slip onto the coping and are tied to the brass anchor or strap

behind the wear bar.

Brass Flanges: (optional)

Brass Flanges or beauty rings, fit over your brass anchors, are flush with the deck and are used to give a more

finished look or to hide any chipping that may occur during initial installation 3

www.merlinindustries.com

III. USING YOUR COVER

Merlin Industries, Inc. strongly suggests that a qualified pool professional complete the initial installation of the cover.

Improper installation of the cover can result in the warranty being voided.

Upon installation the cover should be taut across the pool. The springs on a mesh safety cover should be

compressed approximately 50% and between 60% to 75% for solid safety covers and should not be removed

without the aid of the installation tool. Should the cover not be taut, the straps can be adjusted and tightened.

(See Below).

Although the cover will support an adult's weight, we do not recommend walking on the cover except when cleaning

the window mesh drain panel or clearing debris from around the automatic pump. Do not walk on the edge of the

cover to avoid excessive cover wear.

Clogged Window Mesh Drain Panel for Solid Covers:

Remove the window mesh drain panel from the cover by grasping one corner and pulling the velcroed panel off the

cover. With a garden hose spray the underside of the mesh panel to remove all debris and spray the cover's filter

panel. Reattach panel.

Pump not pumping:

Check the electrical source for the pump. Check for excess debris around the base of the pump. Refer to the pump

owner's manual.

Checking water level for mesh and solid:

In order to ensure that the water level of the pool does not rise above 6 inches or fall below 18 inches from the cover,

remove a spring at a convenient corner of the pool and pull cover back to view the water. Should the water level be

more than 18 inches from the cover, add water with a garden hose to the appropriate level. Should the water level

be less than 6 inches from the cover, place a water pump on the first step of your stair section and pump the water

down to the correct level.

*Note: The swimming pool water level must be maintained between 6 inches & 18 inches from the cover or the

cover warranty will be voided. Serious structural damage to the cover and/or the hardware may result. Safety

hazards are also a possibility if proper water levels are not maintained.

Tightening straps:

In the event the springs are not compressed 50% for mesh covers and between 60% to 75% for solid covers, or the

straps become loose, the straps should be tightened. Loose straps can cause premature cover wear. Remove the

spring from the anchor with the installation tool. Using the strap and buckle, adjust the length of the strap by 2 inch

increments and reinstall the spring on the anchor using the installation tool until the spring is compressed 50% for

mesh covers and 60% to 75% for solid covers and the straps are snug.

Leaves collecting on cover:

Leaves collecting on the cover are a normal circumstance. Simply allow them to dry and blow off. Should you find

that the leaves tend to collect on the cover ensure that the straps are taut across the pool to allow the leaves to blow

away.

www.merlinindustries.com

Water not collecting near panel of solid cover:

In the event that water seems to collect in an area of the cover that does not have a window mesh drain panel, the

straps of the cover can be adjusted to direct the water towards the drain panel for proper drainage.

Step 1: Loosen the four straps that border the window mesh panel.

Step 2: Tighten the straps that are outside or surrounding the accumulation of water.

Step 3: The water might need assistance to begin moving towards the panel. Try to temporarily depress the cover

near the panel to help the flow of water towards it. In some situations you may need to add some weight to that area

of the cover.

Step 4: Wait 2 to 3 days to allow the cover to "tighten" then flood the cover with a garden hose to check that the

cover drains properly on its own.

Step 5: Repeat above steps as needed.

Water Coming Through Seams (Solid Safety Covers):

You may notice that water will pass through the seams of a solid cover. This is due to our normal manufacturing

process, and is inherent in all Solid Safety Covers. Taut Solid Safety Covers are held together and given their

strength by the webbing which is sewn in place. Water may pass through the needle holes formed by this process.

THIS IS NOT A DEFECT IN THE COVER. Over time, these needle holes will become "clogged" by the expansion

of the thread when it becomes wet, and by small debris particles that become lodged in the holes.

SmartMesh Cover Collecting Water:

In areas where large amounts of pollen, dirt, leaves or other debris clog the openings of a SmartMesh cover, it will

be necessary to clean the cover. While on the pool use a nylon bristle pool brush to dislodge the debris and allow

water to pass through. If the cover is dry, a leaf blower may be used to blow the debris off the cover or spray

through the backside of the cover with a garden hose or LOW power pressure washer. NOTE: HIGH PRESSURE

POWER WASHING MAY DAMAGE YOUR COVER. DO NOT USE HIGH PRESSURE POWER WASHERS OR

HIGH PRESSURE POWER WASHER TIPS.

Cover Chafe or Coping Wear:

Cover Chafe or coping wear is NOT a manufacturing defect and is NOT covered under the warranty. It can be

caused by many things, including, but not limited to the following…

PROBLEM  SOLUTION

Loose cover Adjust straps to tighten cover.

Rough coping Smooth coping by removing any burrs or small pebbles.

Pad coping with carpeting or some other non-abrasive substance.

Padding is also available through your dealer from Merlin Industries, Inc.

Windy area Adjust straps to tighten cover.

Padding may also be needed (Available as an option, and can be added).

Spreading of Mesh Material:

Like the strings of a tennis racket, the strands of the mesh material can be moved back into position by rubbing the

material with your fingers. Rub the cover between your fingers gently. Remember to avoid pulling on the mesh

material when moving the cover. When moving the cover always use the straps to pull the cover.

www.merlinindustries.com

IV. CLOSING YOUR POOL IN THE FALL

The cover should be checked for any damage that may have occurred during storage. Never raise the deck

anchors prior to reinstallation, as damage may occur by dragging the cover over raised anchors. Keep anchors

flush until the cover is positioned correctly over the pool. When moving or handling the cover, never grab the

paneled material; always move the cover by using the reinforced webbing and straps. Water level in the pool must

be between 6 inchesand 18 inches below the cover at all times or the warranty will be voided.

Mesh Cover:

Check with your pool dealer for water treatment prior to putting the cover on the pool. Once the cover is on the pool,

do not add chemicals through the cover always lift one corner and add chemicals accordingly. If chemicals do get on

your cover, rinse immediately with large volumes of water. To help assure you open your pool to clear water, it may

be necessary to add chlorine and/or algaecide (40% to 60% "quat" algaecide) 2-3 times in the spring, prior to

opening your pool. Consult with your pool dealer for appropriate dosages.

SmartMesh Cover:

To help ensure a clean and algae free pool at opening, a SmartMesh covered pool MUST be clean, algae free with

the water balanced and proper winterizing chemicals added. SmartMesh provides 100% shade but is only one part

of having a clean and algae free pool. Failure to properly follow the above instructions may lead to an algae and or

debris problem when the pool is opened.

Failure to remove debris and leaves from the top of your SmartMesh cover can also lead to an unpleasant opening

in the spring. Debris and leaves usually blow off the cover with normal winds. If this does not happen you can

remove leaves and debris with your pool brush or a leaf blower. When leaves and debris are left on the cover, they

can begin to decay and can "steep" when water drains through the cover. This "steeping" will effect the pool water

similar to how a tea bag effects water when brewing tea.

Solid Cover:

Check with your pool dealer for water treatment prior to putting the cover on the pool. Once the cover is on the pool,

do not add chemicals through the cover always lift one corner and add chemicals accordingly. If chemicals do get on

your cover, rinse immediately with large volumes of water. Weeping or dripping of water through the stitching of a

solid safety cover is normal and should diminish over time.

Note: Observation of your cover pump is necessary to prevent accidental draining of your pool. Also, heavy rain or

snow load may displace some water in your pool. It may be necessary to add water to the pool over the course of

the winter. Keep your water level between 6" and 18" below the cover.

How to use the Installation Tool to install cover:

Using the allen wrench, raise the threaded portion of the brass anchor approximately ¼". Slip the installation tool

through the round end of the stainless steel spring. Stand facing the pool and place the installation tool over the

brass anchor with the notched end facing the pool. Using your body for leverage, pull the top of the installation tool

away from the pool seating the spring on the brass anchor. You may want to gently step on the spring as it slides

down the installation tool. Twist the installation tool to cause the notched area to line up with the back of the spring.

www.merlinindustries.com

V. OPENING YOUR POOL

The cover should be checked for any damage that may have occurred during the winter season. If any problems

have occurred, contact your Merlin Dealer for repair procedures. General repairs are not made by Merlin Industries

between July 1st and December 15th. Never leave the deck anchors raised when removing the cover as damage

may occur by dragging the cover over raised anchors. When moving or handling the cover, never grab the paneled

material; always move the cover by using the reinforced webbing and straps.

Mesh Cover:

A fine silt or sediment may be visible on the bottom of the pool. Vacuum to waste and allow your filter to run. Add

opening chemicals according to your pool dealer's recommendations. If chemicals get on your cover rinse

immediately with large volumes of water.

Solid Cover:

A fine silt or sediment may be visible on the bottom of the pool for pools with a window mesh drain panel. Vacuum to

waste and allow your filter to run. Add opening chemicals according to your pool dealer's recommendations. If

chemicals get on your cover rinse immediately with large volumes of water.

How to use the Installation Tool to remove cover:

Stand outside of the anchor, away from the pool, facing the cover. Place the installation tool into the round end of

the spring with the notch facing away from the pool. Position the tool between the anchor and the spring, lean it

forward towards the pool. This will unseat the spring.

VI. STORING YOUR COVER

Before storing your Merlin cover, remove all leaves and debris from the cover's surface. Simply spray with hose and

gently brush to loosen dirt. Check the cover prior to storage for excessive wear or damage that may have occurred

during the winter. Covers do not need to be dried prior to storage. Fold cover and store in mesh bag included with

your cover order. Merlin recommends hanging the cover far enough off the ground to avoid damage by mice and

other rodents. Never place the cover near chemicals or a heat source as excessive heat can melt the cover.

Removal of the springs vs. leaving them on is an option that is up to you.

SmartMesh Covers

When cleaning your cover prior to storage, spray the cover with a garden hose or LOW power pressure washer from

its underside to dislodge any pollen or fine debris caught in the mesh material.

NOTE: HIGH PRESSURE POWER WASHING MAY DAMAGE YOUR COVER. DO NOT USE HIGH PRESSURE

POWER WASHERS OR HIGH PRESSURE POWER WASHER TIPS.

VII. A.S.T.M. EXCEPTIONS*

More than 25% of the safety cover requires lawn stakes or aluminum tubes.

No step riser kit installed when required.

No gap filler installed when required.

No cable assembly installed when required.

A solid cover that does not have a pool pump or window mesh drain panel in proper working order, or does not have

either water removal system present. 7

www.merlinindustries.com

VII. A.S.T.M. EXCEPTIONS* CON'T.

Covers being installed on pools they were not designed for.

Damaged cover.

Improper installation.

VIII. NON - WARRANTY SITUATIONS*

Coping wear. - When the pool's edge wears though the cover or cover pads.

(Additional padding can be purchased to help avoid this)

Acts of God.

Improper installation.

Water levels not maintained between 6" and 18" below cover.

Wear due to a cover being installed on a pool for which it was not designed.

*The above situations are some, but not all, of the situations that are not covered under the warranty and that will

cause a cover to not meet A.S.T.M. standards. If you have any questions about your cover contact your dealer or

visit us at…www.merlinindustries.com

ALL INQUIRIES REGARDING YOUR COVER SHOULD BE MADE TO YOUR DEALER OR INSTALLER.

IF YOU ARE UNABLE TO CONTACT YOUR DEALER FOR ANY REASON, MERLIN INDUSTRIES CAN BE

CONTACTED VIA EMAIL OR MAIL.

MAIL TO : MERLIN INDUSTRIES, INC.

2904 EAST STATE STREET EXT.

HAMILTON, NJ 08619

EMAIL TO: [email protected]

ALL INQUIRIES SHOULD INCLUDE:

DATE OF PURCHASE

SERIAL NUMBER

DEALER OR INSTALLER NAME AND LOCATION

PICTURES OF ISSUE

CUSTOMERS CALLING MERLIN INDUSTRIES, INC. DIRECTLY WILL BE DIRECTED TO CONTACT US VIA ONE

OF THE TWO METHODS ABOVE.

Retain for your records:

Purchase Date __________________________________________________

Dealer  __________________________________________________

Serial Number __________________________________________________ 8

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Merlin Équipement d'éclairage

Merlin

Merlin myQ 827AU Manuel utilisateur

Manuels Équipement d'éclairage populaires d'autres marques

Brizo

Brizo 8SP-MU-4 Manuel utilisateur

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manuel utilisateur

IKEA

IKEA BJÖRKSPIREA Manuel utilisateur

Laserworld

Laserworld Evolution Series ES-400RGB Manuel utilisateur

Alien

Alien RG STAR Manuel utilisateur

EuroLite

EuroLite LED B-40 Manuel utilisateur

Qazqa

Qazqa Suplux SL 3 Black 103062 Manuel utilisateur

Commercial Electric

Commercial Electric 54568141 Manuel utilisateur

CREE LIGHTING

CREE LIGHTING 304 Series Manuel utilisateur

Goobay

Goobay 49867 Manuel utilisateur

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manuel utilisateur

Alkalite

Alkalite Krypton KT-81 Manuel utilisateur

Clas Ohlson

Clas Ohlson GU10 Manuel utilisateur

DTS

DTS DELTA 10 F Manuel utilisateur

ring

ring Solar Steplight Manuel utilisateur

One Stop Gardens

One Stop Gardens 57696 Instructions de montage

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manuel utilisateur

SIREM

SIREM Swimeo A2 Manuel utilisateur