Marmitek M228 Manuel utilisateur
20046/010703 • M228
MARMITEK M228
DOORPHONE
SYSTEM
OWNER’S MANUAL 2
BETRIEBSANLEITUNG 16
NOTICE D’UTILISATION 28
GEBRUIKSAANWIJZING 48
• 2 WIRE SYSTEM
• BUILT-IN MEMORY (17 PICTURES)
WITH TIME ND D Y RECORDING
• UP TO 8 MONITOR ST TIONS
• CONNECT UP TO 2 DOORC MER ’S ND
M XIMUM OF 3 DOME C MER ’S
ENGLISH
2M RMITEK
M RMITEK 228 DOORPHONE SYSTEM
M228 Standard Parts
ENGLISH
WIRING DI GR M
3M228
Operating Controls:
1. Connector Socket
2. iring Terminals
3. DC Power Socket
4. Sony 4" flat CRT
5. Power LED
6. Handsfree Volume Control
7. Intercom and Broadcast Button
8. Lock Release Button
9. Video and Audio Monitoring
10. Brightness Control
11. Memory Status LED
12. Contrast Control
13. Infra Red Illumination LED’s
14. CCD Camera
15. Call Button
16. Door Unit Assembly Screw
17. all Mount Screws
18. Screw rench
19. Cover Label
20. AC Powersupply
Avoid wiring along AC cords
Lock Release Control
ENGLISH
4M RMITEK
M228 B SE ST TION INST LL TION
STEP1:
Place the all Mount Plate approx. 150-170 cm from ground level, arrange wiring for:
a. the doorunit (2 wires, 0,75 mm2for max. 60 meters distance or 1,0 mm2for max. 100 meter
distance)
b. The AC poweradaptor (supplied)
150-170 cm from ground
Connect the wiring for the doorunit to terminal DR1 (no
polarity)
To AC outlet: do not connect yet.
2 wires
2 wires to connect the lock
Release Control (if available)
ENGLISH
5M228
STEP 2:
To mount the doorunit, first mount the metal all Plate. Connect the 2 wires from the base-station
(monitor) to the terminals "MONITOR" (no polarity). If required, connect 2 wires for the Lock Release
Control to the terminals "DOOR RELEASE". See the schematics below for more details.
Place the doorunit on the metal all Plate, and mount with the screw (16) supplied.
Door camera
Power supply
24V/1A max
Electric door lock
Door camera
24V/1A MAX
Electric door lock
Door open output terminal
By pressing the middle button of the base
station, an electric door lock can be
controlled. The door lock is connected to the
DOOR RELEASE output terminals at the back
side of the door camera. By repositioning the
jumper at the back side of the camera you
can choose between two options:
1. Electric door lock with its own
powersupply (standard)
The door-open contact is a dry contact.
Maximum load DC24V / 1A.
Schematic:
Connection for existing doorbell
On the Marmitek EX-228D door camera, (part
of the Marmitek M228 system) an existing
doorbell can be connected. As a result, the
existing doorbell will be activated when the
button of the EX-228D camera is pressed.
To connect the doorbell system to the door
camera, a small output terminal is available at
the back of the EX-228D door camera. A hook
up wire for this terminal is supplied. You’ll find
this wire in the plastic bag with the
accessoires. The maximum voltage and
current that can be switched with this terminal
(dry contact) is 12V/50mA.
The actual doorbell current of most doorbell
installations is higher and therefore it has to
be switched with a relay. The relay is
controlled by the extra output terminal of the
camera.
2. Electric door lock powered by
M228 system
The door open contact provides the power for
the electric door lock. Output voltage 12V,
maximum current 300mA. Schematic:
6M RMITEK
ENGLISH
STEP 3:
Plug in the AC adaptor of the base station (monitor)
STEP 4:
Press the Audio-Video Monitoring button (4) to test the system.
2 wires to DR1
terminals of the
Base station
(monitor)
2 wires to connect a Lock Release
Control (if available)
7M228
ENGLISH
STEP 5:
Adjust the View Angle of the Door Unit.
Use the supplied Screw rench,
and push the built-in camera unit
gently to the front to adjust the
angle (use resp, left or right hole to
adjust to the required direction).
STEP 6:
Assemble the Door Unit.
Apply the screw (16) and use the adhesive label to cover the screw.
8M RMITEK
ENGLISH
M228-B SE ST TION SET-UP
Press and hold the left button (7) for 2 seconds. A "beep"indicates you enter into the Set Up mode.
A Menu screen is displayed on the monitor screen.
By pressing the left (7) and right (9) button you can step
through the Menu options.
ith the middle (8) button you can change the settings.
• hen the Memory LED [11] flash, the time settings has
to be programmed. The built-in back up battery will
hold the settings during 4 hours in case of power
failure.
• GRAY LEVEL: Setting for the picture resolution (quality)
of pictures stored in the memory.
LO (17) for lower resolution and max. 17 pictures.
HI (13) for higher resolution and max. 13 pictures.
Changes in the Gray Level mode might cause loose of
pictures stored in the memory.
• In case of power faillure, settings and stored pictures
will be hold.
• CAM3, CAM2, DR2/CAM1 should remain in OFF position
if no expansions are installed.
• Pick-up Handset and place it back for ending the Set-
Up mode.
9M228
ENGLISH
M228 – B SIC ST TION (OPER TIONS)
1. Visitor calls from door unit:
•
After 4 seconds, the Marmitek
Videodoorphone auto-
matically records the
picture in its memory.
• If there is no pick-up of the Handset, the connection will be automatically switched off 30
seconds after last call trigger.
• If the Handset is picked up, it will be switched off after 90 seconds, or earlier if the Handset is
replaced on the monitor unit.
• If the Handset is not activated (e.g. nobody home), the Memory LED (11) will slowly flash to
indicate that new pictures are stored in the memory.
2. udio and Video Monitoring without activitating the Handset.
• Press on the right Button (9) for monitoring
without activating the Handset
• If more Doorunits or camera’s are connected,
you may select the required camera by
pushing the button 2, 3 or 4 times.
• Mode will end automatically after 90 seconds,
or if handset is picked up. Mode is also ended
if a visitor calls from the doorunit.
DING DONG
DING DONG
Activation of
Audio and
Video.
Lock Release
Volume adjustment
(only for hands-free mode)
DING DONG
DING DONG
10 M RMITEK
ENGLISH
3. Watching new added frames in the memory.
• If the Memory Status LED (11) flashed slowly, a non watched picture has been captured.
• Press the middle button (8) for at least 2 seconds. A beep indicated you are entering into the
Memory mode. The most recent captured picture is displayed.
• ith the left (7) of right (8) button you can scroll through all the pictures in the memory. The
capture date and time is displayed for your information.
• To leave the Memory mode, pick-up the handset of it is cancelled if a visitor calls from the
doorunit.
4. Other Functions:
• Memory LED indicator (11) flashes (fast) to indicate that a major power failure occured and the
time/date settings have to be renewed (See: M228 Base Station Set-Up).
Memory LED indicator
Autres manuels pour M228
1
Table des matières
Langues :
Autres manuels Marmitek Système d'interphone
Marmitek
Marmitek DOORGUARD 350 Manuel utilisateur
Marmitek
Marmitek DoorGuard400TM Manuel utilisateur
Marmitek
Marmitek DOORGUARD 470 Manuel utilisateur
Marmitek
Marmitek M229 Manuel utilisateur
Marmitek
Marmitek 120 Manuel utilisateur
Marmitek
Marmitek BOOMBOOM 100 Manuel utilisateur
Marmitek
Marmitek DOORPHONE 170 Manuel utilisateur
Marmitek
Marmitek VIDEO DOORPHONE Manuel utilisateur
Marmitek
Marmitek Digimax 210 Manuel utilisateur
Marmitek
Marmitek M228 Manuel utilisateur
Marmitek
Marmitek DOORGUARD300TM Manuel utilisateur
Marmitek
Marmitek Doorguard 100 Manuel utilisateur
Marmitek
Marmitek DoorGuard 300 Manuel utilisateur
Marmitek
Marmitek DP150 Manuel utilisateur
Marmitek
Marmitek DOORGUARD 450 Manuel utilisateur
Marmitek
Marmitek Doorguard 100 Manuel utilisateur
Marmitek
Marmitek Proguard PGI850 Marmitek Manuel utilisateur
