Martec MLXS524WS Manuel utilisateur

Protect yourself. Please read these instructions carefully prior to installstion and retain them for future reference. Failure to follow any of these instructions could void product warranties.

Sentinel InstaIIation Guide

Sentinel InstaIIation GuideSentinel InstaIIation Guide

MLXS524WS/ MLXS524MS

Turn off electrical power at fuse or circuit breaker box before wiring the Sentinel Security Light f ixture to the power supply.

Where other lights could shine on the sensoryou may contact Martec customer service.with the National AS/NZS Electrical CodeNear the outlet of a central heating unit or near an air conditioning unit

We strongly recommend that you read this manual carefully before installation. Installation MUST be carried out by a qualif ied and licensed electrician.When selecting your installation area its import to be awareof possible factors that could cause false triggering , such asdirect sunlight, window glare or refection, air condition units, swimming pool water ref lection, direct street lighting or large vegetation in the installation area.Although the Sentinel Security Light is weatherproof IP65 to prolong its lifespan it is sensible to install the unit in an area that is not directly exposed to extremeweather conditions.Determine the mounting location - a solid is preferable.

Install the f ixture on a height between 2 meters-3 meters above ground12 meters plusTo prolong the lifespan of the f ixture it is advised to install the unit in a selected area that is not directly exposed to extreme weather conditions and only mount on a wall under an eave or sof f it based on the recommended mounting height.The Sentinel Security Light features 3 f ixed independent motion sensor zones. Each sensor zone is 70°degrees and the total sensor coverage area is 210°degrees The detection distance per zone is 12 meters Install the motion sensor 2 meters-3 meters above the ground. Motion sensors are less sensitive when installed below 2 meters or above 3 meters.

Step 2. Connect the Sennel Security Light cables to the terminal blockEnsure the seal between the base cover bracket and the Sennel Security Light is properly seated and apply a sealant between the base cover bracket and the wall to guard against any water entry.than one the Sentinel Security Light on a single switch.Loosen the Sentinel Security Light mounting screws to remove the base cover bracket and seal. Feed the wall power cable through the back base cover bracket and through the Fixture Backplate Seal (C)before securely f ixing the wall plate and connecting the wires to the terminal block.Connect the Brown wire (live wire) from the AC power cord to the single Brown wire coming from the light f ixture on the terminalblock . Brown to Brown Connect the Blue wire from the AC power cord to the single Blue wire coming from the light f ixture on the terminal block.Blue to Blue

Press button SW4 and hold for 2 seconds - The LED will illuminate and rotate towards the direction of detection. After 3 minutes of walk test the Sentinel Security Light will reset to Night Time operation only. Should further walk test be required press SW4 again for 2 seconds.

On turning the power on the Sentinel Security Light will start a self-calibration program .During this process you will notice a f lashing green LED light rn the detector lens .Once the green light becomes stable and the Sentinel Security Light is ready for normal operation.

The Sennel Security Light is designed to be "plug and play" most installaons will require lile or no adjustment and can rely on the original default sengs :

Af ter the compleon of the installat ion switch the power back on

Press and release the SWI button to start sensitivity setting.The LEDs 1-4 above the buttons will indicate the setting selected・1 - High 12 meters. 2 - Medium 9 meters. 3 - Low 6 meters.Press and hold the SWI button for 2 seconds to conf irm and save the sensitivity choice.Night time mode setting - The f ixture has a built-in photocell that will automatically enable the f ixture functions at sunset and of f at dawn , therefore there is no need for a additional Lux setting function Motorized function to rotate the LED head towards motion detection within 3 sensor zonesSensor sensitivity set at high setting at a maximum distance of 12 meters

To prolong the original appearanee of the f ixture regularly clean the Sentinel Security Light with a soft damp cloth. Do not use paints, solvents, or other chemicals on this light f ixture. They could cause a premature deterioration of the outer body of the f ixture and will not be covered by the warranty.Important - Do not spray the Sentinel Security Light directly with a hose or power washer.

Remove the power to the Sentinel Security Light forabout 10 seconds then turn back on. The Sentinel Security Light will then go through its calibration warm up routine in preparation for normal operation.The Sentinel Security Light is set in NightMode.

1. Detection Method: Passive Infrared Sensor (PIR). PIR measures infrared light radiating from a person or object in its f ield of view.2. Sensor Range: up to 12 meters across a horizontaI detection zone of 210°degrees3. Power Source: 100 - 240V 50/60Hz4. Lumens : 17005. Weatherproof rating - IP656. Importa nt - No addition al lights should be connected to the Sentinel Security Light

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Martec Projecteur