Meech Hyperion 971IPS Manuel utilisateur
1
Hyperion 971IPS
Operating
Manual
Long-Range DC Bar
Products shown in this document may be covered by one or more patents, patents applied for
and/or registered designs and/or trade marks. For further information please refer to our Head
Ofce or visit www.meech.com.
© Meech Static Eliminators Ltd., 05.04.2013
Contents
Introduction 3
Unpacking and Inspection 4
Contents 4
Standard Equipment 4
Optional Equipment 4
Features of Hyperion 971IPS 5
Installation 11
Operation 15
Maintenance 15
Troubleshooting 17
Repairs and Warranty 17
Technical Characteristics 18
CE Approval 18
Health and Safety 19
3
Introduction
The Hyperion 971IPS is a powerful, pulsed DC ionising bar. It is used to control
static electric charges in mid to long-range applications (150-900mm). An integral
15kV pulsed DC power supply allows for easy installation on printing, converting and
packaging machinery. Requiring only a 24VDC supply, the 971IPS removes the need
to route high-voltage cabling through the machine.
In most installations the default settings of the bar will provide exceptional static
control. The local LED indicators show the operational status of the bar and advises
when the bar requires cleaning.
Demanding installations can take advantage of the adjustable output of the 971IPS.
Using the optional Hyperion BarMaster remote programmer, the frequency and
balance can be optimised to suit the application. Additionally, the lon Current alarm
setting can be changed to guarantee the required performance levels on critical
processes.
The Hyperion BarMaster remote programmer is available for purchase from the Meech
network: Visit www.meech.com to nd your nearest Meech ofce or distributor for
further product information.
4
Unpacking And Inspection
Your Hyperion 971IPS bar was carefully packed at the factory in a container
designed to protect it from accidental damage. Nevertheless, we recommend careful
examination of the carton and contents for any damage.
If damage is evident, do not destroy the carton or packing material and immediately
notify the carrier of a possible damage claim. Shipping claims must be made by the
consignee to the delivering carrier.
Contents:
Standard Equipment
971IPS Bar Mounting Kit
Optional Equipment
Power Cable - 4 Pin M8
(straight or 90º elbow)
Available in 2,3,5 and 10M
lengths.
24VDC Supply & IEC
cable
BarMaster remote
programmer.
Allows optimisation of the
output of the 971IPS
5
Features and Benets of Hyperion 971IPS
Low voltage wiring and Integrated Power Supply
The 971IPS is powered by 24VDC via a 4-pin M8 Connector.
Overall look
The prole of the Hyperion 971IPS bar is rounded, with minimal dirt traps, making it
useful for cleanroom applications. The bar has good rigidity, allowing it to span wide
widths. Mounting is by M4x20 T bolts in a slot at the rear of the bar.
6
Shockless Emitters
The Titanium emitter pins on the 971IPS are resistively coupled to the high voltage
supply. This avoids sparking and operator shocks.
Sealed Construction
IP64 or IP65 construction allows the bar to be mounted in areas subject to occasional
wash-down or spillage. If the bar does become wet it must be thoroughly dried before
being powered-up.
Emitter Assembly
The emitter assembly is a one piece moulding with a 1mm diameter sharp titanium
emitter pin. The use of titanium pins has a long history at Meech. Extremely hard
wearing, the pins last for many years. The emitter features castellation that protects the
operator from the point of the emitter. The castellation also allows very easy cleaning of
the pin using a brush. This is a great improvement on other pulsed DC bars. The open
design of the emitter also gives a performance boost over previous systems.
7
Meech Emitter Key and Replacement Emitters
Replacement emitters are available in bags of ten. Each bag includes an emitter key to
allow their easy removal and re-tting. tool to facilitate removal and replacement of the
emitter pins is also available.
Air-Boost
Air Outlets
Air Outlets
Whilst the long range performance of the Hyperion 971IPS is excellent, some
installations can require the use of air assistance to get full control of the static. This
can either be by increased speeds of decay and/or by increased ionisation range. Air
outlets either side of the emitter pin ensure that the integrated air-boost is extremely
efcient. Each 971IPS bar is supplied with a 6mm push-t air tting pre-installed.
8
Clean Pin Alert LED and Output
Red ashing LED shows that bar is dirty and needs cleaning. Solid red illumination
indicates a fault with the high voltage output.
No light - OK
Red ashing - Cleaning required
Red constant - Fault
The signal is an open collector output. Open circuit when the system is OK (Flashing
green LED). Grounded when the Clean Pin alert is active (Flashing red LED) or
System fault (Solid red LED).
The output signal is a constant signal irrespective of whether the LED is ashing red
or constantly red. In either case, the signal alerts the operator to inspect the bar to
discover what has caused the alert.
External
Alarm/Lamp/Relay
24
V Max
Output External
Alarm/Lamp/Relay
Output
20m
A Max
Output OFF
(= Green LED Flashing)
Output ON (=
Red
L
ED Flashing or Solid
)
Open Collector Alarm output
Table des matières
Autres manuels Meech Ioniseur d'air
Manuels Ioniseur d'air populaires d'autres marques
Static Clean
Static Clean 4203UC Manuel utilisateur
SCS
SCS 960 Manuel utilisateur
Desco EMIT
Desco EMIT C/E Series Manuel utilisateur
Best Living Systems
Best Living Systems KHAOS Manuel utilisateur
SCS
SCS 963E Manuel utilisateur
Desco EMIT
Desco EMIT Chargebuster 50680 Instructions d'installation et d'utilisation
Terra Universal
Terra Universal IonBar Guide d'installation
Phonocar
Phonocar 04971 Manuel utilisateur
Klarstein
Klarstein ST. OBERHOLZ OFFICE Manuel utilisateur
Life Ionizers
Life Ionizers Fuzion Manuel utilisateur
ITW
ITW Simco-Ion IQ Power Fantom Manuel utilisateur
LIFE Ionizer
LIFE Ionizer M7 X NG Manuel utilisateur