Maxcess Performance Series Manuel utilisateur

Performance Series

Knifeholder

Quick Reference Guide

Tidland Quick Reference – Easy Glider Install 01/04/11 www.maxcessintl.com 1-800-426-1000

Easy Glider Linear Bearing

READ FIRST

•Do not remove the factory-installed short rail

section from the linear rail.

•This rail section must be used to install the

knifeholder onto the guide bar rail.

•Failure to use this rail section when installing the

knifeholder may result in bearing damage and void

bearing warranty.

Safety Recommendation

Remove blade cartridge from knifeholder before handling.

Installing the Knifeholder on the Guide Bar

1. Choose at which the end of the guide bar the

knifeholders will be mounted.

2. At the mounting end only, locate and remove the

#10-32 UNF end stop screw on the face of the

guide bar.

3. Do not remove the short rail from the

knifeholder bearing.

4. Turn the brake knob counterclockwise to unlock.

5. Push the brake shoe up into the back plate if

protruding.

6. Install the knifeholder:

a. Hold the knifeholder and short rail section

together. Carefully place the rail section

into the keyway on the guide bar.

b. Align the short rail section with the fixed

bearing rail on the guide bar.

c. Slide the knifeholder onto fixed bearing rail.

7. Remove short section of bearing rail from the guide

bar. Note: Keep the short rail for future

maintenance and knifeholder removal.

8. Repeat Steps 2-8 until all knifeholders are installed

on the guide bar.

9. After all knifeholders are installed, reinstall the #10-32 UNF socket head cap screws in the end stop.

10. Reinstall blade cartridges on knifeholders.

11. Turn the function control knob to red (retract) position on all knifeholders.

Performance Series

Knifeholder

Quick Reference Guide

Tidland Quick Reference – Easy Glider Install 01/04/11 www.maxcessintl.com 1-800-426-1000

Easy Glider Linear Bearing

READ FIRST

•Do not remove the factory-installed short rail section

from the linear rail.

•This rail section must be used to install the

knifeholder onto the guide bar rail.

•Failure to use this rail section when installing the

knifeholder may result in bearing damage and void

bearing warranty.

Safety Recommendation

Remove blade cartridge from knifeholder before handling.

Removing the Knifeholder from the Guide Bar

1. Remove the blade cartridge.

2. Choose at which end of the guide bar the

knifeholder will be removed; move the

knifeholder just to the end of the fixed rail

on the guide bar.

3. Locate and remove the #10-32 UNF

screw from the end stop on the face of

the guide bar.

4. In the space at the end of the guide bar,

align the short piece of rail (received with

each knifeholder bearing mount) with the

fixed rail and transfer the knifeholder from

the fixed rail to the short rail.

5. Hold the knifeholder and the short rail

together and carefully remove them from

the guide bar. Do not remove the short

rail from the knifeholder bearing

mount. You will need it to reinstall the

knifeholder on the guide bar.

TIP:

Secure the short rail to the linear

bearing with a small piece of tape to

retain the bearing balls during

maintenance.

Autres manuels Maxcess Équipement industriel

Maxcess

Maxcess TIDLAND Roll Restorer Manuel utilisateur

Maxcess

Maxcess FIFE D-MAXE 2 Manuel utilisateur

Maxcess

Maxcess MAGPOWR TS Load Cell Manuel utilisateur

Maxcess

Maxcess FIFE-500 Manuel utilisateur

Maxcess

Maxcess MAGPOWR Manuel utilisateur

Maxcess

Maxcess Tidland Performance Series Instructions d'installation et d'utilisation

Maxcess

Maxcess FIFE-500-XL Manuel

Maxcess

Maxcess Tidland Advantage Series Manuel utilisateur

Maxcess

Maxcess VERSATEC S15 Instructions d'installation et d'utilisation

Maxcess

Maxcess Fife-200 Manuel

Maxcess

Maxcess MAGPOWR C1 Manuel utilisateur

Maxcess

Maxcess MAGPOWR GTS Load Cell Manuel utilisateur

Maxcess

Maxcess GTS Manuel utilisateur

Maxcess

Maxcess MAGPOWR TLC-B Load Cell Manuel utilisateur

Maxcess

Maxcess FIFE-500 Manuel utilisateur

Maxcess

Maxcess Tidland Raptor Series Manuel utilisateur

Maxcess

Maxcess MAGPOWR Perma-Tork HC2 Manuel utilisateur

Maxcess

Maxcess Tidland Force5 Chuck Manuel du propriétaire

Maxcess

Maxcess TIDLAND D6X Manuel utilisateur

Maxcess

Maxcess FIFE D-MAXE 1 Manuel utilisateur

Maxcess

Maxcess FIFE-500 Manuel d'instructions

Maxcess

Maxcess MAGPOWR LC500G Manuel utilisateur

Maxcess

Maxcess MAGPOWR Perma-Tork HB6-1 Manuel utilisateur

Maxcess

Maxcess Magpowr CL1-5 Manuel utilisateur

Manuels Équipement industriel populaires d'autres marques

ABB

ABB Unifix AD Manuel

Mark 7

Mark 7 Evolution Manuel utilisateur

Husky

Husky HyPET Manuel utilisateur

bora

bora PM-1800 Manuel utilisateur

Grizzly

Grizzly T32428 Manuel utilisateur

Siemens

Siemens 8MF1 Series Manuel utilisateur

ABB

ABB HT610965 Manuel utilisateur

ABB

ABB SafeLink Manuel utilisateur

Phoenix

Phoenix PHX-150 Manuel utilisateur

ABB

ABB A165-L32 Manuel utilisateur

ABB

ABB HT842936 Manuel utilisateur

Rioned

Rioned UrbanJet Manuel utilisateur

Hermetica

Hermetica 10 Series Manuel utilisateur

HORNER

HORNER OEE Solution Manuel utilisateur

Hammerhead

Hammerhead HG375 Manuel utilisateur

SCHUNK

SCHUNK VERO-S NSE-A3 138 Instructions d'utilisation

ABB

ABB HT566657 Manuel utilisateur

Webasto

Webasto GSE CAN Manuel utilisateur