Maytag Neptune MAH9700 Manuel utilisateur
Maytag Neptune
27” Front Load Washer
L2005-004
© Maytag Technical Training Services 2005
Miami Lakes
Education Center
5780 NW 158
th
St
Miami, FL 33014
305-557-1100 EXT 2332
Center for Manufacturing Excellence
3000 Log City Trail
Galesburg, IL 61401
309-345-3501
Los Mendanos College
2700 East Leland Rd
Pittsburg, CA 94565
925-439-2181
Tulsa Technology Center
3850 North Peoria
Tulsa, OK 74147-7200
918-828-2038
Louisiana Technical College
111 Pride Dr
Hammond, LA 70404-0489
985-543-4123
Appliance Repair Institute
275 South G St
San Bernadino, CA 92410
909-888-3600
Elizabethtown Technical College
610 College St Rd
Elizabethtown KY 42701
270-769-2371
Kwantlen University
College
12666 72
nd
Ave
Surrey, BC
Canada V3W2M8
604-599-2962 Bay State School of Technology
225 Turnpike St
Canton, MA. 02021
888-828-3434
Hibbing Community College
1515 East 25
th
St
Hibbing, MN. 55746
218-262-7231
Maytag Authorized Training Centers
1
Slide 1
Maytag Neptune 27” Front Load Washers
Premium II – MAH9700 - (Direct Drive Motor – Slope Console)
Premium I – MAH8700 – (Belt Drive Motor – Slope Console)
Entry Level– MAH6700 - (Belt Drive Motor - Flat Front Console- Stackable)
Slide 2
Major Differences
Top Spin Speed;
9700–1200RPM
8700–1100 RPM
6700–1000 RPM
Noise Reduction
9700 Direct drive motor, 2 tuned absorbers
8700 2 tuned absorbers
6700 1 tuned absorber
Weights
9700 uses two weights attached to the front of outer tub
6700 & 8700 use four weights. Two attached to the front of outer tub, one behind the spinner pulley
and one mounted to the right rear side of the outer tub
Slide 3
Maytag Neptune 27” Front Load Washer MAH9700
This training presentation is
based on the MAH9700.
Differences between the
9700 and 8700 machines
will be highlighted
Tub is tilted 10 degrees
to ease unloading
2
Slide 4
Maytag Neptune Washer MAH9700
Dimensions Base Cycles
Washer Width 27” Sanitary 151 Degrees F
Washer Depth 30.75” Super Wash
Washer Height 38” Normal
Washer Weight 191 LBS Whites
Pedestal/Riser (MAL1800AX*) 13” Wrinkle Control
Features Colors
Capacity (cu.ft) 3.81 Delicates
Controls LED Hand Wash
Motor Type Direct Drive Quick Wash
Spin Speeds 6 Enviro Plus
Water level Control IntelliFill Options
Water Temp Combinations 6 Prewash
ATC Control Stain Treat
Soil Level Selections Heavy, Med., Light Extra Rinse
Spinner Stainless Extended Spin
Self Clean Lint System Rinse & Spin
Internal Heater 900 Watts Spin Only
End of Cycle Chime High, Med., Off Spin Speeds Approximate RPM
Delay Wash Up to 19 Hr. Max Extract Plus 1200 RPM
Dispensers High 1000 RPM
Detergent Dispenser Pre and Main Medium 800 RPM
Bleach Dispenser 100ml Gentle 600 RPM
Fabric Softener Dispenser Low 400 RPM
Child Lock Out Control Lock Drain only 0 RPM
Tumble Pattern
Normal 35 Times per Minute 15” pedestal and Drawer MAL1800AXW/M
Hand Wash 5 Times per Minute
Energy Consumption 266 Kw/H per year Colors White, Platinum
Water Consumption 9.9 to 15.9 Gallons
3
Slide 5
Note: The Power Point Presentation and Participant’s Guide for this training session were developed
using prototype machines. There might be slight cosmetic differences between the product pictured and
the current production units. Always refer to the Technical Data Sheet for detailed information for the
product you are servicing.
Slide 6
Always follow all safety
and caution warnings
found on the machine and
in the installation and
customer use manuals!
Location for the Technical
Data Sheet
Slide 7
The installation
process for the
27” is similar to
the 24” product
that preceded it.
4
Slide 8
The installation package
contains the fill hoses, a
combination wrench for
removing the shipping
bolts and adjusting the
leveling legs, filler plugs
and a drain hose bracket.
Slide 9
Remove the four 10mm
shipping bolts and spacers
Slide 10
Save the shipping bolts and spacers and
installation instruction in case of a future move.
5
Slide 11
Install the filler plugs supplied in the installation kit.
Slide 12
Leg in Shipping Position
After leveling, make sure to
tighten the locking nut against
the base. Failure to do so will
cause excessive vibration
Tighten Nut
Level the machine side
to side and front to back
The washer must be installed on a sturdy floor and leveled.
Make sure the locking nuts are tightened against base
6
Slide 13
MAH 8700 Timer
MAH 9700 Timer
The 9700 washer
timer features two
additional cycles
not found on the
8700; Sanitary and
Enviro Plus
The Sanitary cycle delays during the first wash to heat the wash water. A 900 Watt heating
element located in the bottom of the outer tub is used to raise the water temperature to 151 degrees F.
As soon as a 151 degree F. temperature is reached the cycle resumes. The machine will delay up to 69
minutes if necessary to achieve SaniTemperature. The purpose of the 151 Degree water temperature is
to help eliminate bacteria and improve cleaning performance.
The Enviro Plus cycle uses less energy and less water than the Normal Cycle.
Slide 14
MAH 8700
Table des matières
Autres manuels Maytag Rondelle
Maytag
Maytag MAV9504EWW Manuel
Maytag
Maytag 2612990 Manuel utilisateur
Maytag
Maytag MAT15MN Manuel utilisateur
Maytag
Maytag MAH-24 Manuel utilisateur
Maytag
Maytag LAT9206B Manuel utilisateur
Maytag
Maytag Atlantis MAV6451AWQ Manuel utilisateur
Maytag
Maytag MVWC200 Manuel
Maytag
Maytag LAT9356 Manuel utilisateur
Maytag
Maytag W10280550B Manuel utilisateur
Maytag
Maytag 4KMVWC410JW1 Manuel utilisateur
Maytag
Maytag MAV8757AWW Manuel utilisateur
Maytag
Maytag W11197735B Manuel utilisateur
Maytag
Maytag NEPTUNE WASHER Manuel utilisateur
Maytag
Maytag BRAVOS XL MVWB750YW Instructions de montage
Maytag
Maytag NEPTUNE TL Manuel utilisateur
Maytag
Maytag W11099670B Manuel utilisateur
Maytag
Maytag BRAVOS MTW6600TB0 Manuel utilisateur
Maytag
Maytag MAT20MNBKW Manuel utilisateur
Maytag
Maytag AUTOMATIC WASHER Manuel utilisateur
Maytag
Maytag MHW9000YG Manuel utilisateur
