Meritor 17X Manuel utilisateur

Maintenance Manual MM-0700

Single Reduction Differential Carrier

17X

Revised August 2017

2Meritor Differential Carrier 17X

Service Notes

Before You Begin

This publication provides installation and maintenance procedures

for the Single Reduction Differential Carrier 17X produced by

MERITOR VS.

The information contained in this publication was current at the

time of printing and is subject to revision without notice or liability.

You must understand all procedures and instructions before you

begin maintenance and service procedures.

You must follow your company's maintenance and

service guidelines.

You must use special tools, when required, to avoid serious

personal injury and damage to components.

Meritor uses the following notations to alert the user of possible

safety issues and to provide information that will help to prevent

damage to equipment and components.

WARNING

A WARNING indicates a procedure that you must follow

exactly to avoid serious personal injury.

CAUTION

A CAUTION indicates a procedure that you must follow

exactly to avoid damaging equipment or components.

Serious personal injury can also occur.

NOTE: A note indicates an operational, procedure or instruction

that is important for proper service. A NOTE can also supply

information that will help to make service quicker and easier.

This symbol indicates that you must tighten fasteners to a

specific torque.

Information contained in this publication was in effect at the time the publication

was approved for printing and is subject to change without notice or liability.

Meritor Commercial Vehicle Systems reserves the right to revise the information

presented to discontinue the production of parts described at any time.

Access Information on Meritor's Web Site

Additional maintenance and service information for Meritor's

commercial vehicle systems component lineup is also available at

www.meritor.com visiting the “Literature on Demand” page.

No part of this publication may be reproduced in any form or by any means or

granted to any third parties without thewritten permission of MERITOR.

MERITOR reserves the right to publish revisions at any time for technical or

commercial purposes. Therefore all material contained in this manual is based on

the latest information available at time of publication approval.

Document No. MM-0700

Revision: August 2017

Meritor Differential Carrier 17X

Contents

05 Section 1: Introduction

07 Specification & Data

08 Exploded View

09 Exploded View Parts List

10 Section View

11 Section View Parts List

13 Section 2: Maintenance

14 Differential Removal & Installation

14 Checking the Rear Axle ousing

15 Ring Gear & Pinion Adjustment

16 Shim Pack Calculation

18 Carrier Assembly

22 Calculating the Preload Spacer

29 Adjust Differential Bearings Preload

31 Tooth Contact Patterns & ypoid Gear Set

36 Installation & Adjustment of the Diff Lock Sensor Switch

39 Section 3: Hypoid Gear Patterns

40 ypoid Gear Pattern Tables

43 Section 4: Pinion Seal Replacement

44 Disassembly

45 Assembly

47 Section 5: Differential Lock Removal

48 Differential Lock Removal

49 Section 6: Tightening Torque Values

& Lubrication

50 Torque values

51 Tightening Torque Table

53 Section 7: Troubleshooting

54 Troubleshooting Chart

pg. 55 Section 8: Service Tools

56 CT01 - Pinion Pac Oil Seal keying Tool

57 CT03 - Input Flange Wrench

58 CT05 - Spigot Bearing keying Tool

59 CT06 - Spigot Bearing Pinion keying Tool Punch

60 CT12 - Adjusting Ring Wrench

61 CT40 - Inner Pinion Bearing measuring Tool

62 CT42 - Inner Bearing Cup Tool

63 CT43 - Outer Bearing Cup Tool

64 CT44 - Inner Bearing Cone Tool

65 CT45 - Outer Bearing Cone Tool

66 CT46 - Diff. Bearing Cone L/ Tool

67 CT47 - Diff. Bearing Cone R/ Tool

68 CT48 - Diff. Lock Spring compression Tool

69 CT49 - Diff. Lock Spring fitting Tool

70 CT50 - Pinion Spacer Pre-Set Nut Tool

71 CT51 - Pinion Spacer Pre-Set Nut Flange

72 CT52 - Diff. Crown Wheel lifting Tool

73 CT53 - Punch-Tool (Axle Shaft)

74 MST4713 - Adj. Ring Wrench Assy L. .

75 MST4714 - Adj. Ring Wrench Assy R. .

pg.

4Meritor Differential Carrier 17X

Terms used in this manual

Manufacturer:

MERITOR

Manual:

Maintenance manual no. MM-0700

Device:

Single Reduction Differential Carrier 17X

Technician:

Qualified personnel working on the Single Reduction Differential

Carrier maintenance and servicing.

Maintenance and servicing:

Maintenance and servicing refer to periodical checks and/or

replacement of the Differential Carrier or components. It also

refers to the determining of the cause of a malfunction in order to

restore the initial operating conditions.

Operator:

Any person who will use the Single Reduction Differential Carrier

as part of a more complex device.

Warranty

Warranty applies to the Single Reduction Differential Carrier

installed on vehicles for which it was designed. Warranty is void in

the following cases:

• Improper use of the vehicle on which the Single Reduction

Differential Carrier is installed (usage conditions, overloading etc.)

• Tampering with vehicle components that may affect the Single

Reduction Differential Carrier assembly performance.

• Use of non-original spare parts.

• Improper installation, adjustment, repair or modification.

• Poor or improper maintenance (including consumables other

than those specified).

Further information on warranty conditions may be obtained

directly from the manufacturer or by referring to the Meritor web

site www.meritor.com

Meritor Differential Carrier 17X

pg.

Introduction

07 Specification & Data

08 Exploded View

09 Exploded View Parts List

10 Section View

11 Section View Parts List

6Meritor Differential Carrier 17X

1Introduction

General description

The differential unit is of the single-reduction type featuring a

hypoid gear set. The bevel pinion is mounted on two taper roller

bearings and a third straight roller bearing. The bevel pinion

setting relative to the drive gear can be adjusted by varying the

thickness of the shim pack located between the inner pinion

bearing cup and the carrier bearing shoulder. The differential

assembly drive gear welded is supported on two taper roller

bearings and is adjusted for end play through two threaded ring

nut adjusters.

Specifications and data

Hypoid pinion bearings

2 taper roller and 1 straight roller bearing

Differential unit

Final Drive ypoid Gear Ratio (and bevel set teeth)* 2.64 (14/37): 2.85 (13/37): 3.08 (12/37): 3.36 (11/37): 3.70

(10/37): 4.11 (9/37): 4.33 (9/39): 4.63 (8/37): 5.29 (7/37):

5.63 (8/45): 6.17 (6/37)

Pinion to Drive Gear Backlash 0.26 ÷ 0.50 mm

Pinion to Crown Backlash Adjustment Adjusting Rings

Differential Bearing Cap Divergence 0.15 - 0.33 mm

Differential Bearing Cap Divergence Adjustment using the Ring Nut Adjusters

Thickness Range for the Shims fitted between the

Bevel Pinion Bearing Cage & the Differential Carrier 0.10 - 0.15 - 0.20 - 0.50 mm

Drive Gear runout 0.20 max mm

Pinion Bearing Preload 0.50 - 10 Nm without Pinion Seal

* Verify with the Engineering reference the range of the ratio in current production because sometimes some ratios could be already

released but not currently in production.

Meritor Differential Carrier 17X

1Introduction

8Meritor Differential Carrier 17X

1Introduction

Exploded view

Fig. 1.1

Input Flange & Deflector Option Diff Lock Cover Option No Diff Lock Option

16 15a-1

15b-1

9a 32

10b

22-1

15a-2

15b-2 22-2 23

24-2 31

10a

Meritor Differential Carrier 17X

1Introduction

Exploded view Parts list

Ref. Description

Diff Carrier & Cap Assembly

1a Diff Carrier

1b Bearing Cap R (Disjoint)

1c Bearing Split Cap L

1d Capscrew - Bearing Cap R

1e Capscrew - Bearing Cap L

1f Washer - Bearing Cap Capscrew

1g Locator Pin

Differential Gear Set Assembly

2a Drive Pinion

2b Diff Assembly & Drive Gear - Welded

Diff Bearing L Side

3a Diff Bearing Cup L

3b Diff Bearing Cone L

Diff Bearing R Side

4a Diff Bearing Cup R

4b Diff Bearing Cone R

Adjusting Ring R Side

Adjusting Ring L Side

Lock - Adjusting Ring

Capscrew - M6 x 20

Outer Pinion Bearing

9a Outer Pinion Bearing Cup

9b Outer Pinion Bearing Cone

Inner Pinion Bearing

10a Inner Pinion Bearing Cup

10b Inner Pinion Bearing Cone

Spacer (Variable)

Shim - Inner Pinion Bearing Cup (0.10mm)

Shim - Inner Pinion Bearing Cup (0.15mm)

Shim - Inner Pinion Bearing Cup (0.20mm)

Shim - Inner Pinion Bearing Cup (0.50mm)

Ref. Description

Spigot Bearing

Pinion Seal

Companion Flange & Deflector Assy

15a - 1Companion Flange (option 1)

15b - 1Deflector (option 1)

15a - 2Input Flange (option 2)

15b - 2Deflector (option 2)

Pinion Nut - M45

Shift Fork

Shift Shaft

Piston (optional)

“O”Ring (40mm diameter)

Shift Shaft Spring

22 - 1 Diff Lock ole Cover (option 1)

22 - 2 Diff Lock ole Cover (option 2)

Gasket

ex ead Capscrew - M6 x 20

24 - 2 Countersunk ead Capscrew - M6 x 20

Washer (optional)

Clutch Shift Collar

Lock-Nut - Sensor Switch

Sensor Switch

ole - End Plate Cover

Blanking Plug - Sensor Switch ole

Washer - Plug

Identification Plate

10 Meritor Differential Carrier 17X

1Introduction

Section view

Fig. 1B

Right

Bearing Cap

Left

Bearing Cap

Table des matières

Autres manuels Meritor Équipement industriel

Meritor

Meritor MM-0170 Manuel utilisateur

Meritor

Meritor RS 120 Manuel utilisateur

Meritor

Meritor TP-9579 Manuel de service

Meritor

Meritor LM Series Manuel utilisateur

Meritor

Meritor 18X Manuel utilisateur

Meritor

Meritor Meritor ELSA 195 Manuel utilisateur

Meritor

Meritor 3000 Series Manuel utilisateur

Meritor

Meritor MM-0861 Manuel utilisateur

Meritor

Meritor TM Series Manuel utilisateur

Meritor

Meritor T-2111 Series Manuel utilisateur

Meritor

Meritor PreSet Manuel utilisateur

Meritor

Meritor RS-220 Manuel utilisateur

Meritor

Meritor MM-2075 Manuel utilisateur

Meritor

Meritor RS 120 Manuel utilisateur

Meritor

Meritor MORH2P035 Series Manuel utilisateur

Meritor

Meritor MTC Series Manuel utilisateur

Meritor

Meritor MTC-4208X Series Manuel utilisateur

Meritor

Meritor MM-0164 Manuel utilisateur

Meritor

Meritor MM-96147 Manuel utilisateur

Meritor

Meritor 13X Series Manuel utilisateur

Meritor

Meritor MM-0164 Manuel utilisateur

Meritor

Meritor MS-113 Manuel utilisateur

Manuels Équipement industriel populaires d'autres marques

ABB

ABB Unifix AD Manuel

Mark 7

Mark 7 Evolution Manuel utilisateur

Husky

Husky HyPET Manuel utilisateur

bora

bora PM-1800 Manuel utilisateur

Grizzly

Grizzly T32428 Manuel utilisateur

Siemens

Siemens 8MF1 Series Manuel utilisateur

ABB

ABB HT610965 Manuel utilisateur

ABB

ABB SafeLink Manuel utilisateur

Phoenix

Phoenix PHX-150 Manuel utilisateur

ABB

ABB A165-L32 Manuel utilisateur

ABB

ABB HT842936 Manuel utilisateur

Rioned

Rioned UrbanJet Manuel utilisateur

Hermetica

Hermetica 10 Series Manuel utilisateur

HORNER

HORNER OEE Solution Manuel utilisateur

Hammerhead

Hammerhead HG375 Manuel utilisateur

SCHUNK

SCHUNK VERO-S NSE-A3 138 Instructions d'utilisation

ABB

ABB HT566657 Manuel utilisateur

Webasto

Webasto GSE CAN Manuel utilisateur