Mazda 0000-8G-K02 Manuel utilisateur

AS 090-M11357cmc1105RevA

Page 1 of 4

Genuine Accessories

Installation Instructions

Part Number

0000-8G-K02

Applicable Models:

2004 Mazda RX8 Aero

Package Contents

Front Mask

U-Nut (Qty. 8)

Tools Required

Stubby Phillips

Screwdriver

Hood Cover (Qty. 1)

Snap Head Screw (Qty. 8) Front End Cover (Qty. 1)

0Before Installation

A. Area to be covered by mask must be clean. It is recommended that you wash and wax vehicle prior to installation.

B. Both vehicle and mask must be completely dry prior to installation. If moisture under mask is allowed to dry on

vehicle, paint may cloud.

C. Any repainted surfaces in contact with mask must be allowed to cure completely. Consult paint manufacturer or

repair facility if you are not sure.

1Install Hood Cover

A. With hood open, stretch hood cover (A)

onto hood, pulling each side one or two

inches at a time, until corners fit snugly.

Install hooks on ends of straps (B) into

corresponding holes in hood. Pull

evenly on ends of adjustable straps (B)

until tight. Secure loose ends in elastic

loops.

Washer (Qty. 8)

Page 2 of 4

AS 090-M11357cmc1105RevA

2Remove wheel well fasteners

A. Using stubby phillips screwdriver, remove five plastic

fasteners along front edge of both front wheel wells.

A. In both front wheel wells, lift wheel well liner to reveal holes.

B. Slip u-nuts (C) over top two and bottom two holes in metal edge,

making sure that holes are aligned.

C. Release liner to its original position. Using a stubby phillips

screwdriver, install washer (D) and snap head screws (E) into top

two and bottom two holes in each wheel well. Reinstall

original fastener into unoccupied middle hole.

3Install wheel well hardware

5Install wheel well

attachments

A. Press snaps (K) onto snap head screws

(E) in both front wheel wells.

GFG

4Install upper attachments

A. With hood open, lay front end cover over front of vehicle. On both sides of

vehicle, slide pockets (F) over front corners of fenders. Care

should be taken to prevent ripping of pockets (F).

B. Attach clips (G) to edge of fender rails.

C. On both sides of vehicle, insert pads (H) in slot under headlights.

D. Attach clips (J) to back inside edge of metal at center of vehicle under hood.

Page 3 of 4

AS 090-M11357cmc1105RevA

7Install bottom attachments

8Post Installation Inspection

A. Close hood and check alignment between hood

cover and front end cover along seam (between

fender and hood). If adjustment is necessary, adjust

the hood cover by adjusting the hood cover straps.

Refer to step 1.

B. If mask should flap due to high speed or wind

conditions, adjust or remove mask completely.

9Care and Cleaning

A. Always remove mask before washing vehicle.

B. Hand clean mask using mild soap, rinse thoroughly with

clean water and line dry completely. Do not machine dry!

C. Use Mazda Vinyl/Leather Protectant (or equivalent) to

preserve color and finish.

D. WARNING: Running up on curb will damage this product.

Manufacturer will not be responsible for damage to product

due to accident or misuse.

Place in vehicle glove compartment.

A. Attach clips (O) to back edge of facia in fog light and air intake areas. Attach clips (P) and elastics with hooks (Q) to back

edge of bumper facia.

OPPP

10x

6Install air intake attachments

A. Insert pads (L) into slot located between edge of front facia and top edge of grille area. Insert velcro loop (M) into nearby hole

in grille area and attach velcro hook (N) located at underside edge of bumper facia.

Autres manuels Mazda Accessoires automobiles

Mazda

Mazda Connect Manuel utilisateur

Mazda

Mazda Bluetooth Handsfree System Manuel utilisateur

Mazda

Mazda C830-V7-050A Manuel utilisateur

Mazda

Mazda 4100-78-828A Manuel utilisateur

Mazda

Mazda 0000-8G-K01 Manuel utilisateur

Mazda

Mazda 0000-8C-Z02 Manuel utilisateur

Mazda

Mazda GENUINE SIDE UNDER SPOILER Manuel utilisateur

Mazda

Mazda CT-L1005 Guide d'installation

Mazda

Mazda CX-9 Manuel utilisateur

Mazda

Mazda 6 GJ 2.2 D 2012 Manuel utilisateur

Mazda

Mazda Bluetooth Mobile Phone Kit Manuel utilisateur

Mazda

Mazda DN4J-V7-110 Manuel utilisateur

Mazda

Mazda 0000-8P-R04 Manuel utilisateur

Mazda

Mazda TD91 79 CFZ Manuel utilisateur

Mazda

Mazda CX-9 Manuel utilisateur

Mazda

Mazda DC3L-V1-370A Manuel utilisateur

Mazda

Mazda A2DP Manuel utilisateur

Mazda

Mazda CX-5 Manuel utilisateur

Mazda

Mazda 0000-8G-N03 Manuel utilisateur

Mazda

Mazda 0000-8E-R10 Manuel utilisateur

Mazda

Mazda 0000-8K-L05 Manuel utilisateur

Mazda

Mazda 0000-8G-K05 Manuel utilisateur

Mazda

Mazda DF71-V4-085 Manuel utilisateur

Mazda

Mazda Highbay BY007P Manuel utilisateur

Manuels Accessoires automobiles populaires d'autres marques

James Baroud

James Baroud Odyssey Manuel utilisateur

Motorola

Motorola i50sx Manuel utilisateur

Yakima

Yakima 9MM STANDARD BIKE MOUNT Manuel utilisateur

Feniex

Feniex T3 Manuel utilisateur

Renault

Renault 77 11 423 180 Manuel utilisateur

Kia

Kia E8300-4D000 Manuel utilisateur

Brink

Brink 756843 Manuel utilisateur

Whispbar

Whispbar K085W Manuel utilisateur

v.link

v.link CI-VL2-PC-HSD Manuel utilisateur

Viking

Viking Stack-Rack Guide de configuration rapide

Aries

Aries 203015 Manuel utilisateur

Choetech

Choetech AT0005 Manuel utilisateur

ZZ2

ZZ2 ZZAIR-PRO Manuel utilisateur

Holman

Holman 4A80L Manuel utilisateur

Thule

Thule 2075 Manuel utilisateur

Motorola

Motorola T325 Manuel utilisateur

TAUBENREUTHER

TAUBENREUTHER 16-3950 Guide d'installation

DV8

DV8 FBJL-02 Manuel utilisateur