Maxxima M20487 Manuel utilisateur

[email protected] 866-MAXXIMA (629-9462) www.maxxima.com 125 Cabot Court Hauppauge, NY 11788

Page 4 of 4 Page 1 of 4

[email protected] 866-MAXXIMA (629-9462) www.maxxima.com 125 Cabot Court Hauppauge, NY 11788

CAUTION

• Prior to drilling holes into the vehicle for installation, ascertain that no internal

components of the vehicle will obstruct the placement or mounting of the LED minibar.

For all wire passage holes, apply caulk or install grommets.

• Avoid installing the minibar or routing any cables in the vicinity of the vehicle's airbags.

Any interference could hinder the proper deployment of the airbags, thereby

compromising their intended effectiveness.

• Carefully select the mounting location for the minibar, avoiding areas that may impair

visibility or distract the vehicle's operator. Improper placement could obstruct the

operator's view or divert their attention, potentially leading to serious accidents.

• For cleaning the outer lens of the minibar, only use a mixture of soap and water.

Utilizing other chemicals may lead to premature cracking or discoloration of the lens.

Damaged lenses can significantly impede the minibar's functionality.

Regularly inspect and operate the minibar to ensure it is working optimally.

• Refrain from looking directly into the minibar while it is operational. The high-intensity

LEDs used in this device can cause temporary blindness or even permanent eye damage.

WIRING/ELECTRICAL

Operation using the cigarette plug (M20487):

• Connect the minibar cigarette adapter to the cigarette lighter outlet.

• Press the first switch to power the lightbar. The red LED should illuminate.

• Cycle through the patterns by pressing the other switch for 1 second at a time.

• Revert to pattern 1 by pressing the pattern selector for 5 seconds.

NOTE: When the lightbar is turned off and powered on again, the previously set lightbar

pattern will illuminate on the lightbar.

Operation without using the cigarette plug (M20488):

BLACK - Ground ------------------

RED - Main Power ----------------

YELLOW - Trigger Wire ---------

Extend to the vehicle ground.

Extend to a switch and then to the POSITIVE battery

terminal. Fuse appropriately.

To cycle to the next pattern, tap to +VDC for 1 second.

Yellow

Red

Black

Wire color

Wiring Diagram

12/24VDC (+)

Ground (-)

(-) (+)

FLASH PATTERNS

Pattern

Flash Pattern Description

Single [125FPM] (Class 1)

Single [75FPM] (CA13, Class 1)

Double (Class 1)

Triple

Clockwise Rotation

Symmetrical Rotation

Counterclockwise Rotation

Pattern7 x 4cycle + 3 Single Flash

Single (Split Left & Right) Split

Triple (Middle + Two Ends + Full)

LED MINIBAR INSTRUCTION MANUAL

M20487/M20488

FLASH PATTERNS

Pattern

Flash Pattern Description

Go and Back “C” shape running

Progressive (Left + Right)

Quad (Left & Right) Split

Double (Left & Right) Split

Quint (Left & Right) Split

Strobe (Left & Right) Split

Fast & Slow Double (Left & Right) Split

Fast & Slow Quad (Left& Right) Split

Momentary switch (optional)

Page 2 of 4 Page 3 of 4

[email protected] 866-MAXXIMA (629-9462) www.maxxima.com 125 Cabot Court Hauppauge, NY 11788 [email protected] 866-MAXXIMA (629-9462) www.maxxima.com 125 Cabot Court Hauppauge, NY 11788

PERMANENT/BRACKET MOUNTING

NOTE: Before beginning the minibar installation, ensure that the mounting location is clear

of all obstructions. Possible obstructions include but are not limited to: roof support

members, wire harnesses, airbags, vehicle trim components. It is recommended that the

vehicle’s headliner is removed before drilling. If the headliner remains in place, the

drill bit may puncture the headliner and cause damage.

Tools needed for installation include a drill bit with a diameter of 1/4”or an 8mm

(5/16“) for the side bracket. A socket or wrench is required as well.

Before securing the minibar, the wire harness will need to be routed. This hole must be about

1/4” in diameter for the wire to pass through. It is recommended that an appropriately

sized grommet be placed into the hole before the wire is passed through. With the wire in

place, seal the grommet and wire combination with silicone for waterproofing. The grommet

will prevent premature damage to the minibar’s wire.

Choose one of the three mounting bracket styles and attach the bracket to the minibar using

the provided round gasket pad and bolt. To position the minibar, place it in a suitable location

and mark the four minibar mounting holes. Then remove the minibar and drill the appropriate

holes. Now, insert the 4 bolts through the bracket. Place the gasket between the

minibar’s bracket and the vehicle’s surface. Feed the bolt through the mounting holes and

secure the minibar using the provided washers and nut. Refer to the drawing below for

guidance. Finally, tighten the nuts with the socket or wrench until the minibar is firmly

secured to the vehicle.

MAGNET MOUNTING

NOTE: We advise against using any magnetically mounted warning device, including this

minibar, on the exterior of a vehicle moving at high speeds (over 30 mph). This practice is

not recommended and any resulting damage or safety issues are solely the responsibility of

the user. It is advised to remove the minibar from the vehicle's exterior before setting the

vehicle in high speed motion.

Before mounting the lightbar using the magnetic hardware, ensure the mounting surface is

thoroughly clean. For optimal adhesion, clean the surface with a solution composed of

isopropyl alcohol and water, then dry the surface completely. Once prepared, position

the lightbar in its designated location, making certain that all the magnets are making full

contact with the vehicle’s surface. Proceed to route the wire as necessary and plug it into the

vehicle’s cigarette lighter socket for power.

SPECIFICATIONS

LED Color

Voltage

Max Power

Flash Pa�erns

Amber or Amber/White

12V - 24V

55W

398

217

Bolt MountingSide Bracket Mounting

Bracket Mounting

24.7 47

17.5 47

400

322

132

206

189.9

206

400

Magnet Mounting

SAE

Material

Mount

J845 Class 1A

M20487: Magnet

M20488: Bracket (2x), or Bolt

All dimensions are in millimeter (mm)

PATTERN ON/OFF

Bolt Mounting Pill Pack

Side Bracket Pill Pack

Bracket Pill Pack

Minibar

Spring Washer

Plas�c Washer

Flat Washer

Magnet Disk

(Ø66*8.5, M6)

4600

9.6

Ce manuel convient aux modèles suivants

Autres manuels Maxxima Équipement d'éclairage

Maxxima

Maxxima M85427R-YCL Manuel utilisateur

Manuels Équipement d'éclairage populaires d'autres marques

Brizo

Brizo 8SP-MU-4 Manuel utilisateur

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manuel utilisateur

IKEA

IKEA BJÖRKSPIREA Manuel utilisateur

Laserworld

Laserworld Evolution Series ES-400RGB Manuel utilisateur

Alien

Alien RG STAR Manuel utilisateur

EuroLite

EuroLite LED B-40 Manuel utilisateur

Qazqa

Qazqa Suplux SL 3 Black 103062 Manuel utilisateur

Commercial Electric

Commercial Electric 54568141 Manuel utilisateur

CREE LIGHTING

CREE LIGHTING 304 Series Manuel utilisateur

Goobay

Goobay 49867 Manuel utilisateur

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manuel utilisateur

Alkalite

Alkalite Krypton KT-81 Manuel utilisateur

Clas Ohlson

Clas Ohlson GU10 Manuel utilisateur

DTS

DTS DELTA 10 F Manuel utilisateur

ring

ring Solar Steplight Manuel utilisateur

One Stop Gardens

One Stop Gardens 57696 Instructions de montage

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manuel utilisateur

SIREM

SIREM Swimeo A2 Manuel utilisateur