Martec SCORPION DC Series Manuel utilisateur
www.martecaustralia.com.au
SCORPION DC Series Installation Guide
Thanks for choosing our SCORPION DC Series ceiling fan.
We strongly recommend that you read this manual carefully before installation.
Models Parameters (Fan Only):-
MSF133MR 1320mm 3 Blade Ceiling Fan Matt Black with remote control
MSF133WR 1320mm 3 Blade Ceiling Fan White Satin with remote control
MSF133BR 1320mm 3 Blade Ceiling Fan Brushed Nickel with remote control
Models Parameters (Fan and Light):-
MSF1333MR 1320mm 3 Blade Ceiling Fan Matt Black, 24W Tricolour LED Light with remote control
MSF1333WR 1320mm 3 Blade Ceiling Fan White Satin, 24W Tricolour LED Light with remote control
MSF1333BR 1320mm 3 Blade Ceiling Fan Brushed Nickel, 24W Tricolour LED Light with remote control
Part List:
Qty 1x motor assembly Qty 1x instruction manual Qty 1x screw kit Qty 3x blades
Qty 1x balancing kit Qty 1x hanging bracket Qty 1x remote control kit
Application
Flat Surface / Ceiling Corrugated Ceiling Apex Ceiling
Slope Ceiling up to 15°
How to Assemble
Secure the hanger bracket
to ceiling beam or a suitable
piece of timber inserted
between the ceiling beams
using the two long screws
supplied with the package.
(See Fg.1)
Place circular shockproof
gasket above the hanger
bracket. Align the bracket
and screw the hanger
bracket to the ceiling tightly.
(See Fg.2)
Place fan into hanger
bracket and align Ball Joint
Slot with hanger bracket as
illustrated.(See Fg.3)
After wiring is completed,
attach the canopy to the
hanger bracket by pushing
upwards and twisting anti-
clockwise. Tighten screws
and ensure canopy is not
touching the ball joint.
(See Fg.4)
Fg.1 Fg.2 Fg.3 Fg.4
Ball seat
rubber
cover
(packed
with
hanger
bracket)
Anti-vibration
washer
www.martecaustralia.com.au
WARNING Installation MUST carry out by a qualied and licensed electrician.
How to Install Blades
How to Install / Remove the Cover
Connect the 2-pin
connectors from motor
housing with the light kit
plate.
Install the light kit plate
to the motor using screw
provided.
Slot the metal cover into
the light kit. (See Fg.6)
CCT (Colour Changeable Temperature)
Fg.8
NB: Ensure the blades do not get damaged or bent during the
installation process while the fan maybe on the ground, this will aect
the performance and balance of the fan and this is NOT covered under
warranty.
Attach the blade to the top of the motor. Tighten and secure blade
with screws and washers provided. Repeat this procedure until all
blades are installed. (See Fg.5)
Fg.5
Choose colour temperature by icking the switch in the LED
(See Fg.7)
C = 5000K cool white
N = 4000K neutral white
W = 3000K warm white
Dimming
The SCORPION ceiling fan has a smart 3 step dimming LED light module which doesn’t require a dimmable remote control or a wall
dimmer. It only requires a remote control kit supplied with the product.
Turn the switch on and the light will turn on. Flick the switch on/o within 1 second and the light output will dim down to approx. 50%.
Flick the switch on/o again and the light output will dim down to approximately 15%. The light kit has NO memory function, it will turn
on at 100% initially.
Fg.6
Model shown with light Model shown fan only
Model shown fan only
Install the metal cover into
the light kit. (See Fg.7)
Fg.7
www.martecaustralia.com.au
WARNING Installation MUST carry out by a qualied and licensed electrician.
Instructions and Functions of Transmitter
1. LED indicator light
2. Light ON/OFF
(Use to dim light within 1s)
3. Speed of the fan
(1 high speed - 5 low speed)
4. Timing control of the fan
5. Direction of the fan (reverse
switch)
6. Fan ON/OFF
7. 12v battery to be used
in transmitter
NB: Remote shown fan and light NB: Remote shown fan only 1. LED indicator light
2. Speed of the fan
(1 high speed - 5 low speed)
3. Timing control of the fan
4. Fan On/OFF
5. Direction of the fan (reverse
switch)
6. 12v battery to be used in
transmitter
Installing Receiver Remote Control
Pairing Instructions
• Turn “ON” the power supply and within 30 seconds
• Press and hold the transmitters “FAN ON/OFF” button for 5 seconds and a “beep” will be heard
• Pairing initial step must be performed within 30 seconds of power being turned on
i) ensure the isolation switch or power supply to the rst installed fan is turned o prior to pairing futher fans
ie. pair one fan at a time
ii) ensure isolation switch is kept to the ON position, the isolation switch is not to be used as a light switch as
this will damage and make the remote recevier inoperable
Important Reminders
• Receiver must be correctly installed in the mounting bracket
• When the transmitter cannot control the receiver, please check
i) has sucient battery in the transmitter
ii) any existence of similar remote controlled products nearby that cause interference
• Replace battery if getting low as this will aect sensitivity of the transmitter
• Take the battery out from the transmitter when leaving used for a long time to avoid battery leaks
• Support up to 200W lighting power
• Isolation switch MUST be connected in the line
• Dimming switch on the light models is operated by tuning the light ON/OFF button within 1s. Light output will dim in
stages from 24W to 12W to 4W approximately
www.martecaustralia.com.au
WARNING Installation MUST carry out by a qualied and licensed electrician.
Wire Connections
CARE INSTRUCTIONS
• Ensure the ceiling fan is disconnected before any cleaning or maintenance work is carry out.
• LED lights are not detachable nor replaceable. It can only be supplied with the ceiling fan as one unit.
WARNING
• Installation of fans MUST follow SAA standards and meet local authority regulations.
• Installation MUST be carried out by a qualied and licensed electrician.
• Fan and light MUST be earthed.
• Bracket MUST be rmly attached to a at solid structure or timber frame.
• DO NOT mix blades from one model to another, all blades MUST be replaced if damaged.
• The warranty is VOID if product is not installed according to this installation guide.
6* Year Warranty
Visit our website for details https://www.martecaustralia.com.au/warranty-statement/
NB: Remote Control fan and light NB: Remote Control fan only
Ce manuel convient aux modèles suivants
6
Autres manuels Martec Ventilateur
Martec
Martec Flush Manuel utilisateur
Martec
Martec METRO DC Series Manuel utilisateur
Martec
Martec MMDC133WOR Manuel utilisateur
Martec
Martec VAMPIRE Series Manuel utilisateur
Martec
Martec Scorpion MSF133 Manuel utilisateur
Martec
Martec SATURN MXFSS20W Manuel utilisateur
Martec
Martec IMPERIAL SERIES Manuel utilisateur
Martec
Martec Elite AC Series Manuel utilisateur
Martec
Martec SATURN Series Manuel utilisateur
Martec
Martec Newport Series Manuel utilisateur
Martec
Martec Kingston MKDC124OB Manuel utilisateur
Martec
Martec DLS1043 Manuel utilisateur
Martec
Martec Lifestyle series Manuel utilisateur
Martec
Martec Albatross Mini Series Manuel utilisateur
Martec
Martec Ariel Series Manuel utilisateur
Martec
Martec Norfolk DC Smart Series Manuel utilisateur
Martec
Martec Lifestyle series Manuel utilisateur
Martec
Martec AVOCA DC Series Manuel utilisateur
Martec
Martec Malibu Series Manuel utilisateur
Martec
Martec DLS1045 Manuel utilisateur
