Marshall Amplification ML-702 Manuel utilisateur

Broadcast A/V Division

Dual 7” 3RU Rack Mount Monitor

ML-702

Operating Instructions

Table of Contents

1. Product Description........................................................................................ 3

2. Menu Settings ................................................................................................. 6

3. Speciﬁcations................................................................................................ 12

4. Included Accessories ................................................................................... 12

5. Troubleshooting ............................................................................................ 12

6. PCSet Remote Terminal Application........................................................... 13

7. WARRANTY .................................................................................................... 13

IMPORTANT SAFETY INSTRUCTIONS:

• Please read Operating Instructions (this manual) before using the product.

• Keep the manual for future reference.

• Read the cautions below to prevent possible component failure or degradation.

CAUTIONS:

• To avoid scratching the LCD surface, do NOT place the monitor on its face

• Avoid heavy impact.

• Do NOT use chemical solutions to clean this product. Simply wipe with a clean, soft cloth to

maintain the brightness of the surface.

• Do NOT block vent holes. Be aware of mounting heat-producing equipment below this product.

• Use the following Instructions and Trouble-shooting Section (page 12) of the manual to adjust

the product. Internal adjustments or repairs must be performed only by Marshall Electronics.

www.marshall-usa.com 3

ML-702 / Product Description

Front Panel Features

1. Rackmount ears with tilt capability.

Tilt monitor for best visibility or to improve ventilation.

2. Headphone jack. Accepts standard 3.5mm stereo mini-phone plug.

3. POWER button (Lights red in standby mode; green when operating).

4. INPUT select button cycles through SDI, HDMI and Video.

5. F1~F4 user-deﬁned short cut buttons (lighted when selected).

Short Cut: Access the [SETTING] menu page to set user-deﬁned functions.

6. Menu Knob. Turn without pressing to adjust headphone volume.

Press to open menu system.

Product Description

Back Panel Features

1. Push-on Power Connector

12V DC power input 5.5mm x 2.1mm push-on connector.

Plug the supplied DC power adapter here. (Center pin is +)

Important: Please connect only one type of power supply at a

time to this monitor.

2. 4-pin Power Connector

4-pin XLR DC power input compatible with typical broadcast television camera

12-volt power supplies. CAUTION: Some 4-pin power supplies provide 24 volts.

These are NOT compatible with this monitor. Please check the label on the power

supply before connecting.

Important: Please connect only one type of power supply at a time to this monitor.

Note: Power, TALLY and LAN apply to both screens. Inputs and USB service ports apply to each screen individually.

ML-702 / Product Description

3, 11. HDMI Digital Video Connectors

HDMI input and loop out. Embedded audio may be monitored at the

headphone jack and visually monitored on-screen.

4, 10. Composite Analog Connectors

Video input and loop out. Used for NTSC or PAL composite (CVBS)

video sources.

5, 9. Analog RCA Connectors

Audio left and right inputs. These audio inputs are active only whenever Video is

selected as the source. This audio may be monitored at the headphone jack.

6, 8. Serial Digital “BNC” Connectors

SDI input and loop out. Compatible with SDI, HD SDI and 3G SDI inputs.

Embedded audio may be monitored at the headphone jack and visually

monitored on-screen.

7. USB Service Ports

USB input (Only used

for program upgrades

and LUT load).

12. Ethernet LAN RJ-45 Connector

LAN port. The monitor can be

operated from a Windows™ PC

using the PCSet application

available on Marshall-usa.com.

13. TALLY Connector

A red, green, or yellow on-screen tally bar can be made to appear by

grounding the appropriate pin on the Tally connector as shown in the

table. It is compatible with “open collector” and “pull down” type GPI

controls. Caution: External power should never be applied to the Tally.

Menu Settings

Press MENU knob on the monitor and function menus will pop-up on the screen.

Rotate left or right to select an option. Then press the knob again to open the sub-menu.

When an arrow pointer appears in the menu, turn the Menu knob again to access the

item or press the knob to conﬁrm a selection.

1. PICTURE

This page provides controls for typical picture adjustments.

Brightness – used to establish the correct black level in the picture. Default value is 50.

Contrast – establishes the range of dark to light areas in the picture. Default value is 50.

Saturation – sets the amount of color information in the picture. Default value is 50.

Tint – this function is designed to remove color errors in composite analog (NTSC, PAL)

signals. A better choice for component and digital signals is to use Color Temp / User to

establish the correct color tones. Tint control is only available when VIDEO input is se-

lected. Default value is 50.

Sharpness – adds synthetic “detail” to the image. HD images should require very little

added sharpness. Default value is 0.

Color Temp – this setting provides three different presets for white balance

approximating different common color “temperatures”. USER allows for custom

calibration by adjusting Gains and Offsets as desired:

R/G/B Gain – Adjust the R/G/B Gain of the current Color Temperature from 0 to 255.

Default value is 128.

R/G/B Offset – Adjust the R/G/B Offset of the current Color Temperature from 0 to 511.

Default value is 256.

www.marshall-usa.com 7

ML-702 / Menu Settings

2. MARKER

This page offers controls for setting

various on-screen markers.

Center Marker – places a “+” mark in the exact center of the display.

(Useful for checking camera or graphics positioning.)

Aspect Marker – places borders on screen representing various typical video and

cinema aspect ratios. This does not change the displayed aspect ratio. (That setting is in

the Video menu.)

Safety Marker – places a border around the edge of the screen to be used as a guide

during video production.

Marker Color – the Center, Aspect and Screen marker colors can be changed here.

Grid – On-screen grid lines are useful when matching camera shots or during editing.

When Grid is turned on, Center, Aspect and Safety markers will not appear.

Marker Mat – darkens the background just behind the markers for visibility.

When Grid is turned on, Center, Aspect and Safety markers will not appear.

Thickness – sets the width of the markers. Adjust as desired for best visibility.

3. VIDEO

This page provides controls for picture size,

position and related functions including image

ﬂip, image freeze and Zoom.

Scan – Selects various display methods. When Aspect is selected, the item below this one

can adjust the aspect ratio of the displayed image.

Aspect – Allows changing the aspect ratio (shape) of the picture to match the incoming video.

Settings are available for various video and cinema styles.

Pix-to-pix – displays the incoming video with a 1:1 pixel match. This provides the clearest reso-

lution but usually changes the size of the image. This turns off up/down “scaling”. For example:

a video input that has fewer pixels than the LCD display will appear to shrink while a video input

that has more pixels will appear to expand. This can be useful to determine where artifacts are

occurring by eliminating monitor scaling. When this mode is on, Aspect, Display Scan, Zoom

and Markers will be off.

Zoom – expands the picture. It is normal for picture quality to become less sharp as the picture

is expanded. When this mode is on, Aspect, Display Scan and Markers will be off.

Display Scan – Provides additional methods for viewing images

Full scan – Uses all pixels available in the display. This may not match the aspect ratio of the

incoming signal.

Overscan – enlarge the image slightly to conceal image edges.

Underscan – shrinks the image slightly to allow viewing image edges

Check Field – displays the picture in monochrome (black & white) or in individual primary

colors. Useful for color analysis and troubleshooting.

Freeze – holds the current picture on screen.

Image Flip – the picture can be reversed top to bottom, left to right or both. This can be a useful

tool when viewing images shot through mirrors or from cameras mounted upside-down.

Menu Settings

ML-702 / Menu Settings

4. CAMERA AUX

Peaking - adds a colored edge to picture details making it easy to identify which areas are

in sharpest focus. This is a useful tool to use during camera lens adjustments.

Peaking color – Peaking colors may be changed as needed for best visibility.

Available colors: red, green, blue, white, black. The default color is red.

Peaking level - Use this setting to adjust amount of edge peaking to suit user

preference. Default level is 50.

False Color - a method to show each brightness in the picture with a different color. It

provides a quick way to tell if one part of a picture is too bright or too dark. Each color

represents 10% level change.

Exposure - creates “zebra” lines in the brightest areas of the picture. This mimics a feature

that is commonly found in broadcast camera viewﬁnders which provides a quick way to

check for over-exposure.

Exposure level - Use this setting to adjust the level that zebra lines will appear.

Histogram - is a graphical representation of the tonal distribution within a picture. This

mimics a feature commonly found in DSLR cameras.

This page offers settings to assist

with camera focus.

DSLR – Use the DSLR Preset option to reduce the visibility of on screen indicators shown

with popular DSLR cameras. The available options are: 5D2, 5D3. DSLR option is only avail-

able with HDMI input selected. Aspect and Marker settings are not available in this mode.

VIDEO continued

Menu Settings

5. AUDIO

Volume – controls the Headphone volume. Headphone volume can also be adjusted easily by

using the up/down arrow keys when the menus are not on screen. Default volume setting is 50.

Audio channel – With SDI input, channel pairs may be selected from 1-16. With HDMI input,

Channels 1&2 will be used.

Level Meter – shows an on-screen bar graph of two audio channels (typically Left and Right)

from either an HDMI or SDI digital source.

Mute – Disables the headphone audio output when turned ON.

This Page is used to adjust volume, select audio

channel, enable level meter and mute.

6. SETTING

The Setting page provides a collection of system-level functions including On-

Screen Display (OSD), Ethernet port settings (IP Conﬁg), short cut key (F1 – F4),

and Factory Reset.

Table des matières

Autres manuels Marshall Amplification Moniteur

Marshall Amplification

Marshall Amplification V-R231P-AFHD Manuel utilisateur

Marshall Amplification

Marshall Amplification V-R1041DP-AFHD Manuel utilisateur

Marshall Amplification

Marshall Amplification V-R84P-SDI Manuel utilisateur

Marshall Amplification

Marshall Amplification Monitor V-LCD4-PRO-L Manuel utilisateur

Marshall Amplification

Marshall Amplification V-R171X-DLW Manuel utilisateur

Marshall Amplification

Marshall Amplification M-Lynx-10W Manuel utilisateur

Marshall Amplification

Marshall Amplification AR-DM51-B Manuel utilisateur

Marshall Amplification

Marshall Amplification V-R201-IMD-TE Manuel utilisateur

Marshall Amplification

Marshall Amplification ML-503 Manuel utilisateur

Marshall Amplification

Marshall Amplification V-R241-4K Manuel utilisateur

Marshall Amplification

Marshall Amplification M-LYNX-702 Manuel utilisateur

Marshall Amplification

Marshall Amplification V-R154P Manuel utilisateur

Marshall Amplification

Marshall Amplification V-LCD51 Manuel utilisateur

Marshall Amplification

Marshall Amplification ML-702 W Manuel utilisateur

Marshall Amplification

Marshall Amplification 7" TFT LCD Color Monitor V-ASL7070 Manuel utilisateur

Marshall Amplification

Marshall Amplification V-R171P Manuel utilisateur

Marshall Amplification

Marshall Amplification V-R563P-SDI Manuel utilisateur

Marshall Amplification

Marshall Amplification V-R191P-SDI Manuel utilisateur

Marshall Amplification

Marshall Amplification V-R171P-AFHD Manuel utilisateur

Marshall Amplification

Marshall Amplification V-R70DP Manuel utilisateur

Marshall Amplification

Marshall Amplification ML-454 Manuel utilisateur

Marshall Amplification

Marshall Amplification V-R201-IMD-TE Manuel utilisateur

Marshall Amplification

Marshall Amplification V-R171P-HDA Manuel utilisateur

Marshall Amplification

Marshall Amplification V-RD151P Manuel utilisateur

Manuels Moniteur populaires d'autres marques

Linear Acoustic

Linear Acoustic LQ-1000 Manuel utilisateur

AOC

AOC I2579V Manuel utilisateur

Gateway

Gateway FPD1520 Manuel utilisateur

Furuno

Furuno Mu 120c Manuel utilisateur

Asus

Asus VB171D - 17" LCD Monitor Manuel utilisateur

Dell

Dell S2230MX Instructions d'utilisation

Philips

Philips 107C64 Manuel utilisateur

Dell

Dell S2409WFP Manuel utilisateur

EverFocus

EverFocus EN-7517E Manuel utilisateur

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Manuel utilisateur

Dell

Dell Precision 7680 Mode d’emploi

LG 50PM1M - - 50" Plasma Panel Manuel utilisateur

Bosch

Bosch DDU 9 Manuel utilisateur

Acer

Acer A231HL Manuel utilisateur

Philips

Philips 86BDL4152T Manuel utilisateur

NEC

NEC AccuSync LCD5V Manuel utilisateur

Emay

Emay SleepO2 Manuel utilisateur

IBM

IBM 6360 Instructions d'installation