McLelland PLA2DI Manuel utilisateur
PLA2DI
OWNERS MANUAL
POWER AMPLIFIER
240W
2
* Two Channels Model – 120W RMS/Per
Channel
* Slot card for Dante interface receiver
(DSC02).
* Stereo into 4-8 Ohm loads.
* Bridged mode 240W output for 70V or
100V (Direct Drive)
* Power down after ~15 minutes of no signal
and com ply with Energy Star Power
consumption limits of < 0.5W in standby.
* RED LED (Front Panel) to indicated Standby
mode is active.
* Terminal Block analog audio inputs.
* Selection for Power-Up mode.
* Switch for High Pass Filter.
* Natural cooling without Fan.
* TRIGGER could be external remoting
ON/OFF.
* Short circuit protection.
* Overheating protection.
* Optional accessory card slot for Dante
Receiver.
FEATURE
REAR PANEL FEATURES
1 7 8
4
25 3 6 9
Power On Selection
1. ON : The unit always Power ON, and will not go to Standby mode.
2. AUTO : The unit goes to Standby mode after 15 minutes of no signal sensing.
3. TRIGGER : The unit only power on by providing 12VDC at Trigger In(Rear Panel).
4. LED : GREEN indicates Power On. RED indicates Standby mode.
FRONT PANEL FEATURES
1 2 3 4
3
Frequency Response
Signal to Noise
Input Sensitivity
Gain Value
Input Impedance
Maximum Input Level
Trigger In/Out
TECHNICAL SPECIFICATIONS
Stereo Mode (all channels driven)
120W x 2, 8 Ω(31 V) RMS output (steady state), per channel @ < 1 % THD+N
120W x 2, 4 Ω(22 V) RMS output (steady state), per channel @ < 1 % THD+N
20 Hz - 20 kHz, +/- 2 dB @ 4ΩLoad
>90dB @ 1W(20 Hz - 20 kHz)
1.0V (+2.2dBu) @ Max Output 4Ω
25 dB @ 4Ω
>10k, Balanced.
12.3 V (+24 dBu)
DC 12V
Bridged Outputs For 70V/100V (Switch at “HIZ” position)
240W, 70V @ < 1 % THD+N 240W, 100V @ < 1 % THD+N
High Pass Filter
Input Connector
Trigger Connectors
Output Connectors
Dimensions
Net Weight
Power Requirements
80 Hz(±2dB)
5 pin Euro terminal
3.5 mm Jacks
4 pin Euro terminal (4Ω/8Ω) 2 pin Euro terminal (70V/100V)
214mm(W) x 249.8mm(D) x 44mm(H)
1.94 Kg
100 - 240 VAC, 50 - 60 Hz, 350W
1. INPUT: DSC02 Dante Interface receiver,
connecting with Dante network switch.
The network LED will illuminate yellow when
the unit is connected to the Dante network.
The network LED will illuminate green /
blink when the unit has an IP address and is
communicating to the Dante network.
Note: Dante receiver will need the power
from the switch with PoE function..
Note: In AUTO mode, when receiving the
signal from Dante network, the amplifier will
be triggered ON.
2. LEVEL : Adjust the level of output.
3. HPF: High Pass Filter (80Hz)
4. TRIGGER IN : Apply 12VDC to this
connector to active the unit.
5. TRIGGER OUT : Provide 12VDC to
trigger another device.
6. OUTPUT SELECT SWITCH :
4Ohm/8Ohm and HIZ for 70V/100V.
7. SPEAKER : Connect with 4 Ohm or
8 Ohm speakers.
8. 70V/100V: Connect with
Constant-Voltage speakers directly.
9. AC INPUT
4
DANTE AUDIO INTERFACE
2x2 audio channels
I2S digital audio format
16, 24 or 32-bit audio samples (per device or
per channel)
44.1 KHz, 48KHz, 88.2KHz and 96KHz sample
rates
Power supply: PoE, 52V 36 mA
DANTE CONTROLLER
PLA2Di is built in Dante interface and
compatible with the software “Dante
Controller”.
The software “Dante Controller” is free to
download from the company of Audinate
(the owner of Dante technology). To install
the software on the computer, please visit the
link:
https://www.audinate.com/products/software
/dante-controller
And the “User Guide” of “Dante Controller” is
available on the Audinate websit:
https://www.audinate.com/resources/technic
al-documentation
The tables below list the minimum system
specifications for the computer to use Dante
Controller :
Component Minimum Requirement
Processor GHz or better
Memory 512 Mbytes RAM
Network Standard Ethernet network
interface (100Mbps or Gigabit) or wireless
LAN (Wi-Fi) interface
Operating System
Windows 7 (SP1 and above), 8.1 and 10
NOTE: Both UTF-8 and Unicode are
supported EXCEPT for host or device names;
the DNS standard does not support Unicode
for these
Mac OS X 10.11.6, 10.12.6 and 10.13
NOTE: Intel architecture only; PPC
architecture is not supported
NETWORK INTERFACE
Standard 100Mbps Ethernet
RMII Ethernet interface with MDIO
Hardware time-stamping, supporting
sample-accurate playback
Transmit flows: 2 (unicast or multicast)
Receive flows: 2 (unicast or multicast)
Latency from 2ms
5
CONNECTION DIAGRAMCONNECTION DIAGRAM
Stereo mode (4 Ω / 8 Ω)
Bridged mode (HIZ 70V / 100V)
Set to HIZ
Determine 70V or 100V
Set to 4Ω/ 8 Ω
6
Table des matières
Autres manuels McLelland Amplificateur
McLelland
McLelland AVD-800P Manuel utilisateur
McLelland
McLelland HP1200 Manuel utilisateur
McLelland
McLelland Power Pro 300 Manuel utilisateur
McLelland
McLelland AMP-235 Manuel utilisateur
McLelland
McLelland MAP-1200EW Manuel utilisateur
McLelland
McLelland HPD-1500 Manuel utilisateur
McLelland
McLelland PLA2FX Manuel utilisateur
McLelland
McLelland AVD-800P Manuel utilisateur
McLelland
McLelland BP-1 Manuel utilisateur
McLelland
McLelland AMP-D25MC Manuel utilisateur
McLelland
McLelland MAP 1200HD Manuel utilisateur
McLelland
McLelland MAP1200WD Manuel utilisateur
McLelland
McLelland McLelland D20BR Manuel utilisateur
McLelland
McLelland CA1250 Manuel utilisateur
McLelland
McLelland PLA2 Manuel utilisateur
McLelland
McLelland MAP 1200 Manuel utilisateur
McLelland
McLelland PR-150 Manuel utilisateur
