MCDI Decrypta3 Manuel utilisateur

MCDI SECURITY PRODUCTS INC.

7055 JEAN-BOURDON MONTREAL QC H4K 1G7 Canada

PH: +514-481-1067 FAX: +514-481-1487 suppor[email protected]

TABLE OF CONTENT Page 1 | 41

Operating guide for Alarm Receiver D E C R Y PT A 3

MCDI Security Products Inc.. Internet: mcdi.com

7055 Jean-Bourdon Avenue, Montreal, QC, Canada H4K 1G7 Telephone: +514-481-1067 Fax: +514-481-1487

CONTENTS

Description................................................................................................................................................................................................2

What’s in the box ..................................................................................................................................................................................2

Physical description of DECRYPTA3........................................................................................................................................2

Size ....................................................................................................................................................................................................2

Buffer memory ...................................................................................................................................................................................2

Buzzer Alert/Warning.........................................................................................................................................................................2

Powering DECRYPTA3receiver ...................................................................................................................................................4

Configuring DECRYPTA3 receiver ............................................................................................................................................... 7

MCDI winExprecium2.exe ....................................................................................................................................................................7

MCDI Axe configurator 0.1.0 ................................................................................................................................................................7

Installation ..........................................................................................................................................................................................8

Un-Installation....................................................................................................................................................................................8

Usage................................................................................................................................................................................................. 8

Starting other MCDI software from Axe .......................................................................................................................................... 10

Logger tool .........................................................................................................................................................................................10

Parameter definitions ..........................................................................................................................................................................11

Transmission rate...................................................................................................................................................................................13

Transmission rate Serial port..............................................................................................................................................................13

Transmission rate USB port ...............................................................................................................................................................13

Connecting DECRYPTA3to PCs................................................................................................................................................13

Front panel commands and displays.....................................................................................................................................................16

Toolbox ...................................................................................................................................................................................................21

Configuration tools .............................................................................................................................................................................. 21

Communication tools ..........................................................................................................................................................................21

Software tool COMIRQ ....................................................................................................................................................................21

Software tool WINCOMM ................................................................................................................................................................22

DOS Not available............................................................................................................................................................................... 22

LINUX ..................................................................................................................................................................................................22

MACINTOSH.......................................................................................................................................................................................23

WINDOWS ..........................................................................................................................................................................................23

Receiving ................................................................................................................................................................................................ 27

Listen-in, Two way voice.....................................................................................................................................................................27

Transmission to computer and printer in MCDI mode....................................................................................................................... 28

Transmission to computer and printer in ADEMCO 685 / Surgard emulation mode........................................................................30

Messages from DECRYPTA3to DECRYPTA3printer port:.......................................................................................31

Warranty ................................................................................................................................................................................................. 31

Legal compliance and Warning .............................................................................................................................................................32

United States Regulation FCC Warning.........................................................................................................................................32

EC Declaration of Conformity .............................................................................................................................................................33

EN41003 Warning Application Note 48, Issue 5................................................................................................................................34

Glossary..................................................................................................................................................................................................35

Version 070710

DESCRIPTION Page 2 | 41

Operating guide for Alarm Receiver DECRYPTA3

MCDI Security Products Inc.. Internet: mcdi.com

7055 Jean-Bourdon Avenue, Montreal, QC, Canada H4K 1G7 Telephone: +514-481-1067 Fax: +514-481-1487

DESCRIPTION

Alarm Receiver DECRYPTA3

The twin line alarm receiver DECRYPTA3 for PC compatible computers is a MCDI product. This new breed of alarm

receivers is equiped with advanced features such as USB port and dual output to PC.

DECRYPTA3is available in RoHS and non RoHS version. Must be specified at the time of the order. Pricing differs

between the two versions.

What’s in the box

DECRYPTA3 Alarm Receiver

Cables:

2 RJ11 Phone cables

1 USB Type A to Type B cable 6 feet (1.8M)

1 Serial communication cable 6 feet DB9F to DB9F Null modem

1 Printer loopback plug

Power:

1 AC/DC power supply with localized IEC power cord.

1 Power cable for batteries (red and black)

Documentation/tools/drivers

1 Printed manual

1 CD with:

PDF documentation/tools/drivers/

Windows logger software

WinSAMM Central station trial version

Drivers and configuration tool WINEXPRECIUM2.EXE

Physical description of D E C R Y PT A 3

Size Receiver has all out dimensions ( with Acrylic cover ) :

9” (L) x 6.3” (W) x 3.1”(H) Stand Raised

229 mm (L) x 161 mm (W) x 79 mm (H)

9” (L) x 6.3” (W) x 2.25”(H) Stand Lowered

229 mm (L) x 161 mm (W) x 58 mm (H)

Receiver has all out dimensions ( outer cover removed for insertion in PC/Server ) :

8.95” (L) x 5.75” (W) x 1.66”(H)

222 mm (L) x 146 mm (W) x 42.3 mm (H)

Measurements do not include connectors

Housing: Inner Box : Anodized aluminium, green.

Outer Cover : Clear and black acrylic.

Front : Mylar and Polyester tactile membrane.

Back : Polyester membrane and aluminium.

Buffer memory Buffer holds up to 1800 events in Native mode (4+2 signal). Buffer is used when computer

is absent. Unit keeps printing during fail time if power is connected and maintained. When

computer comes back on, buffer empties to the computer. If more than 1800 events (4+2

Native mode ) are received in the buffer during fail time, DECRYPTA3 writes over the

oldest event. Written records may be available on printer connected to parallel printer port.

Alert/WarningBuzzer On board buzzer is available for alert warning when the Computer is absent.

Is enabled if setup parameter “Check printer” is set to Yes.

Is activated (starts buzzing) by event to be printed on DECRYPTA3 printer port.

DESCRIPTION Page 3 | 41

Operating guide for Alarm Receiver DECRYPTA3

MCDI Security Products Inc.. Internet: mcdi.com

7055 Jean-Bourdon Avenue, Montreal, QC, Canada H4K 1G7 Telephone: +514-481-1067 Fax: +514-481-1487

To stop buzzing press ON-LINE printer key twice (2). Refer to printer connected to DECRYPTA3

parallel printer port. Will resume buzzing if printer is left off-line.

DE CR Y P TA 3 – FRONT VIEW

DE CR Y P TA 3 – REAR VIEW

DESCRIPTION Page 4 | 41

Operating guide for Alarm Receiver DECRYPTA3

MCDI Security Products Inc.. Internet: mcdi.com

7055 Jean-Bourdon Avenue, Montreal, QC, Canada H4K 1G7 Telephone: +514-481-1067 Fax: +514-481-1487

REAR PANEL DESCRIPTION

USB PORT

Type B USB connector. USB client to host cable supplied

SERIAL NUMBER TAG

All DECRYPTA3 serial number contain 8 digits. Please

quote serial number in emails or when calling for support to

speed up identification process. Serial number appears in

configuration tool when using USB output.

SERIAL (DB9 male connector)

Data transfer to computer:,

Null modem cable supplied (DB9F to DB9F)

Serial port: 1200 Baud, 8 bit, 1 stop bit

Pin 2 = transmit

Pin 3= receive

Pin 7 = ground

RELAY TERMINAL 2 POSITIONS.

Terminal block used for trigger of external unit by inboard relay

( 30V DC 1A max). Supports normally open or normally closed.

GROUND POST

Used to mechanically ground the unit. Refer to Electrical feed

for more details.

POWER SUPPLY INPUT (SPU15A-104 )

100-240VAC to 9VDC 1.66A supplied with D3

BATTERY INPUT

12 VDC

Supplied battery connector red = + black = -

Refer to section Electrical feed before using.

PRINTER (DB25 female connector)

Printer parallel port. Raw signals received by D3.

LINE 1, LINE 2

Incoming phone lines

Tip

Ring

Powering DECRYPTA3 receiver

In this section

Electrical inputs

Notes on electrical installation for DECRYPTA3

Alternative power source 9-12V DC

USB Hub

Ground post

Using a battery charger

Warnings

ELECTRICAL INPUTS

DECRYPTA3 can be powered from:

1.Power Supply Input ( 9 VDC adaptor supplied )

and / or

2.Battery Input ( 12VDC ) using supplied cable

1. DE C R Y P T A 3 powered from the POWER SUPPLY INPUT

DECRYPTA3 can powered from the 9-12VDC only. Minimum requirements 9VDC 500 Ma. Severe damages to the

unit may occur if power supply delivers more than 14VDC.

Power led of front display will be ON steady when the DECRYPTA3gets the power from the Power Supply Input.

DECRYPTA3 is supplied with a 100-240V AC / 9 V DC power adapter. This power adapter is supplied with an IEC

power cord for localization.

DESCRIPTION Page 5 | 41

Operating guide for Alarm Receiver DECRYPTA3

MCDI Security Products Inc.. Internet: mcdi.com

7055 Jean-Bourdon Avenue, Montreal, QC, Canada H4K 1G7 Telephone: +514-481-1067 Fax: +514-481-1487

WARNINGS

-Removal of the power source during reception of an alarm signal may result in losing said signal.

-If 9-12VDC input is used as DECRYPTA3 sole source of power, events in receiver buffer will be not be lost when

power is removed and will be transmitted to PC when power is restored.

2. D E C R Y P T A 3 powered from the BATTERY INPUT

DECRYPTA3 can powered from a 12VDC battery only. Minimum requirements 12VDC 500 Ma. Severe damages to

the unit may occur if the battery delivers more than 14VDC.

Power led of front display will be blinking when the DECRYPTA3gets the power only from the Power Supply Input.

When both sources are used, the led will be ON steady.

WARNINGS:

-MCDI recommends choosing a high quality lead-acid battery or gel type. Most stores selling security equipment hold a variety of

power levels to choose from.

-If not charged, the battery will discharge. DECRYPTA3 does not provide battery supervision or charge to battery.

DECRYPTA3 is supplied with a Molex lock type connector. This connector has a red and black wire for connection to

battery.

-Do not use a battery supplying more than 14V DC. Significant heat dissipation will result and may damage unit. Do not use a

battery showing signs of tear, leak or corrosion.

-Never connect a faulty or drained battery to the DECRYPTA3.

Battery time

To calculated battery time:

HOURS OF CONTINUOUS BATTERY OPERATION = POWER IN A-H

Example with a fully charged new battery – 500mA drain from DECRYPTA3:

12V 600 mAh

1h12min

12V 700 mAh

1h25min

12V 70 Ah

140h

Always refer to battery manufacturer application notes on charging, using and discharging a battery.

Using 2 x 6Vbatteries (serial connection)

In using a serial connection, voltage of each power source will be added and delivered to DECRYPTA3.

Using 2 x 12V batteries (parallel connection)

Using a parallel connection of batteries, resulting current to DECRYPTA3 is the sum of current provided by each

source. Batteries should be matched to prevent heating among power components.

Battery charger

A battery along with a battery charger may be used . Using a supervision circuit is preferable. MCDI tested and recommends

Altronix PM212. and a 12V battery. A circuit like the Altronix PM212 will insure a constant tension (9-12V preferred), battery

charge and battery supervision

DESCRIPTION Page 6 | 41

Operating guide for Alarm Receiver DECRYPTA3

MCDI Security Products Inc.. Internet: mcdi.com

7055 Jean-Bourdon Avenue, Montreal, QC, Canada H4K 1G7 Telephone: +514-481-1067 Fax: +514-481-1487

Insure that your circuit delivers less than 14V to DECRYPTA3. Significant heat dissipation will result if using a power

source of more than 13.8V. This may damage the unit of reduce life expectancy of DECRYPTA3.

-Verify installation regularly.

-Consult a qualified Electrician prior to connecting DECRYPTA3 If you are using a battery, a battery charger and/or

equipment

Alternative power source 9-12V DC

DECRYPTA3 is shipped with a power adaptor. When another power supply is preferred for the 9-12V DC input, a

lower voltage should be preferred over a higher voltage to minimize heat dissipation in DECRYPTA3.

USB Hub

While testing several units, MCDI did not find a USB hub able to power TWO DECRYPTA3 units. You must power the

units by their 9-12V DC input if you plan to use a USB hub and use the USB hub only for the benefit of data concentration.

Ground post

As as safety for users and the DECRYPTA3 alarm receiver, DECRYPTA3 is provided with a ground post at

the back on the unit. A wire of AWG #14 should be used along with a lug connectors. Ground connection must be maintained

and verified regularly to insure ground to earth is always present.

Best practice in making a ground connection from DECRYPTA3 are to insure a non resistive connection to a known

and tested ground in a well built electrical installation or connect the ground lug of DECRYPTA3 to a metallic water

pipe going to earth or to a rod deeply planted to earth.

Should several DECRYPTA3 units be used it is preferable not to chain units by their ground lugs. A better practice is

to use a ground star technique according to Diagram.

Using a battery charger

MCDI tested and recommends a supervision circuit like Altronix PM212 (altronix.com). This circuit will take 16VAC wall

transformer (Alarm panel transformer) charge a 12V battery, insure supervision and will deliver power from battery when AC

feed is missing.

When using a battery charger, insure that the tension at DECRYPTA3 electrical entry is less than 14VDC. Applying

voltage of more than 14V DC may cause significant heat dissipation within unit. Damages may result and this may reduce life

expectancy of DECRYPTA3

WARNINGS

-DECRYPTA3 does not supervise battery.

-Verify electrical set-up regularly.

-Always use properly mounted and approved cables to connect DECRYPTA3

-Do not use an over charger battery or a battery dispensing more than 14VDC.

-Consult a qualified Electrician prior to connecting DECRYPTA3 If you are using a battery, a battery charger and/or

equipment not provided by MCDI Security Products Inc.

-Damages resulting from power surges of any kind of specifically excluded from DECRYPTA3 warranty.

USING ON-BOARD RELAY :

DECRYPTA3 is equipped with a relay to trigger an external device such as strobe light, dialer, siren upon reception of

an alarm signal.

Terminal posts are located at the back of the unit. Posts: 1 and 2 are Normally Open. Posts 2 and 3 are Normally Closed. Post

2 is the Common. Maximum rating : 110V DC or 125 V AC / 1A UL/CSA rating : 30V DC / 1A 110V DC or 125V AC /

.3 A.

DESCRIPTION Page 7 | 41

Operating guide for Alarm Receiver DECRYPTA3

MCDI Security Products Inc.. Internet: mcdi.com

7055 Jean-Bourdon Avenue, Montreal, QC, Canada H4K 1G7 Telephone: +514-481-1067 Fax: +514-481-1487

Configuring DECRYPTA3 receiver by software

MCDI winExprecium2.exe

There is no switches or jumpers to configure

your card. All settings are done using the setup

program called winExprecium2.exe ( provided

on the media coming with your card ). This

program works under Windows and can be

executed from any disk drive. To use it under

Windows, your Windows drivers must be

installed first and properly configured.

To enter the configuration menu double click

on the icon winExprecium2.exe

The following display will appear :

MCDI Axe and Logger tools

Axe configurator is a universal tool for configuring

MCDI receivers. Currently it supports the following

receivers:

Exprecium (I and II version)

USB DECRYPTA3

The support for other MCDI receivers will be done in a

near future.

Logger is a software tool to log to disk

DECRYPTA3 raw output . Logged data may

be read by word processors and Excel for reporting or

/and analysis.

1. JAVA RUN TIME ENGINE Installation

If you don’t have Sun’s JRE installed you can install it

from the CD. It is located in \

Configurator_logger\Java_installer\ directory. To

install, run the installer program j2re-1_4_2_04-

windows-i586-p.exe. Under Windows XP you will

need administrative privileges in order to install JRE.

DESCRIPTION Page 8 | 41

Operating guide for Alarm Receiver DECRYPTA3

MCDI Security Products Inc.. Internet: mcdi.com

7055 Jean-Bourdon Avenue, Montreal, QC, Canada H4K 1G7 Telephone: +514-481-1067 Fax: +514-481-1487

2. Installation of MCDI Axe configurator 0.1.0

Requirements:

MS Windows XP

Sun’s Java Runtime Environment (JRE) 2. Located on CD.

Axe Configurator Installation

The installation procedure is very simple. To start the installation, run the installer program, Axe_install_0.1.0.exe:

1. It will prompt you for the language you want the installer to run in.

2. The license is displayed. Read it carefully and then click on “I Agree” to agree with the licensing terms.

3. Select the directory in which the Axe Configurator will be installed or accept the default settings, then click on “Install”.

4. You will see the progress of the installation. If you want to see where and which files are being copied, click on “Show

Details”.

5. Press “Close” when finished

A few shortcuts are created for your convenience:

1. On your desktop

2. In the Start Menu, under Start Programs MCDI Axe Configurator

Un-installation

You can un-install Axe Configurator in two ways:

From the Control Panel:

select Start Settings Control Panel. Then select “Add or remove programs”, choose “Axe

Configurator” from the list and follow the un-installation procedures.

Directly

: select Start Programs MCDI Axe Configurator Uninstall and follow the un-installation procedures.

Usage

At the startup, you will see the following welcome screen to

configure a device, select it from the device list:

NOTE: The configurator tries to detect what kind of receiver

is connected to the PC. Yet sometimes it’s necessary to

actually start the process of retrieving the configuration in

order to completely determine what kind of receiver it is.

Thus, in the device menu you may see:

“Exprecium” for Exprecium I and II cards

“Serial” for any device attached to physical COM port, for example, Decrypta or the serial port connection of DECRYPTA3.

“USB DECRYPTA3for the USB connection of the DECRYPTA3.

When you select receiver, its configuration settings will be retrieved, and you will see different configuration screens according to

the type of the receiver (see section “Configuration screens”).

Setting language of the Axe Configurator

You can select English, French, Spanish, German, or Russian. To set the language, select it from the menu Options  Language.

Starting other MCDI software from Axe Configurator

You can start WinSAMM, WS Receiver, Traffic Logger, or WinCOM from the Traffic Connect To menu. To set paths to those

programs, select Traffic Settings.

DESCRIPTION Page 9 | 41

Operating guide for Alarm Receiver DECRYPTA3

MCDI Security Products Inc.. Internet: mcdi.com

7055 Jean-Bourdon Avenue, Montreal, QC, Canada H4K 1G7 Telephone: +514-481-1067 Fax: +514-481-1487

Receiver configuration

When a particular device is selected and its configuration screen is shown (see section “Configuration screens”), the following

actions are available:

Submit configuration

Press on the “Submit” button or, equivalently, select File Submit to send the configuration to the receiver, and close the

configuration screen.

NOTE: When the configuration is submitted the receiver is set to

the system time displayed in the “Synchronization” section:

Discard configuration

Press on the “Discard” button or, equivalently, select File Discard to discard any changes made and close the configuration

screen.

Save configuration

To save the current configuration to a file, select File Save.

Open a saved configuration

To load the configuration from a file, select File Open.

NOTE: File extensions are different for different receiver types. You will not be able, for example, to load an Exprecium I

configuration file (*.exp) while configuring an Exprecium II (*.expdec2).

Load Presets

For some receivers, there are preset configurations stored in the “presets” subdirectory of the Axe Configurator directory. You

will see the available presets under File Presets.

Configuration screens

Serial/USB DECRYPTA3

Axe configurator recognizes

Decrypta 3 connected on USB port

of PC. Some options specific to

Decrypta 2 will be showned in this

window when Axe recognizes a

Decrypta 2 unit. Axe will also render

more information from USB

connection, namely receiver name,

firmware version installed in receiver

and serial number of unit. USB port

and COM port redirection (virtual

serial port redirection) are indicated

in the Device drop down menu.

Table des matières

Autres manuels MCDI Récepteur

MCDI

MCDI DECRYPTA Manuel utilisateur

Manuels Récepteur populaires d'autres marques

Garmin

Garmin GA 23 Manuel utilisateur

Aiphone

Aiphone PS-12F Manuel utilisateur

IMES

IMES TCS-01CA-PMI Manuel utilisateur

BWI Eagle

BWI Eagle AIR-EAGLE SR Manuel

AMIMON

AMIMON AMN12310 WHDI Manuel utilisateur

Dual

Dual DMCPA79BT Mode d'emploi

Sound Associates

Sound Associates SA652P Manuel utilisateur

Sherwood

Sherwood NewCastle R-772 Manuel utilisateur

Audio

Audio A10-RX Series Manuel utilisateur

AllSee

AllSee PushShare PSRV1.1 Manuel utilisateur

DEMAG

DEMAG DRC-DR D2 Manuel utilisateur

Teleco

Teleco TVRCL868A02 Manuel utilisateur

Bosch

Bosch RF3222E Manuel utilisateur

Kramer

Kramer 631R Manuel utilisateur

Xpress

Xpress xmc10 Manuel utilisateur

JVC

JVC KD-MR1BTS Manuel utilisateur

Omega Engineering

Omega Engineering UWTC-REC3 Manuel utilisateur

e-survey

e-survey E300 Pro Manuel utilisateur