MCS Design ET Series Manuel de référence
1
The manual for the Installation, use and maintenance of the fireplace
CONTENTS
Fireplce Configuration：…………………………….3
Structural Decomposition：…………………………4
Product Key Description：………………………….5
Installation Notes：………………………………….6
Product Using：……………………………………..13
Voice Prompts Description：………………………14
Maintenance & Warranty：…………………………15
2
Thanks for choosing and using our intelligent 3D fireplaces with remote control .Please
read the instructions carefully when you are ready to use the product.And please kindly
operate the fireplace in accordance with the procedure so you can fully enjoy the services
provided by our company.
This manual Copyright owned by Changzhou Entu Electromechanical Technology
Co.,Ltd.Without written permission,any part of this manual can’t be
reproduced ,translated ,stored in database or retrieval system.And It can't be transmission in
any means such as electronic,copy, recording etc.
The Company reserves the right to any product improvement without prior notice.
The products, product color and type should be as standard as the real goods you
purchase.
This manual applies to the intelligent ethanol fireplace.
The instruction of this manual is as following:
This manual includes the fireplace installation, use and maintenance. It is very simple for
the fireplace ignition,use and maintenance procedures.So the users can operate it by
themselves.
Warranty and Installation Information:
If any of the following situations occur, we will be exempt from the obligation and won't bear
any responsibility :
1.Subsequent alteration fireplace structure and its associated components.
2.using the fireplace system components that is not our company approved and produced.
3.Not According to the requirements of the manual to install the fireplace.
3
For your safety:
Please don't store or use any flammable, gas or liquid in the fireplace or in 500mm range
around the fireplace.
To install officers: Please leave this manual when installing equipment.
To the user: Please keep this manual for future reference.
The configuration table
specification:
subject to the actual purchase
Model:
ETseries
Ignition method:
high energy ignition
high ignition energy:
key/remote control
fuel:
75%-95%A alcohol
oil consumption:
can be adjusted according to the
customer’s requirements
burn duration
can be adjusted according to the
customer’s requirements
noise(positive)
max10dB/min5dB
fuel tank capacity
subject to the actual purchase
Dimensions
subject to the actual purchase
4
basic configuration
>tilt automatic protection devices>high
energy ignition devices>child lock
device >panel temperature over-top
protection device>tank upper and lower
limit reminder protection>voice
prompt(Chinese and English
optional)on tank
optional
indoor carbon dioxide remind
protection device>indoor temperature
device
Meet a criterion
Meet a criterion
CE.CMA
Accessories
manual,remote control,power
adapter,warranty card,alcohol filled
tube(plus filter head),cleaning cloth
5
Structural decomposition
1. high-energy ignition head 2.alcohol outlets
3.high-level probe 4.alcohol discharge pipe
5.the discharge valve 6.alcohol filler one
7.the power switch 8. the low level probe
9.the start switch 10.the switch for filling alcohol
11.the alarm release switch 12.the probe signal is received
13.DC power input plug 14. alcohol filler two
6
Product Key Description
Host panel buttons
The start switch ( ignition automatically and adding the ethanol automatically after
starting)
Filling fuel switch ( add fuel automatically after start the button and stop
automatically after filling full）
Discard Alarm switch (this lamp will stay lit when the device fails )
Child lock switch (hold down the two keys and the child lock switch will start.
All the buttons will be limited)
Remote control panel buttons
The start switch (automatic alcohol ignition and automatic cycle work,after starting the
fireplace)
Filling Alcohol switch (automatically add alcohol after start and stop automatically
after filling full
7
Discard Alarm switch (this lamp will stay lit when the device fails .Press the button
and the alarm will be discarded)
Installation Notes
Installation requirements:
There should be no flammable materials near to the fireplace and the space upper the
fireplace left Should be 80-100CM.The fireplace can be decorated by nonflammable
decorations, such as stone,metal materials and refractories etc.But we can't use gypsum
board , wood and other combustible materials to decorate the wall side face , surface or top
face.Otherwise you can’t install and use.it。
The plane for installing the fireplace can be stone and stainless steel.The stone thickness
should not be less than 20MM and the thickness of the stainless steel is more than 2.5MM.
We should make the panel to be U-shape.Each segment distance should not be more
1meter and flat area can not exceed 0.5 square. Otherwise, there will be thermal
expansion,deformation and fall off etc.!
There should be ventilation holes, cracks and channels between the inside and outside of
8
the installing holes. There should be 0.16 square meter for ventilation every per 1meter of
the fireplace.So it is good for Ventilation and heat dispersion as well as assisted combustion
When multiple fireplaces are installed and used at the same time.It must be in a well
ventilation environment. So that it can ensure the indoor temperature is not very high. If the
indoor room is no needed to be warm, you need to reserve exhaust holes on upper of
fireplace.The size is according to the number of combinations of the fireplace and the
burning tank length reserved. The internal of ceiling on top of decoration needs adiabatic
iron sheet pipe that is wrapped with asbestos and ventilation with the outside world.And It
needs to install fans on the middle of the pipe or external wall .For three sets of1000MM
fireplaces,it needs to install one set 300W external motor fan. The control section may be
sensing thermostat or switch installed on the wall that is near the fireplace mounting desktop
to turn on fireplace simultaneously.
Before decoration,there should the pre-made holes aside, fireplaces power reserved and
wind power reserved etc. After installing the fireplace, heat protection must meet
requirements of heat removal , protection and fire prevention . If you don't comply with the
above installing requirements, please do not install and use. Otherwise incomplete
combustion will occur.And the flame will be not beautiful .If the decorations are flammable,
there will be a risk of a fire and indoor temperature will rise and so on.
When you use fireplace,you should install a fire extinguisher near the fireplace in the home
and teach user how to use the fireplace to prepare for contingencies.
Operating instructions:
Please install the fireplace in the appropriate level installation trough or on the smooth
9
surface level floor where there is no combustible all around 50CM range . The fireplace can
not be installed on an uneven surface table or floor.If the tilt is beyond 15 degrees,the
machine will start dumping protection device and the machine will alarm. And the machine
will not start.
PictureA picture B
Picture C
Power Connection:
As shown in picture A: The 12V power adapter that random distribution or AC power cord
into a grounded three wire 110V-240V power socket, the adapter output 12V socket plug
into the right end of the round socket on the machine (if it is the power line, insert the socket
holes in the side of the machine) the machine can be powered standby operation. The
indoor AC power lines need to have leakage circuit breaker protection device (please install
the fireplace control power switch near the fireplace installation counter tops ).
10
Alcohol filler（１）：
As shown in picture B: open fireplace panel door, you will see a plastic tube mouth (there is
a power switch inside the machine ) connected the random distribution hose into alcohol
bucket purchased back.When turn on the filling switch, it can automatically extract the
alcohol to the fireplace fuel tank (if it is the initial power-up,filling pump will automatically
start to fill .If the fuel tank does not reach a high level within 25 minutes, the machine will
alarm and stop working.) After all filled up, it will automatically stop filling.And then pull out
the hose by hand clenched roots.Please pay attention not to drip alcohol. Ignite and use
after wipe clean.
Alcohol filler（２）：
Picture C shows: on the right side of the machine, there is a white interface.When you
design external storage tank in the first design time, please connect random configure the
hose here and connect random distribution hose into external storage tank.When pressing
filling witch, you can automatically extract alcohol and fill into fuel tank (when use in the
initial power-up, filling pump will automatically start to fill. If the fuel tank does not reach a
high level within 25 minutes, the machine will alarm and stop working) until the tank is filled
fully with voice prompts then it will stop to add the fuel automatically .when the machine
starts to work,, if lack of fuel storage tank inside the machine, the machine will automatically
replenish combustion, such cycle, as long as the external storage fuel tank full. you can
always use the boot cycle.After this interface connected ,it can add alcohol without artificial
to the auxiliary for long . (Suggested use this interface function).
Special note:when choose filler moment (1) ,ensure that the fireplace in the off state and no
Table des matières
