Marzocchi MXC+ECC Air Manuel utilisateur
MXC
+
ECC
Air
INSTRUCTIONS
GENERAL RULES
1. Where specified, assemble and disas-
semble the shock absorption system us-
ing the M
ARZOCCHI
special tools only.
2. On reassembling the suspension system,
always use new seals.
3. Clean all metal parts with a special,
preferably biodegradable solvent, such
as trichloroethane or trichloroethylene.
4. Before reassembling, lubricate all parts
in contact with each other using silicone
fat spray or a specific oil for seals.
5. Always grease the lip seal rings before
reassembling.
6. Use wrenches with metric size only.
Wrenches with inch size might damage
the fastening devices even when their
size is similar to that of the wrenches in
metric size.
MXC
+
ECC
Air
FAILURES, CAUSES AND REMEDIES
This paragraph reports some failures that may occur when using the fork. It also indicates possible causes and suggests a remedy. Always
refer to this table before doing any repair work.
FAILURES CAUSES REMEDIES
Adjuster position does not affect fork
operation
1. Dirt inside legs
2. Pumping element of r.h. leg does not
work properly.
1. Clean carefully and change oil
2. Replace pumping element.
Oil leaking through the bottom of slider O-ring on the pumping rod or on cartridge
securing nut bottom damaged
Replace the O-ring
Oil leaking through the top of the slider 1. Oil seal is worn out
2. Stanchion tube is scored
3. Excessive dirt on slider oil seal
1. Replace oil seal
2. Replace crown/stanchions assembly, oil
seals and dust seals
3. Clean the oil seal seat and replace oil seal
Fork has not been used for some time and
is locked out
Oil seals and dust seals tend to stick to
stanchions
Raise dust seal and lubricate stanchion
tube, dust seal and oil seal
Pressure drop Cap valve damaged Replace cap and/or valve
Excessive play of stanchions in the sliders Pilot bushings worn out Replace bushings
Fork rebounds too fast in any adjuster
position
Dirt inside fork legs Clean carefully and change oil
Fork does not react to rebound lock LH fork cartridge faulty Replace hydraulic cartridge
MXC
+
ECC
Air
RECOMMENDATIONS FOR
MAINTENANCE
M
ARZOCCHI
forks are based on advanced
technology, supported by year-long experi-
ence in the field of professional mountain
biking. In order to achieve best results, we
recommend to check and clean the area
below the dust seal and the stanchion tube
after each use and lubricate with silicone
oil.
In general, M
ARZOCCHI
forks can offer top
performance from the start. However, in
some cases a short running-in period is
required (5-10 hours) for inner adjustments.
This running-in period will make fork life
longer and ensure fork top performance
over time.
IMPORTANT: change oil at least every
100 working hours and check pressure at
least every 10 working hours.
Polished forks should be cleaned with
bodywork polish at regular intervals in
order to preserve their original finish.
INSTALLATION
Installing the fork on a bicycle is a very
delicate operation that should be carried
out with extreme care. The installation should
always be checked by one of our Technical
Service Centers.
WARNING: Steer tube/headset
mounting and adjustment must be
carried out in compliance with the headset
manufacturer’s instructions. Improper in-
stallation may jeopardize the safety of the
rider.
To replace it, contact one of our Technical
Service Centers with the required tools.
WARNING: In case of improper
installation of the steer tube into the
crown, the rider might lose control of his/
her bicycle, thus jeopardizing his/her safety.
DISC BRAKE SYSTEM ASSEMBLY
If a disc brake system is installed, brake
supports fixing pins can be replaced with
screws (part no. 532979QF) available as
spare parts.
Tighten the above screws to 10 Nm.
Assembling the brake caliper onto the slider
is a very delicate operation that should be
carried out with extreme care.
Improper assembly might overstress the
caliper supports which might break.
When installing the disc brake system, be
sure to properly follow the instructions given
by the manufacturer.
MXC
+
ECC
Air
D
D
D1
2
CC
4
LOCK
ADJUSTMENTS
FORK LEG PRESSURIZATION
Blow pressurized air through the valves to set
COMPRESSION damping. To change the
pressure inside the fork legs, remove the
protection cap (2) and depressurize each
leg by pushing lightly on valve pin with a bit.
Fully tighten adapter fitting (D), supplied
with the fork, on M
ARZOCCHI
pump (C).
Screw fitting end –with O-ring (D1) on
valve, and pressurize until the required value
is reached. Unscrew the fitting/pump as-
sembly and refit the cap (2).
IMPORTANT: inflate using special
M
ARZOCCHI
pump with pressure gauge.
Use of improper tools or other procedures
than specified ones might lead to improper
inflating.
NOTE: in case of air leakages when adapter
fitting (D) is fitted, ensure that the O-ring
(D1) is not damaged.
REBOUND LIMITER
(only left leg)
In case of hard uphill path, fork leg rebound
can be locked for improved behavior.
Position the knob (4) on l.h. fork leg top to
“LOCK” to lock rebound limit in this posi-
tion; this also allows to decrease fork leg
height for optimal attitude uphill, thus sup-
porting suspension compression operation.
Reposition the knob to its original position
so that the fork will rebound and restart to
work as before.
WARNING: do not position to
“LOCK” when riding downhill as
available travel might not be enough, thus
jeopardizing rider’s safety
MXC
+
ECC
Air
E
32
REBOUND ADJUSTMENT VIA
INNER PUMPING ROD
The adjuster controlling REBOUND damp-
ing adjustment is accommodated inside
the pumping element (32) inside the r.h.
fork leg.
To access the adjuster, unscrew the top cap
(8) and push the stanchions fully down (see
section DISASSEMBLY Fig. 2).
Fit the supplied hexagon rod (E) into the
stanchion tube and into the adjuster inner
hole. Rotate the adjuster clockwise for harder
damping, counterclockwise to soften it.
Refit the cap (8) and tighten it to the
specified torque (see section REASSEMBLY,
Fig. 29).
MXC
+
ECC
Air
▲
▲
▲
▲
▲
▲
▲
▲
▲
▲
▲
▲
▲
DISASSEMBLY
GENERAL
– The reference numbers given in this section relate to the components shown in the fork exploded view.
– Before starting any operation. please read the diagram below. It shows the quickest procedure and the exact disassembling sequence.
Locate the part you need to remove in the diagram, then look at the arrows to determine which other parts you need to remove first.
DISASSEMBLY DIAGRAM
▲
▲
FOOT NUT FIG. 5
SEAL ASSEMBLY AND
PILOT BUSHING CHANGE
CROWN AND STANCHIONS
ASSEMBLY FIG. 7
STOP RING FIG. 9
OIL SEAL FIG. 10
UPPER WASHER FIG. 11
PILOT BUSHING FIG. 12
HYDRAULIC CARTRIDGE, REBOUND
SPRING AND WASHER FIG. 6
HYDRAULIC CARTRIDGE CHANGE
(l.h. fork leg)
FORK OIL CHANGE
STANCHION TUBE CAP FIG. 1/2/3
AIR VALVE CHANGE
FIG. 15
REPLACING PUMPING ELEMENT
(r.h. fork leg)
REPLACING VALVE ASSEMBLY
REBOUND BUMPER,
PUMPING ROD,
REBOUND SPRING FIG. 13
STOP RING, VALVE ASSEMBLY
FIG. 14
DUST SEAL FIG. 8
MXC
+
ECC
Air
4
3
6
34
11
8
5
STANCHION TUBE CAP
FIG. 1 (only left leg)
Loosen screw (3) and remove rebound
limiting knob (4).
FIG. 2
Depressurize each fork leg (see section
ADJUSTMENT).
Unscrew the caps (8) and (6) with a 21 mm
socket wrench.
Remove the caps complete with O-ring (5)
from the stanchion tubes.
FIG. 3 (only left leg)
Lock the check nut (34) and remove the cap
(6) from hydraulic cartridge end (11).
MXC
+
ECC
Air
118
20
19
11
9
FIG. 4
Push the stanchions (1) into the sliders (18)
and let all the oil drain out from the fork legs.
Pump the stanchions several times to help
oil drain off.
WARNING: Remember to always
recycle any used oil.
To change the fork leg oil follow the proce-
dure as described in section “REASSEMBLY”
from Fig. 27 to Fig. 30.
HYDRAULIC CARTRIDGE CHANGE
AND PUMPING ROD CHANGE
FIG. 5
Turn the fork leg upside-down and unscrew
the foot nuts (20) by the use of a 15 mm
socket wrench complete with O-Rings (19).
FIG. 6 (only left leg)
Remove the hydraulic cartridge (11) com-
plete with rebound spring (9) and foot
washer (23, see exploded view) from the
l.h. stanchion.
Replace the whole hydraulic cartridge.
MXC
+
ECC
Air
1
18
13 14
SEAL ASSEMBLY AND PILOT
BUSHING CHANGE
FIG. 7
Withdraw the crown and stanchions as-
sembly (1) from the sliders (18).
FIG. 8
Remove the dust seal (13) from the top of
the sliders using a small screwdriver.
FIG. 9
Remove the stop ring (14) from the sliders
by placing the screwdriver bit in one of the
three openings on the stop ring.
IMPORTANT: when removing the stop
ring, make sure not to damage its seat.
MXC
+
ECC
Air
15
A
16
17
FIG. 10
Fit the slider protector (A) onto the slider
and remove the oil seal (15) with the help
of a large screwdriver.
IMPORTANT: when removing the oil seal,
make sure not to damage its seat. Once
removed the oil seals should not be used
again.
FIG. 11
Remove the upper washer (16) from the
slider.
FIG. 12
Fit the bit of a small screwdriver into upper
edge slot of the pilot bushing (17) and lift
gently. Pull the bushing out of the slider and
make all necessary changes.
Table des matières
Autres manuels Marzocchi Accessoires pour vélos
Marzocchi
Marzocchi SHIVER Guide de l'utilisateur
Marzocchi
Marzocchi MAX COMP + ETA - 105 Manuel utilisateur
Marzocchi
Marzocchi SHIVER DC Manuel utilisateur
Marzocchi
Marzocchi Bomber 58 Guide de démarrage rapide
Marzocchi
Marzocchi Bomber 2004 Manuel utilisateur
Marzocchi
Marzocchi Dirt Jam Comp 2005 Manuel du propriétaire
Marzocchi
Marzocchi Z3 QR20 Manuel utilisateur
Marzocchi
Marzocchi Bomber Z1 BAM Manuel utilisateur
Marzocchi
Marzocchi Bomber 2002 Manuel utilisateur
Marzocchi
Marzocchi Marathon XC 2005 Manuel du propriétaire
Marzocchi
Marzocchi Z1 QR20 Manuel utilisateur
Marzocchi
Marzocchi Dirt Jumper 1,5 QR20 Manuel utilisateur
Marzocchi
Marzocchi Bomber 2002 Manuel utilisateur
Marzocchi
Marzocchi Z1 Alloy 1999 Manuel utilisateur
Marzocchi
Marzocchi QR20 Plus Manuel utilisateur
Marzocchi
Marzocchi EXR Coil Manuel utilisateur
Marzocchi
Marzocchi Monster T Manuel utilisateur
Marzocchi
Marzocchi Shiver SC 2005 Manuel du propriétaire
Marzocchi
Marzocchi Z2 Atom Race Manuel utilisateur
Marzocchi
Marzocchi Z3 QR20 Manuel utilisateur
