6
®The equipment is an item storage equipment, which cannot be used for routine production operations. It is
strictly forbidden to put too many items which are relatively hot into the equipment at one time, otherwise
the compressor will run for a long time, and be burned due to high temperature. Items must be put in
batches, so as to ensure that the Refrigerator is cooled step by step until the temperature required for
storing items is reached.
®Do not change the set temperature frequently in a short time, otherwise the expected setting effect may not
be achieved due to the large temperature inertia; Ensure that there is a certain air circulation space around
the cabinet when putting in items, especially do not block the temperature sensor in the cabinet (for
collecting the temperature of the cabinet), otherwise it will affect the stability and accurate control of the
temperature in the cabinet!
®Electrical appliances without production license shall not be used inside the equipment.
®Due to the refrigeration inertia, there is a certain difference between the actual display temperature and the
set temperature of the equipment, which is a normal phenomenon.
®Items shall not be placed directly at the bottom of the Refrigerator, but on the bottom shelf, otherwise the
refrigeration effect of the equipment will be affected.
®A special person shall be responsible for checking and recording the running status of the equipment every
day (record and check once every 2-4 hours). In case of failure or shutdown, the temperature in the
Refrigerator will rise. If it cannot be repaired in a short time, please take out the stored items and transfer
them to a place that meets the temperature requirements for storage to avoid damage to the items.
®When putting in items, if the moisture content of the items is too much or too little, it will affect the humidity
change in the cabinet, so it is best to keep the items sealed; The humidity of the working environment will
affect the change of humidity in the cabinet, especially if the door is opened too frequently and the door is
not closed properly.
®Before putting items into the equipment, it shall be confirmed in advance whether the temperature range of
the equipment meets the temperature requirement of the items, so as to avoid damage to stored items due
to the difference between the settable temperature of the equipment and the required temperature of the
items. Please pay attention not to block the air outlet and air inlet when putting items into the equipment.
Notes:
Warning:
4.5 Operation after Power Failure
3. We guarantee the normal operation of this equipment under certain conditions, but we are not responsible for any loss or
damage of stored items after power failure.
1. The equipment has a memory function for the set value. When the power is restored after power failure, the equipment
will continue to operate before power failure.
2. Once the equipment is powered off, it requires 5 minutes before it can be switched on again, so as to avoid damaging the
compressor.
®Keep all ventilation openings in the enclosure or, in the structure for building in, clear of obstruction.
®Do not damage the refrigerant circuit.
®Protection impairment if used in a manner not specified by the manufacturer.
®Protection impairment if used in a manner not specified by the manufacturer.
®The instructions concerning persons (including children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge and children playing with the appliance are not required.
®To avoid the risk of electric shock, this equipment must only be connected to a supply mains with protective
earth.
®Do not use mechanical devices or other means to accelerate the defrosting process, other than those
recommended by the manufacturer.
®Children are not allowed to play with this equipment as a game prop, otherwise the injury or loss caused
therefrom will be at their own risk.
®Do not modify this equipment without authorization of the manufacturer.
®No modification of this equipment is allowed.
5
6.Install the fixing plates(Apply to YC-725L、YC-725EL(110V 60Hz)).
2.Inventory of accessories: Please check the accessories and materials according to the packing list.
1.Remove the outer packaging of all products (including the protective foam in the packaging box).
4.Before use, remove the small wire shelf and put it at the bottom of the cabinet (applicable to YC-55L/YC-
55EL /YC-56L/YC-56ELand YC-75L/YC-75EL/YC-76L/YC-76EL).
YC-1505L).
Firstly, open the door handle as shown in the following figure;
Then, remove the screw for installing the door handle on the cabinet, and install the handle seat with this screw;
Finally, install the handle cover, insert both ends of the handle cover into the corresponding grooves of
the handle seat, and then press it to close it.
a.Firstly take out the two fixing plates and check if consistent.
Warning: Don't put the plastic bags within the reach of children, so as to prevent suffocation
accidents.
b.Remove the bolts from the fixing plate,and then fix the plate on the back of the refrigerator.
In order to install handles, the handles shall be placed together with accessories.
3. Cleaning: Clean the product once before use.
5. Installation of door handles (YC-650L,YC-725L, YC-725EL, YC-1015L,YC-1015EL,YC-1320L,
Handle installation method:
c.Connect the fixing plate to the immovable wall or bracket on the back of the refrigerator and finally
check whether it is fixed.
4.3 Preparation before use
4.4 First Power-on
Door handle
Mounting hole
Screw
Mounting hole
Screw
Fixing plate
2. Under no-load condition, connect the power cord to a special outlet with appropriate specifications.
3. After powering on, turn on the power switch of the equipment.Toggle the on/off battery switch to the ON position
located in the back of the unit.
5. Please store items in batches, with the items not exceeding 1/3 of the cabinet volume each time. Ensure that the
equipment is running properly after shutdown for more than 12 hours before putting in the next batch of items).
When using the equipment for the first time, please follow these steps:
6. Try not to open the door during cooling, otherwise the temperature will rise.
4. Check whether the operating temperature of the equipment reaches the required value, observe the normal start
and stop of the equipment for more than 24 hours, and put a small amount of items in the Refrigerator after
confirming the normal performance.
1. After the equipment is placed, leveled and cleaned, it shall stand for more than 24 hours, and then power it on to
ensure the normal operation of the equipment.
