MELICONI SPEEDY 110 Manuel utilisateur

Thank you for choosing Meliconi.

This simplified universal remote control contains all the main functions of most

TV remote controls. Insert the batteries and program your remote control before using it.

Keep your Instructions Booklet for future reference.

USING THE KEYS AND FUNCTIONS

FITTING THE BATTERIES

SET-UP

Read these instructions carefully before programming your remote control!

To use the remote control with your appliances, you must first program Speedy 110 as described below.

You can also visit our Internet site www.meliconi.com to have access to interactive instructions for easier

and faster remote control programming

•

Batteries must be changed once a year.

•

Change the batteries if the light indicator starts to flash during use. The batteries are low.

•

When removing batteries, insert the new ones within 5 minutes or you may have to

reprogram your remote control.

•

Make a note of the code for your TV on the adhesive label supplied inside the battery

compartment cover. This note will be handy if you have to reprogram your remote

control.

The remote control requires 2 new AAA/LR03 alkaline batteries. Insert the batteries as shown:

ON/OFF to turn OFF your TV and, in

some cases, to turn ON your TV.

Control the volume using

To select an external terminal.

To select the next programme or to turn

ON your TV.

Mute key.

Press them together to turn ON your

TV on programme 1.

To select the previous programme

or to turn ON your TV.

Control the volume using

Light indicator.

Istr SPEEDY 110+ guscio V4.qxd 12-12-2007 17:09 Pagina 4

When you have programmed Speedy 110 Meliconi, note down the code on the label in the battery

compartment cover.

To find the code for your remote control:

1. Hold down the and keys simultaneously until the light indicator at the top starts to flash

indicating that the remote control is searching for the code.

2. Release the keys and, within 12 seconds, press and simultaneously.

3. Release and and pay attention to the flashing of the LED: a long flash corresponds to a +while

a short flash corresponds to a -. Note the sequence of the 9 flashes and note them down on the label

in the battery compartment cover, from left to right.

PROGRAMMING YOUR REMOTE CONTROL

1. Make sure that the TV is ON.

2.Hold down the and keys simultaneously until the light indicator at the top starts to flash indicating

that the remote control is in programming mode.

3. Press key four times then point the remote control at the appliance. Press and release the key

slowly several times. STOP when your TV goes OFF.

4.When your TV is OFF, press the and keys simultaneously. When you release the keys, three

flashes indicate that the search operation has been completed correctly.

Additional check

Check that all 7 keys are operating correctly. If the commands work incorrectly or erratically, you have

probably entered a code for a similar but different remote control.

In this case, repeat the search procedure from point 2 until all keys respond correctly to the commands sent.

IF YOU DO NOT HAVE THE PROGRAMME SELECTION KEYS ON YOUR ORIGINAL REMOTE CONTROL

If your remote control does not have the programme selection keys (e.g. / , +/-, CH+/-..etc) once you

have programmed Speedy 110, you can still select the programmes from 0 to 9, as follows:

•Hold down the and keys simultaneously until the light indicator starts to flash indicating that

the remote control is in programming mode.

•Release the keys and press 9 times within 12 seconds. Three flashes indicate that

the operation has been completed correctly.

•Make sure you can change programmes from 0 to 9 using the and keys. If not, repeat the search

operation, starting from point 2.

Identify and take note of the TV code which you have searched for, following the code noting

procedure (see "PROGRAMMED CODE NOTING" section).

NOTE: DURING THE SEARCH OPERATION, THE LIGHT INDICATOR FLASHES MORE QUICKLY.

THE LIGHT INDICATOR STOPS FLASHING AND YOUR REMOTE CONTROL LEAVES

PROGRAMMING MODE IN THE FOLLOWING CASES:

•if no keys are pressed for 12 seconds

•if you press keys other than those indicated

•if the code search list is completed. In this case, visit www.meliconi.com or contact the call center.

PROGRAMMED CODE NOTING

Istr SPEEDY 110+ guscio V4.qxd 12-12-2007 17:09 Pagina 5

Once you have programmed Speedy 110, you can turn ON your TV in three ways:

•Press or .

•Press .

•Press and simultaneously: this sends the code for programme 1.

If the remote control is no longer programmed because it has been left without batteries for a long time

or has flat batteries, you can re-program it quickly as follows:

1. Hold down the and keys simultaneously until the light indicator at the top starts to flash

indicating that the remote control is programming.

2. Release the keys and, within 12 seconds, using the and keys, enter the nine-sign code which

you noted down before. At the end, three flashes indicate that the code has been saved correctly.

If not, try the code entry procedure again from point 1.

USING YOUR REMOTE CONTROL

To return to programme 1 directly, press and simultaneously.

RE-PROGRAMMING YOUR REMOTE CONTROL BY ENTERING THE CODE NOTED DOWN

WARRANTY: 2 years

The warranty ceases to be valid if the product is tampered with or

used incorrectly.

Remote control model Speedy 110

Purchase date

PROBLEM

The TV does not respond and the light

indicator does not light up when you

press a key.

The TV or VCR does not respond but the

light indicator does light up.

The TV does not respond and the light

indicator flashes.

Not all remote control commands are

working correcting.

The and keys do not select the

programmes.

TROUBLESHOOTING

SOLUTION

Check that the batteries are fitted correctly. If necessary,

replace them with 2 new 1.5 V AAA/LR03 alkaline

batteries.

Check that the batteries are new and that the remote

control is pointing at the appliance without any obstacles

in the way. If required, reset the remote control code by

repeating the programming procedure.

Batteries are low. Replace them.

You may have used the wrong code. Reset the remote

control code, following the programming procedure.

The original remote control may not have had this

function. In this case, set the code (press 9 times) as

described in the PROGRAMMING YOUR REMOTE

CONTROL section above.

If you have any queries about Speedy 110:

•read this booklet carefully – this will help you to solve almost all problems

•consult our Internet site www.meliconi.com to answer all your queries easily and quickly.

INFO-LINE

Agent's stamp

Istr SPEEDY 110+ guscio V4.qxd 12-12-2007 17:09 Pagina 6

Table des matières

Autres manuels MELICONI Télécommande

MELICONI

MELICONI Personal 3 plus Manuel d'installation et d'exploitation

MELICONI

MELICONI TLC02 Manuel utilisateur

MELICONI

MELICONI GUMBODY FACILE SMART Manuel utilisateur

MELICONI

MELICONI GumBody Personal 1 Manuel utilisateur

MELICONI

MELICONI Speedy 210 combo Guide d'installation

MELICONI

MELICONI Speedy 210 combo Manuel utilisateur

MELICONI

MELICONI GUMBODY FACILE 100 Manuel utilisateur

MELICONI

MELICONI Pratico 2 Manuel utilisateur

MELICONI

MELICONI Speedy 2.1 BIG Manuel utilisateur

MELICONI

MELICONI TLC04 Manuel utilisateur

MELICONI

MELICONI Personal 4+ Manuel utilisateur

MELICONI

MELICONI GUMBODY UNIVERSAL 6 LIGHT Manuel utilisateur

MELICONI

MELICONI personal 4 Manuel utilisateur

MELICONI

MELICONI Algo 2.1 Manuel utilisateur

MELICONI

MELICONI Control 5 500 PLUS Manuel utilisateur

MELICONI

MELICONI GUMBODY UNIVERSAL 5 SMART Manuel utilisateur

MELICONI

MELICONI LOGIC12 Manuel utilisateur

MELICONI

MELICONI SENIOR 2 RC Manuel utilisateur

MELICONI

MELICONI GumBody DIGITAL 2 SMART Manuel utilisateur

MELICONI

MELICONI Speedy 100 plus Manuel utilisateur

MELICONI

MELICONI PRATICO 2 Light Manuel utilisateur

MELICONI

MELICONI SPEEDY 210 STB Manuel utilisateur

MELICONI

MELICONI CONTROL 2 Simple Manuel utilisateur

MELICONI

MELICONI CONTROL TV 100 Manuel utilisateur

Manuels Télécommande populaires d'autres marques

Panasonic

Panasonic EUR7622KB0 Manuel utilisateur

Bang & Olufsen

Bang & Olufsen Beo4 Manuel utilisateur

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Manuel utilisateur

Multiplex

Multiplex PROFI TX 9 Manuel utilisateur

One Remote

One Remote RMB4 Manuel utilisateur

FUTABA

FUTABA 9ZAP - PART2 Manuel utilisateur

HR Matic

HR Matic HR MULTI 3 Manuel utilisateur

Yamaha

Yamaha ACC-GNRST-30-20 Manuel utilisateur

EisSound

EisSound KBSOUND Manuel utilisateur

Marantz

Marantz RC101 Manuel utilisateur

Conrad

Conrad FS20 TC6 Manuel utilisateur

Anritsu

Anritsu MP1777A Manuel utilisateur

Niles

Niles WVC100 Guide de dépannage

RCA

RCA RCU1300 Manuel utilisateur

Bang & Olufsen

Bang & Olufsen BEO6 Manuel utilisateur

GE 94901 Manuel utilisateur

Onbon

Onbon YQ1-75 Manuel utilisateur

FUTABA

FUTABA R7108SB Instructions d'installation