Matrix Fitness MX-E5xc Manuel utilisateur

MX-E5xc SERVICE

MANUAL

TABLE OF CONTENTS

SECTION 1: MAINTENANCE PROCEDURE…………….…...3

1. Preventive maintenance schedule……………………..……..…..4

2. Cleaning the grooves………………………………………..........5

SECTION 2: WIRING DIAGRAM INSTRUCTION…...........…6

1. MX-E5xc wiring diagram instruction…………………………….7

2. Console cable wiring diagram ………………….………………..8

3. Pulse sensor wire wiring diagram…………………..……...….….8

SECTION 3: CONSOLE ENGINEERING MODE GUIDE…….9

1. How to enter into the engineering mode?...................................10-11

SECTION 4: TROUBLESHLOOTING…………………………..12

1. No display on the console or the display is dim……………….14

2. No RPM is displayed during the exercise……………………...15

3. All or some of the function keys do not respond…………...….16

4. No resistance change or too hard for pedaling…………………17

5. Feel slipping while pedaling……………………………………18

6. Knocking or creaking noises……………………………………18

7. Heart-Rate-Control function does not work…………………….19

SECTION 5: SOFTWARE UPGRADE PROCEDURE…………..20

1. MX-U5x bike software upgrade SOP….......................................21-22

SECTION 1

MAINTENANCE PROCEDURE

LubricateAir Shock

InspectCleanV Belt

InspectBelt Grooves

Inspect

Handrail &

Handlebar

InspectCleanHandlebar

InspectCleanDisplay Console

InspectCleanFrame

Inspect

Console Mounting

Bolts

AnnualBiannualQuarterlyMonthlyWeeklyDailyItem

VISION BIKE

PREVENTIVE MAINTENANCE SCHEDULE

Caution:

If there is any dust in the grooves of the Poly-V belts and pulleys, noises

will be generated during operation.

Frequency: Every 3 to 4 months.

CLEANING THE GROOVES

Procedure:

1.Remove the Poly-V belts and check

the grooves of the belt for dirt or dust

and clean it if any.

2.Check the grooves in the pulley for

dirt or dust and clean it if any.

3.Check the grooves in the roller pulley

for dirt or dust and clean it if any

SECTION 2

WIRING DIAGRAM INSTRUCTION

MX-E5xc WIRING DIAGRAM INSTRUCTION

P01 : Console cable

P03 : Pulse sensor wire

SECTION 3

CONSOLE ENGINEERING MODE GUIDE

How to enter into the engineering mode?

1. Press & Hold both “DOWN” and “UP”

at the same time for 3-5 sec. Then, the

dot vision display will show

“MANAGER”

2. Press the " UP or DOWN" to select you

want and press the “SELECT" key enter.

To Store up the parameterSTART

Clean accumulate time and distanceHold MANUAL & RANDOM for 3’S

Enter addressSELECT

Select address or decrease parameterDOWN

Select address or add parameterUP

functionkey name

Engineer mode interpret

Test for factoryENG 1

HR testSERVICE 4

Show accumulate distance & timeSERVICE 3

HW test mode show RPMSERVICE 2

Display testSERVICE 1

Select address or add parameterMANAGER

Function interpretDisplay show

Table des matières

Autres manuels Matrix Fitness vélo elliptique

Matrix Fitness

Matrix Fitness AURA Series Manuel utilisateur

Manuels vélo elliptique populaires d'autres marques

Weslo

Weslo Momentum 4.0 Elliptical Manuel d'utilisation et d'entretien

Progear Fitness

Progear Fitness Air elliptical pro 1307 Manuel utilisateur

Torque Fitness

Torque Fitness XPLLP Manuel utilisateur

Octane Fitness

Octane Fitness PRO3700C Manuel utilisateur

Xterra

Xterra FS5.8e Manuel utilisateur

Bodyguard

Bodyguard E-40 Manuel utilisateur

Bonn Germany

Bonn Germany Concept 2.2 Manuel utilisateur

Precor

Precor Resolute RSL 620 Manuel utilisateur

NordicTrack

NordicTrack E 9.2 Elliptical Manuel utilisateur

Vision Fitness

Vision Fitness X6600iNetTV Manuel utilisateur

Matrix

Matrix MX-A5x Manuel utilisateur

SportsArt Fitness

SportsArt Fitness ECO-NATURAL Elite E874 Manuel utilisateur

Sears

Sears FREE SPIRIT C249 30737 0 Manuel utilisateur

True

True FS-64 Manuel utilisateur

Sport-thieme

Sport-thieme ST 310 Manuel utilisateur

VIRTUFIT

VIRTUFIT CTR 1.1 Manuel utilisateur

Kettler

Kettler GIRO C 1 Manuel utilisateur

CIRCLE FITNESS

CIRCLE FITNESS E7 Manuel utilisateur