Matrix Telecom SPARSH VP210 Manuel utilisateur
Thank you for choosing SPARSH VP210! Please read this guide first for
correct installation and retain it for future reference. The information in this
guide was current at the time of publication. All specifications are subject to
change without notice.
This Guide is meant to help you install and connect the phone to make and
receive calls. For detailed installation instructions, refer to the System Manual.
Copyright
All rights reserved. No part of this document may be copied or reproduced
in any form or by any means without the prior written consent of Matrix
Comsec Pvt. Ltd.
Warranty
Limited Warranty. Valid only if primary protection is provided, mains supply is
within limit and protected, and environment conditions maintained within
product specifications. Complete warranty statement is available on our
website: www.MatrixTeleSol.com
Know Your SPARSH VP210
SELECT A LOCATION
Step 1
Ÿ SPARSH VP210 Phone
Ÿ Handset with handset cord
Ÿ Ethernet Cable
Ÿ Stand
What Your Package Contains
Installing SPARSH VP210
While talking, Press to increase and press to decrease
Speech volume.
When the phone rings, Press to increase and press to
decrease Ringer volume.
Volume Keys
1. LCD Screen
2. Ringer LED
3. Navigation Key/SIP Line Key
4. Context Sensitive Key
5. Dial Pad
6. Volume Increase Key
7. Volume Decrease Key
8. Speaker Key
9. Mute
10. Headset Key
11. Handset
1
2
3
4
4ghi 5jkl 6mno
7pqrs 8tuv 9wxyz
*#
0
2abc 3def
1
5
6
7
11 98
10
Mount SPARSH VP210 on the Desk
Stand
Page 1
Image A
ŸStand Attached at 45 Degree angle.
Attach the Stand
Ÿ You can attach the Stand in the following ways - at an angle
of 45 degrees and 55 degrees as shown in Image A and
Image B.
MATRIX COMSEC
Head Office
394-GIDC, Makarpura, Vadodara - 390010, India
Ph:+91 85111 73344
E-mail: Customer[email protected]
www.MatrixTeleSol.com
Version 1. September 2020.
Connect the Handset
Ÿ Connect the handset of the SPARSH VP210 to the phone body
using the Spring Cord (supplied with the phone).
Ÿ Connect the long straightened end of the Spring Cord into the
RJ9 connector at the bottom of the phone, marked with the
symbol .
DSS532
Headset
Image B
Adapter
Computer
Headset
Handset
Router /
Switch
Adapter
Computer
Headset
Router /
Switch
Page 2
ŸStand Attached at 55 Degree angle.
CONNECT
Step 2
10.98"
3.66"
3.66"
STARTUP AND OPERATE
Step 3
Connect the Headset (not supplied by Matrix)
Ÿ You may plug in a headset with RJ9 connector into the
headset port at the bottom of the phone, marked with the
symbol .
Connect to the IP Network
Ÿ Connect the LAN Port of the phone to the IP Network —
A Router or LAN Switch — using the Ethernet Cable.
Connect a PC to the Phone
Ÿ Plug in the Ethernet Cable into the PC Port of the
phone and the other end into the LAN Port of your PC/LAN
Switch.
Connect the Power Supply
Ÿ It is a PoE enabled phone and can be powered over Ethernet
by connecting it to a PoE enabled LAN Switch (IEEE 802.3af
Compliant).
Ÿ If you do not want to use PoE, plug in the connector of the
Adapter into the power jack (DC Jack) at the bottom
of the phone.
Plug in the Power Adapter into a power outlet.
Note:
Ÿ If both the power options, that is, PoE as well as Power
Adapter are available to the phone, then the phone will derive
power from the PoE enabled LAN Switch.
Ÿ The IP phone should be used with Matrix original power
adapter (5V/0.6A) only. The use of any third-party power
adapter may cause damage to the phone.
Ÿ When the IP Phone is connected to the network and supplied
with power, the booting process initiates.
Ÿ After loading the application, the phone obtains the Network
Settings, updates the Firmware (if required), obtains the
configuration and then attempts to register. To register and
configure the phone as a SIP Extension, refer to the System
Manual. For operating instructions, refer to the SPARSH
VP210 User Guide.
The documentation can be found at
http://www.matrixtelesol.com/product-manuals.html
Version Supported
Ÿ The SPARSH VP210 is supported with below firmware
versions of PRASAR, ANANT and SARVAM UCS.
PRASAR UCS: 2.4.0 and Onwards
ANANT UCS: 2.1.0 and Onwards
SARVAM UCS: ENT / SME / SOHO: V01R06.05.00 and Onwards
SMB: V01R06.06.00 and Onwards
Attach the Foot Stand
Ÿ You can attach the Stand in the following ways - at an angle
of 45 degrees and 55 degrees as shown in Image A and
Image B.
Autres manuels Matrix Telecom Système d'interphone
