Menvier DC58 Mode d'emploi

DC58 & DC58M Installation &DC58 & DC58M Installation &

Programming Guide OverviewProgramming Guide Overview

General

The DC58/58M digital communicator consists of a

single PCB fitted in a small polycarbonate case. It is

used to transfer status information from an alarm

system to a dedicated Alarm Receiving Centre (ARC)

via the Public Switched Telephone Network (PSTN). The

DC58MoffersthesamefeaturesastheDC58butitalso

functions as a V21 modem. The DC58M is required

when using the up/downloading feature on

compatible Menvier Security control panels.

Operating Modes

The DC58 can be used as a stand-alone

communicator, in this mode the communicator is

hard-wired to the control panel using the appropriate

terminal block connections. Alternatively the unit can

be plugged on to a suitable Menvier Security control

panel, such as the TS510, TS700, TS790, TS900, TS2500

or TS2200. When used in this mode the communicator

plugs on to the control panel using the lead supplied.

The DC58M can only be used in the plug-on mode.

NVM Programming

All programmed data is stored in a plug-in NVM

(Non-Volatile Memory) which will be retained for up to

five years with no power present. The NVM can be

programmed by using a Menvier Security LCD Remote

Keypad (P/No. NETLCD) and an engineer's interface

lead (P/No. NETEKI) which will plug directly on to the

DC58/58M.AlternativelytheNVMcanbeprogrammed

using the desktop programmer PP5.

Your ARC will normally provide a programming service

and will supply a pre-programmed NVM on request.

Technical Specifications

Supply: 11.5V - 14V; 35mA dc (Standby);

100mA dc (Active)

The installer must ensure that

power drawn by the DC58/58M

plusanyotherauxiliaryapparatusis

within the rating of the control

panel (host) power supply.

Low Battery: Detection threshold is at 10.8V +/-

0.2V

Outputs: [1+]: Switched +ve @100mA

[2-]: Switched -ve @100mA

Ch1-8: Maximum input voltage 28V.

Channel input trigger either +ve or

-ve applied (JP3)

Modem: 300 Baud (V21)

Programmer: NETLCDremote keypad& NETEKIor

PP5.

Case Size: 142(w) x 82(h) x 36(d) mm.

Weight 265g

REN value: 0.0

BT Approval: DC58 - S/1100/3/R/503310

DC58M - S/1100/3/R/503311

Series Voltage Drop

The voltage drop introduced by the series connection

throughtheDC58/58Matalinecurrentof40mAis0.1V.

When used with other apparatus (telephone, fax etc.)

thetotalvoltagedrop@40mAMUSTNOTexceed2.0V.

496545 Issue A 1of8 DC58 & DC58M

DC58 & DC58M

Plug-on Mode

Stand-alone Mode

(DC58 Only)

erminal

connections for

other control

panels NETLCD Remote Keypad

(Programmer)

NETLCD Remote Keypa

(Programmer)

Plug-on to

Menvier Security

control panels

Figure 1. Operating Modes

Installation

1 Output 2- (SELV)

Programmable switched -ve output rated

@100mA.

2 Output 1+ (SELV)

Programmable switched +ve output rated

@100mA.

3 Power Input (SELV)

12V power input, only use in stand-alone mode.

4 CH1 - CH8 (SELV)

Inputchannels1-8,onlyuseinstand-alonemode.

5 JP5

Input channel trigger polarity, stand-alone mode

only.

[+] = +ve applied (0V going to 12V)

[-] = -ve applied (12V going to 0V)

6 LED 1

Activity LED. On whilst communicator is active.

Flashes on and off 4 times when successfully

communicated with the ARC. Flashes continuously

when modem is in operation.

7 Test Call

Short these two pins to initiate a test call.

8 NVM

Removable Non-Volatile Memory used to store all

programmed data.

9 JP2 (SELV)

Connector for Menvier Security control panels.

10 JP1 (SELV)

Connector to NETLCD/TS900 remote keypad

(Programmer).

11 Telephone Connections (TNV)

Terminal connections to the telephone line.

12 HI/LO SECURITY

Line fault monitoring level:

Link fitted = High Security (Line Out, Incoming

Ringing, Line Voltage)

Link removed = Low Security (Line Cut only)

DC58 & DC58M

DC58 & DC58M 2of8 496545 Issue A

CH1CH2CH3CH4CH5CH6CH7CH8

12V 0V 1+ O/P 2-

A1 B

B1 BC

NVM

TEST

JP5

Trig

Polarity

TS900

REMOTE

TO CONTROL

PANEL

JP2

JP1

HI/LO

SECURITY

4 5

Figure 2. DC58 PCB Layout

A1 B

TS900

REMOTE

CONTROL

PANEL

HI/LO SECURITY

TEST

CALL NVM

67812

JP 2

JP1.

Figure 3. DC58M PCB Layout

Plug-on Installation

1. Isolate ALL power from the control panel (battery

and mains).

2. Do not attempt to continue if the mains or battery

supply is still present.

3. Remove the cover from the DC58/58M case and if

appropriate fit a pre-programmed NVM.

4. Connect the interface lead to the control panel

connector(DIGIMODEM)viathecableentryholein

the base, then connect the lead onto JP2 on the

DC58/58M (marked TO CONTROL PANEL).

5. Set the "HI/LO SECURITY" link to the appropriate

setting.

6. Secure the DC58/58M base to the control panel

base using the self-adhesive pads.

7. Refer to "Telephone Line Connections".

Stand-alone Installation (DC58 Only)

1. Isolate ALL power from the control panel (battery

and mains).

2. Do not attempt to continue if the mains or battery

supply is still present.

3. Remove the cover from the DC58 case and if

appropriate fit a pre-programmed NVM.

4. Connect the input channels to the appropriate

outputs on the control panel feeding all cables

through the cable entry hole in the base.

5. Ensure that "JP5" is set for the appropriate polarity.

6. Connect 12V and 0V to the control panel digicom

supply, if a line fault output is required use output 1

or 2 and program the output as line fault.

7. Set the "HI/LO SECURITY" link to the appropriate

setting.

8. Secure the DC58 base to the control panel base

using the self-adhesive pads.

9. Refer to "Telephone Line Connections".

Telephone Line Connections

1. Connection to the telephone network must be

made via an NTE5 master socket (Line Box).

2. Using the cable type 1/0.5mm CW1308, strip back

5mm of the required cores and feed through the

DC58/58M cable entry, see Figure 4.

☞Keep all telephone cables at least 5mm

away from other alarm cables.

3. CW1308 cable is available from RS Components

(PartNo.368-413).Alarmoranyothertypeofcable

must not be used.

4. Connect the three cores to the terminal blocks

marked A, B and BC.

5. Remove the two screws from the BT master jack

socket and remove the bottom section from the

master jack.

6. Connect the cable from A, B and BC terminals on

the DC58/58M to the BT master jack terminals, see

Figure 4 .

496545 Issue A 3of8 DC58 & DC58M

DC58 & DC58M

A1B1 B

BC Cable Entry

Telephone cable

Type 1/0.5mm CW1308

Telephone line to

"series connected"

telephone, Fax etc.

A = 5 - White/Blue ring

B = 2 - Blue/White ring

BC= 3 - Orange/White ring

Figure 4. Telephone Line Connections

7. A special insertion tool will be required to connect

the cable to the master jack, this is available from

RS Components (Part No. 470-487).

8. Replace the bottom section of the master jack

socket and do up the two screws. Refer to "Testing"

(see below).

NETLCD Remote Keypad Connections

To convert a standard NETLCD/TS900 remote keypad

intoaDC58/58Mprogrammerthefollowingisrequired:

NETLCD 32 character LCD remote keypad.

NETEKI Networker Engineer's Keypad

Interface lead.

Testing

Once all the installation steps have been completed,

proceed as follows:

1. Ensurethat you have informedthe ARC that youwill

be sending test calls.

2. When used in the stand-alone mode, ensure that

any unused reporting channels are linked to their

healthy condition or programmed not to report,

e.g.,ifchannel4 is programmedtoreportbutisnot

connectedtothecontrol panel, then link itto+12V

ifthe triggeris set to -ve or to 0V if the trigger is set to

+ve.

3. Connect power to the control panel. If the DC58 is

being used as a stand-alone, wait for

approximately 10 seconds for the unit to

automatically configure itself.

(a) If the NVM is un-programmed or fitted

incorrectly the red LED will flash rapidly.

(b) If the DC58/58M is to be programmed using

the NETLCD/TS900 remote keypad, plug it onto

the connector labelled "TS900 REMOTE". Refer

to "Programming" for further details.

channelis active the red LEDwill illuminate and

the dialling sequence will commence.

4. Send a test call by momentarily shorting the "TEST

CALL" pins together, see Figures 2 & 3 . This will

initiate a test transmission to the ARC.

☞The DC58/58M will not send a test call if

there is a parallel hand-set off hook.

5. Trigger all the relevant channels by:

(a) Setting and unsetting the control panel to send

open/close signals.

(b) Set the system and cause a full alarm to send

an intruder signal.

(d) Activateanyotherdevicesthatrequiretesting.

6. UnplugtheNETLCD remote keypadand secure the

cover of the DC58/58M using the two screws

supplied.

7. Finallyreplaceandsecurethecover on the control

panel.

DC58 & DC58M 4of8 496545 Issue A

DC58 & DC58M

Set I/D to "ENG"

NETEKI Lead

Pol.

TSNETLCD/TS900 Remote Keypa

Blue

White

Yellow

Black

Red AB

REMOTE

I/D

ENG

CDE

O/P-

Figure 5. Engineer’s Keypad Connections

Programming

Programming Menu

DC58 & DC58M

496545 Issue A 5of8 DC58 & DC58M

TELEPHONE NO.1

018112345678

TELEPHONE NO.2

018112345687

REPORTS TO NO.1

**34***8

Press any key

=Clearnumber

= Pulse Dial (P) or Pause (-)

=ToneDial(T)

DC58 Version 2.2

Press Any Key

Enter Telephone No. 2

ACCOUNT NO.1

0001

TELEPHONE NO.3

018112345679

Enter Telephone No.3

Enter account No.1

ACCOUNT NO.2

0001

ACCOUNT NO.3

0001

Enter account No. 2

Enter account No. 3

Select channels that report

to tel No.1 by pressing [1] - [8]

REPORTS TO NO.2

*234***8

REPORTS TO NO.3

*234***8

Select channels that report

to tel No.2 by pressing [1] - [8]

Select channels that report

to tel No.3 by pressing [1] - [8]

SET/DAY CHANNELS

***4****

Select Set/Day (Open/Close)

channels by pressing [1] - [8]

RESTORE CHANNELS

**34****

Select Restore channels

by pressing [1] - [8]

= Consecutive

= Alternative

=All

=WillNOTReport

=LimitedReport

= Full Report

Dialling Mode

is Consecutive

Extended Format

Will NOT Report

Select dialling mode:

Select point ID reporting mode:

TEST CALL PERIOD

Disabled

T.O.S Calls are

Disabled

Select test call period:

Select Temporary Out of

Service monitoring period:

= Disabled

=Daily

= Weekly

= Fortnightly

= Disabled

=Daily

= Weekly

= Fortnightly

Digi Output 1 is

Line Fault

INVERT CHANNELS

********

Select Invert channels

by pressing [1] - [8]

Select output type:

= Line Fault

= Digi Successful

= Digi Failed

=DigiActive

= Serial Coms Fault

Digi Output 2 is

Line Fault

Select output type:

= Line Fault

= Digi Successful

= Digi Failed

=DigiActive

= Serial Coms Fault

Ring Count is

Instant

= Instant

= Delayed

Select Ring Count

(DC58M Only):

= Disable

=Enable

3-WAY CALLING

Enabled

Enable/Disable 3-way calling

Enter Telephone No.1

Point ID Extended Format

Whenthe DC58/58Mis usedin the"plug-on mode" (i.e.

connected to a Menvier Security control panel) it is

possible to send additional alarm information to the

ARC, this can include circuit and user ID.

☞This feature is only supported by relevant

Menvier Security control panels, for details on

which control panels support this feature

contact Menvier Security Technical Support.

Point ID can be set to one of the following reporting

options:

1 Will NOT Report

This disables "Point ID Extended Format" and the

DC58/58M will only report "Fast Format" data to the

alarm receiver.

2 Limited Report

When "Limited Report" is selected the DC58/58M

willonlyreporttheextendedformatdatarelating to

the channel that is triggered. For example, if the

DC58/58M is programmed to report channels 2

and 3 (PA and Intruder) then the unit will only report

events relating to PA and Intruder activations.

3 Full Report

When "Full Report" is selected the DC58/58M will

report all extended format data to the alarm

receiver irrespective of the channels that are

programmed to report. That is, if all eight channels

are programmed as non reporting, the unit will still

report all events to the ARC.

Temporary Out of Service

This feature is used to test the integrity of the telephone

line by dialling all but the last digit of the first telephone

number. If the unobtainable tone is NOT detected it is

assumed that the line is in good working order,

however, if an unobtainable tone is detected the

DC58/58M will signal a line fault condition.

Ring Count (DC58M Only)

The DC58M Ring Count can be programmed for one

of the following options:

1 Instant

The DC58M will answer any incoming calls

immediately.

2 Delayed

The DC58M will answer any incoming calls after

approximately 30 seconds.

☞Some Menvier Security control panels allow

the ring count to be performed by the

control panel. If the control panel has a ring

count option then set the DC58M to "Instant"

and program the panel ring count to the

required amount.

DC58 & DC58M 6of8 496545 Issue A

DC58 & DC58M

Monitor Mode

Introduction

When the NETLCD remote keypad is left plugged on to

the DC58/58M it will act as a monitor, so that during

testing to the ARC the display will show the

communicator's status.

Transmitted Data Specification

The data transmitted to the alarm receiver is industry

standard fast format. The data contains the following

information:

Account No This is a 4 digit number and is

unique to the installation site.

Channel 1-8 Each channel can report its own

status code:

Code 1 = New Alarm

Code 2 = System Opened

Code 3 = Channel Restored

Code 4 = System Closed

Code 5 = Healthy Channel

Code 6 = Previously reported

event

Channel 9 This channel is normally referred to

asthestatus channelandisusedto

report the following:

Code 7 = Normal

Code 8 = Low Battery

Code 9 = Test

Typical Test Call

When the "TEST CALL" pins are momentarily shorted the

DC58/58M will send a test call to all programmed

telephone numbers. The display should show:

Other Monitor Messages

The following monitor messages may also be

displayed:

496545 Issue A 7of8 DC58 & DC58M

DC58 & DC58M

DC58(M) MONITOR

Waiting for I.D

DC58(M) MONITOR

Sending Data

Dialling the first telephone No.

Waiting for the alarm receiver to

answer the call and send its

identification tone (I.D.).

The alarm receiver is on line

and the DC58 is sending its data.

The data sent is displayed.

This is repeated for all

programmed telephone

numbers

The data was accepted and the

alarm receiver has sent its

acknowledgment tone.

DC58(M) MONITOR

Dialling Number 1

DC58(M) MONITOR

0001 5555 5555 9

DC58(M) MONITOR

Call Successful

DC58(M) MONITOR

Unobtainable

DC58(M) MONITOR

No Ack. Tone

DC58(M) MONITOR

Engaged

DC58(M) MONITOR

T.O.S Call Ok

No dial tone detected when the

DC58 went on line.

The number was dialled but an

unobtainable tone was detected.

The alarm receiver is engaged.

The number was dialled but a

"Special Information Tone"

was detected.

No reply from the alarm receiver.

The "Temporary Out of Service" test

call was successful.

The DC58 sent its data to the

alarm receiver, but the receiver

failed to give an acknowledgement

tone (corrupted data).

DC58(M) MONITOR

No Dial Tone

DC58(M) MONITOR

S.I.T. Tone Found

DC58(M) MONITOR

No Answer

DC58 & DC58M 8of8 496545 Issue A

DC58 & DC58M

This page intentionally left blank

Ce manuel convient aux modèles suivants

Table des matières

Manuels Téléphone portable populaires d'autres marques

Zte

Zte BLADE A520 Manuel utilisateur

Nokia

Nokia Lumia 620 Manuel utilisateur

Blackbe;rry

Blackbe;rry KEYone Manuel utilisateur

Bea-fon

Bea-fon X5 Premium Manuel utilisateur

Blackbe;rry

Blackbe;rry 8707 Series Manuel utilisateur

Blackbe;rry

Blackbe;rry Storm Mode d'emploi

LG LM-X420QN Manuel utilisateur

LifeWatch

LifeWatch V Manuel utilisateur

Bea-fon

Bea-fon SILVER LINE SL860 Manuel utilisateur

IKI Mobile

IKI Mobile KF4.5i Manuel utilisateur

Hitech

Hitech HT-850 Manuel utilisateur

Yezz

Yezz Fashion F10 Manuel utilisateur

Point Mobile

Point Mobile PM60 Manuel utilisateur

Blackbe;rry

Blackbe;rry Q10 Manuel utilisateur

Blackbe;rry

Blackbe;rry Bold 9900 Manuel utilisateur

Blackbe;rry

Blackbe;rry STORM 9500 - VERSION 5.0 Manuel utilisateur

LG LM-K420EMW Manuel utilisateur

ISAFE MOBILE

ISAFE MOBILE IS655.2 Manuel utilisateur