Martin Mania DC2 Manuel utilisateur

Mania DC2

user manual

Measurements are expressed in millimeters.

312

142

290

250

Ø13

without permission in writing from Martin Professional A/S, Denmark.

Printed in China.

P/N 35000138, Rev. B.

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Safety information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Mania DC2 overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

AC power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Overhead mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Changing effect orientation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Focusing the Mania DC2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Basic service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Lamp maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Mains fuse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

4 Mania DC2 user manual

NTRODUCTION

Thank you for selecting a Martin Mania DC2. The Mania DC2 is a

luminaire that projects a 53° beam rising-flames effect at user-selectable

speed.

SAFETY INFORMATION

Warning! This product is not for household use. It presents risks of

lethal or severe injury due to fire and heat, electric shock, and

falls.

Read this manual before powering or installing the fixture, follow the safety

precautions listed below and observe all warnings in this manual and

printed on the fixture. If you have questions about how to operate the

fixture safely, please contact a Martin distributor for assistance. Refer any

service operation not described in this manual to a qualified technician. Do

not modify the fixture or install other than genuine Martin accessories and

upgrade kits.

Refer servicing to qualified personnel.

Maximum ambient temperature Ta= 40°C(104°F).

See serial label for replacement fuse size and lamp type.

Suitable for mounting on normally flammable surfaces.

Do not look directly into the light.

Risk of fire, electrical shock and burns.

Use only in dry locations.

For indoors use only.

Do NOT block exhaust vents.

Shields, lenses or ultraviolet screens shall be changed if they become

visibly damaged to the extent that their effectiveness is impaired, for

example, by cracks or deep scratches.

Introduction 5

The lamp shall be changed if it becomes damaged or thermally deformed.

If the external power cord of this luminaire is damaged, it shall be

replaced by a special cord exclusively available from your Martin dealer.

Avoiding electric shocks

Warning Always disconnect from mains power before replacing the

lamp, fuses, or any part, and when not in use.

• Before operation ensure that factory setting of voltage and frequency

match local power supply.

• Always ground (earth) the fixture electrically.

• Use only a source of AC power that complies with local building and

electrical codes and has both overload and ground-fault protection.

• Do not expose the fixture to rain or moisture.

• Never operate the fixture with missing or damaged lenses and/or covers.

Protecting yourself and others from burns and fire

Warning Hot lamp. The exterior of the fixture can become hot. Allow to

cool for at least 5 minutes before handling or opening.

• Surface temperature under steady state condition = 60°C (140° F).

• Minimum distance to flammable material = 0.3 m (1 ft).

• Minimum distance to illuminated surface 1.0 m (3.3 ft).

• Never attempt to bypass the thermostatic switch or fuses. Always replace

defective fuses with ones of the specified type and rating.

• Ensure that the air flow through vents is free and unobstructed.

• Provide a minimum clearance of 0.1 meters (4 inches) around fans and

air vents.

• Never place filters or other materials over the lens or in the optical path.

• The exterior of the fixture can become hot. Allow the fixture to cool for at

least 5 minutes before handling.

• Do not block the fan or vent.

• Do not operate the fixture if the ambient temperature (Ta) exceeds 40° C

(104° F).

• Do not stare directly into the light.

• Never operate the fixture without all lenses and covers installed: an

unshielded lamp emits dangerous UV radiation that can cause burns and

eye damage.

6 Mania DC2 user manual

Preventing injuries due to falls

• When suspending the fixture above ground level, verify that the structure

can hold at least 10 times the weight of all installed devices.

• Verify that all external covers and rigging hardware are securely fastened

and use an approved means of secondary attachment such as a safety

cable.

• Block access below the work area whenever installing or removing the

fixture.

UNPACKING

The packing material is carefully designed to protect the fixture during

shipment - always use it to transport the fixture.

The Mania DC2 comes with the following:

• 3-wire IEC power cable

• User manual

MANIA DC2 OVERVIEW

Effect speed

Fuse holder

Thumb screw (cover lock)

Power on switch

Swivel locks

Mounting bracket

AC supply setting

Effect direction

Mains socket

(rotation direction)

Cooling fan

Safety cable attachment

(rotation speed)

Installation 7

NSTALLATION

AC POWER

Before operation ensure that factory setting of voltage and frequency

match local power supply.

Always ground (earth) the fixture electrically.

Use only a source of AC power that complies with local building and

electrical codes and has both overload and ground-fault protection.

Note: If the external power cord of this luminaire is damaged, it

shall be replaced by a special cord exclusively available from

your Martin dealer.

Configuring for local mains power

The Mania DC2 has a switch-selectable power supply that can operate in

the following voltage ranges at 50-60 Hz:

• 115 - 120 volts (setting 115)

• 220 - 240 volts (setting 230)

Warning Do not operate the fixture on a power supply that falls outside

of these ranges.

Select the operating range using the AC supply switch at the rear of the

fixture.

AC supply setting

8 Mania DC2 user manual

Installing a plug on the mains lead

Warning! For protection from dangerous electric shock, the fixture must

be grounded (earthed). The AC mains supply shall have

overload and ground-fault protection.

Important! Verify that the feed cables are undamaged and rated for the

current requirements of all connected devices before use.

The fixture’s mains lead may require a grounding-type cord cap that fits

your power distribution cable or outlet. Consult a qualified electrician if you

have any doubts about proper installation.

Following the cord cap manufacturer’s instructions, connect the

appropriate wires to ground (earth), live, and neutral. The following table

below shows some common wire identification schemes.

Applying power

1 Connect the mains power cable to the fixture at the 3-prong IEC male

input socket on top of the fixture.

2 Turn the power on using the power-on switch.

Function Wire (EU) Wire (US)

live brown black

neutral blue white

ground yellow/green green

Mains socket

Power on switch

Installation 9

OVERHEAD MOUNTING

The Mania DC2 can be hung overhead with a clamp (not included).

Warning! Block access below the work area before proceeding.

Always use a secure means of secondary attachment.

For indoors use only.

To hang the Mania DC2 on an overhead support:

1 Verify that the structure can support at least 10 times the weight of all

installed fixtures, clamps, cables, auxiliary equipment, and other items.

2 If hanging the fixture with a rigging clamp, verify that the clamp is

undamaged and is designed for the fixture’s weight. Bolt the clamp

securely to the mounting bracket on the fixture with a grade 8.8

(minimum) M12 bolt and lock nut, or as recommended by the clamp

manufacturer, through the clamp hole in the mounting bracket.

3 If permanently installing the fixture, verify that the hardware (not included)

and mounting surface can bear at least 10 times the fixture’s weight.

4 Working from a stable platform, clamp or fasten the fixture to the

structure.

5 Install a safety cable that can hold at least 10 times the weight of the

fixture through the safety cable attachment point on the fixture.

6 Loosen the swivel locks, tilt the fixture to the desired angle, and retighten.

Swivel locks

attachment point

Safety cable

10 Mania DC2 user manual

7 Verify that the fixture is at least 1 meters (3.3 ft.) from the surface to be

illuminated and at least 0.3 meters (1 ft.) from any combustible materials.

Verify that the clearance around the air vents is at least 0.1 meters (4 in.).

CHANGING EFFECT ORIENTATION

When installing the fixture in a location where the mounting bracket is

underneath the fixture you need to change the orientation of a color filter

and a gobo inside the product to ensure that the image that is projected is

not upside down.:

1 Ensure that the fixture is disconnect from power and has been allowed it

to cool for 5 minutes.

2 Remove the thumb screw holding the cover in place.

Thumb screw

Table des matières

Autres manuels Martin Projecteur

Martin

Martin Exterior 200 Manuel utilisateur

Martin

Martin PAR 2 RGBW Zoom Manuel utilisateur

Martin

Martin Lynx Manuel utilisateur

Martin

Martin Rush SM 650 Manuel utilisateur

Martin

Martin MH 1 Profile Manuel utilisateur

Martin

Martin MAC 101 Series Manuel utilisateur

Martin

Martin MAC 2000 Wash XB Manuel utilisateur

Martin

Martin Exterior 600 Manuel utilisateur

Martin

Martin JEM ZR44 Hi-MASS Manuel utilisateur

Martin

Martin EFX500 Manuel utilisateur

Martin

Martin ATOMIC 3000 Manuel utilisateur

Martin

Martin Stage Cyclo Manuel utilisateur

Martin

Martin JEM Ready 365 Manuel utilisateur

Martin

Martin PAR 2 RGBW Zoom Manuel utilisateur

Martin

Martin MH 1 Profile Manuel utilisateur

Martin

Martin Juggler Manuel utilisateur

Martin

Martin Imager Series Manuel utilisateur

Martin

Martin MAC 250 Krypton Manuel utilisateur

Martin

Martin SynchroZap QX250 Manuel utilisateur

Martin

Martin Stagebar 2 Manuel utilisateur

Martin

Martin RoboZap Manuel utilisateur

Manuels Projecteur populaires d'autres marques

VIZULO

VIZULO Micro Martin Guide de l'utilisateur

EuroLite

EuroLite LED IP FL-100 SMD Manuel utilisateur

Cooper Wheelock

Cooper Wheelock XB12 Manuel utilisateur

Allen + Roth

Allen + Roth 17624-000 Manuel utilisateur

ADJ

ADJ 4 STAGE PAK Manuel utilisateur

Cooper Lighting

Cooper Lighting EGL91SW233 Manuel utilisateur

Max

Max 37496 Manuel utilisateur

BEGA

BEGA 85 143 Manuel utilisateur

Beamz

Beamz 151.226 Manuel utilisateur

EuroLite

EuroLite LED IP FL-8 Manuel utilisateur

Ledj

Ledj PERFORMER 36 RGB Manuel utilisateur

Perel

Perel ELS3 Manuel utilisateur

Perel

Perel ELS3WD Manuel utilisateur

LumX

LumX LM 36130 Manuel utilisateur

Xtricity

Xtricity 4-80053 Manuel utilisateur

Stahl

Stahl 6521/4 Series Manuel utilisateur

Ecosense

Ecosense EcoSpec Manuel utilisateur

Ayrton

Ayrton minipanel FX Manuel utilisateur