Matrix Retail E50 Manuel utilisateur

E30 and E50

Service Manual

Matrix Retail E50 Matrix Retail E30

Specification

Production Browse

Contents

CHAPTER 1: SERIAL NUMBER LOCATION………………………………………………………………..4

CHAPTER 2: TROUBLESHOOTING

2.1 Electrical Diagram…………………………………………………………………………………………...5

2.2 Board Connector Location …………………………………………………………………………………..6

2.3 Error Code Summary ………………………………………………………………………………………...8

2.4 Troubleshooting

2.4.1 Console Does Not Light up……………………………………………………………………………....9

2.4.2 Speed Does Not Display...……………………………………………………………………………….10

2.4.3 Heart Rate Issues………………………………………………………………………………………..11

2.4.4 Quick Key Issues ...………………….…………………………………………………………….. …..12

2.4.5 Noise Issues…………………………………………………………………………………………………………………………….13

2.4.6 No Resistance Or Incorrect Resistance……………………………………………………………….14

CHAPTER 3: PART REPLACEMENT GUIDE

3.1 Console Replacement…………………………………………………………………………………………………………………..16

3.2 Heart Rate Grip and Quick key Replacement……………………………………………………………………………....18

3.3 Cup Holder Replacement……………………………………………………………………………………………………………..19

3.4 Console Mast Replacement………………………………………………………………………………………………………….20

3.5 Handle Bar Replacement……………………………………………………………………………………………………………..21

3.6 Link Arm Replacement……… …………………………………………………………………………..22

3.7 Side Cover Replacement …………………………………………………………………………………………………………..…23

3.8 ECB Motor Board Replacement …………………………………………………………………………………………………..24

3.9 LCB board Replacement…..…………………..……………………………………………………… ..25

CHAPTER 1: Serial Number Location

1.1 Serial Number Location

MATRIX E30/E50 EP FRAME

SERIAL NUMBER

CHAPTER 2: Troubleshooting

2.1 ELECTRICAL DIAGRAM

E30 Frame: (Fig.1)

E50 Frame (Fig.2)

(Fig-1)

CHAPTER 2: Troubleshooting

2.2. Board Connector Instruction:

2.2.1 ECB (E30):

ECB (Fig-1)

CN1 Speed sensor connection

CN2 Power adaptor connection

CN3 Console connection

2.2.2 Lower Control Board Connections

LCB (Fig-2)

Fig-2

AC1&AC2

JP1

JP02

JP03

AC power line input

LCB to console

Speed sensor

Resistance control

2.3 Error Code Summaries:

Code Description Symptom Solution

1 CONSOLE DOES NOT LIGHT

A .The power switch is in the on position, but

the console will not turn on.

b. The console is damaged or the console

cable is not connected properly.

c. Connection to the terminals on the lower

control board or console.

d. The lower control board is damaged and

does not output voltage.(E50)

e. The power adaptor is damage. (E30)

See section

2.4.1

2 SPEED DOES NOT DISPLAY The speed value does not display on console. 2.4.2

3 HEART RATE ISSUES A .Power contact between the user and HR

grips or HR strap.

b. The HR strap is at a low battery status.

c. The HR strap is damaged.

d. The HR grips are damaged.

e. The HR cannot display value.

2.4.3

4 QUICK KEY ISSUES a. No contact between keypad and overlay.

b. Keypad malfunction.

c. No contact between Keypad to console.

2.4.4

5 NOISE ISSUES Slapping / squeaking sound with each

footstep.

2.4.5

6 NO RESISTANCE OR

INCORRECT RESISTANCE

a. The resistance does not change.

b. The resistance is reversed or too heavy.

c. The keypad is damaged.

d. The console cable is either not connected

to the console or LCB or is damage.

e. The ECB is damaged.

2.4.6

CHAPTER 2: Troubleshooting

2.4.1 TROUBLESHOOTING –CONSOLE DOES NOT LIGHT UP

SOLUTION:

1. The outlet the machine is plugged into is functional.

2. The correct power cord is being used. Only use the power cord included or provided by Customer

Tech Support.

3. The power cord is not pinched or damaged and is properly plugged into the outlet and the machine.

4. Remove the console and check if the console cable has good connected with the console.

Test console cable for 12VDC between pin1 & pin8. If power and connection is good, replace console.

5. Check to see if the console upper cable and console lower are connected well.

6. Remove the side cover and check to see if the cable is connected well.

7. For E30

7.1 Check to see if using correct adaptor: output 12VDC 2A.

7.2Remove the ECB to console cable (see Page7 figure 1). Use multi-meter to check the ECB CN3

Pin1/Pin2 (Positive) and Pin 8 (GND) if cannot see voltage +12 VDC. Install new ECB.

1 2 3 4 5 6 7 8

+12V +12V AD2 NC NC BD2 GND GND

CN3

For E50

7.3. Unplug the console cable from the LCB (see Page12 figure-2). Use multi-meter to check the

LCB JP1 Pin1 (Positive) and Pin 8 (Negative) to see if voltage is +12 VDC.

7.4 If a cannot see +12VDC, connect the LCB to Console cable. If still cannot see light on the screen,

the console is damage, install new console..

CHAPTER 3: Troubleshooting

2.4.2 TROUBLESHOOTING – SPEED DOES NOT DISPLAY

SOLUTION:

For E30

1. Unplug power adaptor, remove the console, and check that all connections to the console are secure

and not damaged or pinched.

2. Remove the side cover and check to see if the sensor wire (CN01) is connected well and not damaged.

(Fig.1)

3. Check to see if one corner of the sensor is aligned with the magnet and ensure that the distance is less

than 5mm.(Fig-1)

4. Test speed sensor with multi-meter in Ohms on Pin1 & Pin2. While passing by magnet, take continuity

readings, open and close, and see if console can display speed.

5. Install new ECB Page7 (Fig-1) to see if console can display speed.

If still cannot display speed value, replace the console.

For E50

1. Unplug power cord, remove the console, and check that all connections to the console are secure and

not damaged or pinched.

2. Remove the side cover and check to see if the sensor wire (LCB JP02) is connected well.-(fig-2)

3. Check to see if one corner of the sensor is aligned with the magnet and ensure that the distance is

less than 5mm. (Fig-3)

5. Install new LCB Page7 (Fig-2) to see if console can display speed value. If still cannot display speed

value, replace the console.

Fig.1 Fig-2 Fig-3

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Matrix vélo elliptique

Matrix

Matrix bve CAB-MATRIX-V600E Manuel utilisateur

Matrix

Matrix LIFESTYLE Manuel utilisateur

Matrix

Matrix E5xc Manuel utilisateur

Matrix

Matrix MX-A5x Manuel utilisateur

Matrix

Matrix A7xe Manuel utilisateur

Matrix

Matrix E5x-02 Manuel utilisateur

Matrix

Matrix E1X Manuel utilisateur

Matrix

Matrix Stepper Manuel utilisateur

Matrix

Matrix E3X-01 Manuel utilisateur

Matrix

Matrix E1X Manuel utilisateur

Matrix

Matrix PERFORMANCE CLIMBMILL Manuel utilisateur

Matrix

Matrix Elliptical total body Manuel utilisateur

Matrix

Matrix MD-S70 Manuel utilisateur

Matrix

Matrix G7-S34-02 Manuel utilisateur

Matrix

Matrix LATERAL RAISE STRENGTH G3S21 02 Manuel utilisateur

Matrix

Matrix E5X-04 Manuel utilisateur

Matrix

Matrix E7XE-03 Manuel utilisateur

Matrix

Matrix G7-S12 Manuel utilisateur

Matrix

Matrix A7X-04 Manuel utilisateur

Matrix

Matrix G7-S77-02 Manuel utilisateur

Matrix

Matrix A5x-02 Manuel utilisateur

Matrix

Matrix G7-S74-02 Manuel utilisateur

Matrix

Matrix E1X Manuel utilisateur

Matrix

Matrix MX-A5x Manuel utilisateur

Manuels vélo elliptique populaires d'autres marques

Weslo

Weslo Momentum 4.0 Elliptical Manuel d'utilisation et d'entretien

Progear Fitness

Progear Fitness Air elliptical pro 1307 Manuel utilisateur

Torque Fitness

Torque Fitness XPLLP Manuel utilisateur

Octane Fitness

Octane Fitness PRO3700C Manuel utilisateur

Xterra

Xterra FS5.8e Manuel utilisateur

Bodyguard

Bodyguard E-40 Manuel utilisateur

Bonn Germany

Bonn Germany Concept 2.2 Manuel utilisateur

Precor

Precor Resolute RSL 620 Manuel utilisateur

NordicTrack

NordicTrack E 9.2 Elliptical Manuel utilisateur

Vision Fitness

Vision Fitness X6600iNetTV Manuel utilisateur

SportsArt Fitness

SportsArt Fitness ECO-NATURAL Elite E874 Manuel utilisateur

Sears

Sears FREE SPIRIT C249 30737 0 Manuel utilisateur

True

True FS-64 Manuel utilisateur

Sport-thieme

Sport-thieme ST 310 Manuel utilisateur

VIRTUFIT

VIRTUFIT CTR 1.1 Manuel utilisateur

Kettler

Kettler GIRO C 1 Manuel utilisateur

CIRCLE FITNESS

CIRCLE FITNESS E7 Manuel utilisateur

Reebok

Reebok 1000 Zx Elliptical Manuel utilisateur