Masterlock BCO0103 Mode d’emploi

Instructions for installation of knob or lever locksets

Backset is the distance from the door edge to the center of the hole on the door face. Master Lock door locks are supplied

with an adjustable latch which can fit 2-3/8” (60mm) or 2-3/4” (70mm) backset.

Follow steps below to change backset.

To convert to 2-3/4" backset

Backset

a. This latch is for 2-3/8" (60mm) backset.

b.Keep spindle cam in correct position as illustrated. Pull spindle cam all the way to the right.

c. Your latch is now set for 2-3/4" (70mm) backset.To reset 2-3/8" backset,push spindle all the way back to the left.

Mark door with template Drill holes

Measure one half of door thickness from doorstop

and mark for the vertical centerline of strike. Drill

1" hole, 1/2" deep at the intersection of the

horizontal and vertical centerlines.

Close door to mark horizontal

centerline of strike.

Insert latch in

hole, mark

outline of face

plate and

chisel 11/64"

(4mm) deep.

Insert latch and tighten screws.

Select 2-3/8" or 2-3/4" (60mm or 70mm)

backset as desired and mark center of hole

on door face.

Drill 2-1/8" (54mm) hole on door face from both sides

to avoid wood splitting. Drill 1" (25.4mm) hole for latch.

Install latch

Attach the latch face that matches the mortise in the edge of your door

Fin

Floating Sleeve

Round Face Plate

Locate floating sleeve and round

face plate and proceed.

To change latch faces:

1. Use a flat screwdriver to separate the face plate.

2. Snap selected latch face onto backplate.

For drive in installation:

Push latchbolt to the end and hold. Align the round face

plate opening with the fin on the latch. Push to the end

and rotate the round face plate counter-clockwise. After

assembly, release latchbolt to fully extend. Move the

floating sleeve toward the round face plate until the

edge fits into the ring opening of the round face plate.

Back Plate

Face Plate

Install outside knob (or lever)

Insert spindle through latch. Press flush against door. (NOTE: Key hole must be in down position).

Install inside knob (or lever)

Install inside knob (or lever) and tighten screws until lock is firm.

a. Match screw holes on strike with vertical centerlines on jamb. Mark outline of strike plate and chisel out until strike

is flush with jamb. (Approx. 1/8")

b.Install strike and tighten screws.

Install strike

1-3/4"

45mm 1-9/16"

40mm 1-3/8"

35mm

Make 1" Hole at Center of Door Edge

TEMPLATE

Fold on Dotted Line and Fit on Door Edge

For Backset 2-3/8"

For Backset 2-3/4"

Check out the collection of home doors & windows we offer.

Ce manuel convient aux modèles suivants

Autres manuels Masterlock Verrouillage

Masterlock

Masterlock 4696D Manuel utilisateur

Masterlock

Masterlock 5440D Manuel utilisateur

Masterlock

Masterlock P005CML Manuel utilisateur

Masterlock

Masterlock Speed Dial 1500iD Guide d'installation

Masterlock

Masterlock 3685 Manuel utilisateur

Masterlock

Masterlock 4697DWD Manuel utilisateur

Masterlock

Masterlock 5400D Manuel utilisateur

Masterlock

Masterlock 3681 Manuel d'installation

Masterlock

Masterlock 4697 Manuel utilisateur

Masterlock

Masterlock 5424EURD Manuel utilisateur

Masterlock

Masterlock Pushkey 2650EURD Manuel utilisateur

Masterlock

Masterlock 1630 Manuel utilisateur

Masterlock

Masterlock 651EURD Manuel utilisateur

Masterlock

Masterlock master lock Manuel utilisateur

Masterlock

Masterlock Select Access 5412EURD Manuel utilisateur

Masterlock

Masterlock Select Access 5420EURD Manuel utilisateur

Masterlock

Masterlock SAFESPACE 5423D Manuel utilisateur

Masterlock

Masterlock 5441EURENT Manuel utilisateur

Masterlock

Masterlock 4697D Manuel utilisateur

Masterlock

Masterlock 1630 Manuel de service

Masterlock

Masterlock 4400EURENT Manuel utilisateur

Masterlock

Masterlock Select Access 5426EURD Manuel utilisateur

Masterlock

Masterlock 4400 Manuel utilisateur

Masterlock

Masterlock 4400 Manuel utilisateur

Manuels Verrouillage populaires d'autres marques

Magic

Magic 105 Manuel utilisateur

Gantner

Gantner GAT NET.Lock 7020 System Guide rapide

Wittkopp

Wittkopp Insys 7202 Manuel utilisateur

Dorma

Dorma Studio Classic Manuel utilisateur

Securam

Securam ECSL-601 Manuel utilisateur

Sudhaus

Sudhaus 3003 Manuel utilisateur

Safety 1st

Safety 1st 48517 Manuel utilisateur

Pado

Pado FDS-10 Manuel utilisateur

Esco

Esco systeQ Series Manuel utilisateur

COMPX

COMPX National D8951 Manuel utilisateur

secureo

secureo Key Box Manuel utilisateur

Stock Loks

Stock Loks C8713 Manuel utilisateur

COMPX

COMPX 1T-058 Manuel du propriétaire

Auslock

Auslock T11 Manuel utilisateur

ELCOM

ELCOM 7205 Manuel utilisateur

Stealth SAFES

Stealth SAFES ShadowVault Manuel utilisateur

Knox

Knox KeySecure 5 Manuel utilisateur

Kwikset

Kwikset 48334/01 Manuel utilisateur