MegaLite N-E Color Wash Manuel utilisateur

USER MANUAL

Table of Contents

Safety Information……………………………………………………………………………………………. 3

Specifications…………………………………………………………………………………………………….. 4

Main Power Connection………………………………………………………………………………….. 5

DMX-512 Connection…………………………………………………………………...……………...... 5

Ri in the Fixture…………………………………………………………………………………………….9

DMX Profile......................................................................................................................... 6

Main Control Menu.......................................................................................................... 7

Cleanin & Maintenance................................................................................................9

Parts List.............................................................................................................................. 9

N-E Color

Wash

Check that the unit has not been dama ed durin transport

Protection A ainst Fire

1. Maintain a minimum of 1 foot distance from any type of flame.

3. Replace fuse only with the specified type and ratin .

4. Do Not install the unit to close to a heat source.

5. Make sure cable are properly secured away from unit movement.

6. Maximum surface operatin temperature 50ºc.

Protection A ainst Fire

1. Disconnect power before servicin .

2. For connection to main power supply proceed to pa e 5.

3. This unit must be earthed. (electronically rounded)

4. Do not expose unit to rain or moisture.

Protection A ainst Mechanical Hazards

1. Use safety chain when han in unit.

2. Use quality clamps or bolts when positionin unit

3. Do not open unit while it is on, risk of electrical shock.

Technical Information

Part Numbers

Fixture

4040– N-E Color Wash

Mechanical Specifications

Fixture

FixtureFixture

Fixture

Packaged for Shipping

Packaged for ShippingPackaged for Shipping

Packaged for Shipping

Size: 16.75”L x 5”W x 8.5”H

Weight: 6 lbs

Size: 18.75”L x 8.5”W x 7”H

Weight: 10 lbs

DMX Connectors: 3-pin XLR connectors

Power Connection: IEC

Thermal: Maximum ambient temperature 40°C

Maximum surface temperature 60°C

Fastening System: Mounting Yoke

Electrical Specifications

LED Quantity: 216

Red: 72

Green: 72

Blue: 72

LED Lifetime: 60,000 to 100,000 hours

LED Angle: 35°( ±5º)

Power Consumption: 100 - 240V 50/60 Hz

Ballast: Electronic

Watts: 16.1

Amps: 0.24

16.75 ”

3.5 ”

Protocol: DMX 512

DMX Channels: 4 Channels

Control options: Audio-trigger

Operating mode: Master/Slave, Stand alone

Control & Pro rammin

5 ”

8.5 ” 6.5 ”

8.25 ”

Main Power Connection

Caution!

1. Do not connect fixture to a dimmer system.

2. This unit has Auto switchin power supply. It will respond to 110V or 220V automatically

3. This unit must be earthed. (electronically rounded)

4. Replace fuse only with the specified type and ratin .

The occupation of the connection-cable is as follows:

DM -512 Connection

110V Connection

The fixture is equipped with 3 pin XLR Sockets for DMX input and output. The sockets are wired in parallel. Only use a shielded

twisted pair cable desi ned for RS-485 and 3 pin XLR plu s and connectors in order to connect the controller with the fixture or

the fixture with another.

DM —input DM —output

1. Shield

2. Si nal (-)

3. Si nal (+)

Caution!

At the last fixture the DMX si nal needs to be terminated with a terminator. Solder a 120

Ohm resistor between the (-) and the (+) si nal into a 3 pin XLR plu and plu it in to the

last fixture on the si nal run. Pre-manufactured terminator plu s are available for

purchase from your Me a-Lite dealer (HOS-DMXT).

Cable (USA) Cable (EU) Pin Connection

Black Brown

White

Green

Li ht Blue

Yellow/Green

Live

Neutral

Ground

220V Connection

Cable (USA) Cable (EU) Pin Connection

Black Brown

White

Green

Li ht Blue

Yellow/Green

Live

Ground

Rigging the fixture

Caution!

1. The installations must be carried out by an authorized dealer or trained professional.

2. Unit may cause severe injures if you have doubts concernin the safety do not install.

3. Unit is to be 24inches away from flammable materials (decoration material)

4. Use hi h quality installation equipment to han unit.

When ri in a unit it is very important that you follow common safety procedures. Ri in requires extensive experience includ-

in but not limited to calculatin workin loads, material bein used and periodic safety inspections. If you lack these qualifica-

tions, do not attempt the installation yourself, instead use a professional structural ri er.

When ri in the unit always be secured with a secondary safety attachment. The installation location of the projector has ot to

be built in the way that it can hold 10 times the wei ht for 1 hour with out any harmin . Installation should be checked at least

one time a year by a skilled person.

DM Profile

N-E Color Wash

DMX Chanel Function Description Value

Dimmer 0-127

1 Dimmer Strobe (slow to fast) 128-250

Dimmer Full On 251-255

2 LED Color Red LED intensity 0-255

3 LED Color Green LED Intensity 0-255

4 LED Color Blue LED Intensity 0-255

Main Control Menu

The control board on the fixture base is your interface

to access and control all the functions on the unit. Its

dipswitch interface ives you a code view of the op-

tions. The followin will explain each function and its

options.

001

002

004

008

016

032

064

128

256

DMX

1 2 3 4 5 6 7 8 9 10

001

002

004

008

016

032

064

128

256

1 2 3 4 5 6 7 8 9 10

DM Addressing

Turn dipswitch 10 to the Down position. Each dipswitch from 1 to 9 holds

a numerical value located below the dipswitch. Add the numerical value to

et the desired fixture start address channel. The user must assi n a

start address on the fixture that indicates the first channel reserved in the

controller.

For example, if you wish the first unit to start on address channel 85 you

will need to turn on dipswitch 1,3,5 and 7 (1+4+16+64=85)

DMX

001

002

004

008

016

032

064

128

256

FUN

1 2 3 4 5 6 7 8 9 10

Functions

Turn dipswitch 10 to the UP position. This function will turn on the func-

tions that will allow the unit to run a prepro ram function. Additionally, this

unit may serve as a master unit where other units will copy it’s functions.

To create a master unit connect the XLR cable from the output to the in-

put on the next unit. And address the next unit as fixture 1.

INPUT OUTPUT

FUNCTION 1 2 3 4 5 6 7 8 9 10

RED ON

GREEN ON

BLUE ON

STROBE SLOW MID FAST FASTEST ON

COLOR FADE SLOW MID FAST FASTEST ON

COLOR SNAP SLOW MID FAST FASTEST ON

CHASE LIGHT SLOW MID FAST FASTEST ON

SOUND ACTIVATED RAINBOW ON

DM 1 2 4 8 16 32 64 128 256 ON

Cleaning and maintenance

Installation Maintenance: The operator has to make sure that the unit is operatin safely and has the installations and electron-

ics checked by an expert every 2 years.

The followin points have to be considered durin the inspection:

1) All screws used for installin the device or part of the device have to be ti htly connected and must not be corroded.

2) There must not be any deformations on the housin , fixation and installation spots (ceilin , suspension, trussin ).

3) The electronic power supply cables must not show any dama es, material fati ue (e. . porous cables) or sediments. Further

instructions dependin on the installation spot and usa e have to be adhered by a skilled installer and any safety problems

have to be removed.

Disconnect from mains before starting maintenance operation!

Caution Dan er to life!

We recommend a frequent cleanin of the device. Please use a moist, lint free cloth. Never use alcohol or solvents!

1) The plastic cover will require periodic cleanin on usa e and environment. Environment with fo ers will require more peri-

odic cleanin as fo fluid tends to build up residues, reducin the li ht output.

Note: There is no serviceable parts inside the device except for the LED’s. Maintenance and service operations are to be carried

out by authorized dealers.

Replacing the fuse: Only replace the fuse with the same type and ratin .

Replacing the power cable: If the power cable of this device becomes dama ed, it has to be replaced by authorized dealers only

In order to avoid hazards.

Should you have further questions , please contact your dealer.

Parts List

4040-mwb Mounts with bracket &bolts

4040- c Glass Cover

4040-mainc Main PCB card

4040-ps Power supply

4040-ledmod LED module

Me a-Lite

5718 Kenwick St

San Antonio, TX 78238

Ph 210-684-2600 Fax 210-855-6279

www.me a-lite.com / info@me a-lite.com

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels MegaLite Projecteur

MegaLite

MegaLite Baby Color Q70 Manuel utilisateur

MegaLite

MegaLite Outshine T100 Manuel utilisateur

MegaLite

MegaLite VAZT LED P100 Manuel utilisateur

MegaLite

MegaLite Drama FS-LED 700 Manuel utilisateur

MegaLite

MegaLite Pro Color Cannon Manuel utilisateur

MegaLite

MegaLite 4035 Baby Color Q70 Manuel utilisateur

MegaLite

MegaLite Target Q190 Manuel utilisateur

MegaLite

MegaLite Obra Flood N180 Manuel utilisateur

MegaLite

MegaLite 4070-N-E Color Punch Manuel utilisateur

MegaLite

MegaLite Drama W LED Manuel utilisateur

MegaLite

MegaLite UniColor Manuel utilisateur

MegaLite

MegaLite Indi PAR RW300 Manuel utilisateur

Manuels Projecteur populaires d'autres marques

VIZULO

VIZULO Micro Martin Guide de l'utilisateur

EuroLite

EuroLite LED IP FL-100 SMD Manuel utilisateur

Cooper Wheelock

Cooper Wheelock XB12 Manuel utilisateur

Allen + Roth

Allen + Roth 17624-000 Manuel utilisateur

ADJ

ADJ 4 STAGE PAK Manuel utilisateur

Cooper Lighting

Cooper Lighting EGL91SW233 Manuel utilisateur

Max

Max 37496 Manuel utilisateur

BEGA

BEGA 85 143 Manuel utilisateur

Beamz

Beamz 151.226 Manuel utilisateur

EuroLite

EuroLite LED IP FL-8 Manuel utilisateur

Ledj

Ledj PERFORMER 36 RGB Manuel utilisateur

Perel

Perel ELS3 Manuel utilisateur

Perel

Perel ELS3WD Manuel utilisateur

LumX

LumX LM 36130 Manuel utilisateur

Xtricity

Xtricity 4-80053 Manuel utilisateur

Stahl

Stahl 6521/4 Series Manuel utilisateur

Ecosense

Ecosense EcoSpec Manuel utilisateur

Ayrton

Ayrton minipanel FX Manuel utilisateur