marinco SPL-12W Mode d’emploi
Precision Spotlight Instructions Precision Spotlight Instructions
For more information and installation guides,visit
our website: www.marinco.com
For a FREE catalog of Marinco Recreational
Group products, contact your local dealer or visit
Marinco.com.
marinco.com
ZX447
MAR_TL_029_1011
LIMITED WARRANTY
For five (5) years from the date of purchase, Marinco will, at its discretion, repair or replace
for the original consumer, free of charge, any part or parts found upon examination by
Marinco to be defective in material or workmanship or both. All transportation charges under
this warranty must be borne by the consumer.
Proof of purchase is required. Proof of purchase must be a computerized receipt.
Handwritten receipts are not accepted.
THERE IS NO OTHER EXPRESSED WARRANTY. IMPLIED WARRANTIES, INCLUDING THOSE
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO
ONE YEAR FROM THE DATE OF PURCHASE. THIS IS THE EXCLUSIVE REMEDY AND
CONSEQUENTIAL DAMAGES ARE EXCLUDED WHERE PERMITTED BY LAW.
FCC
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUB-
JECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE
HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFER-
ENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED
OPERATION.
502-2 & 503-2 instructions
Instructions
marinco.com
Installing and Using the
Precision Spotlight
IMPORTANT!
READ THESE INSTRUCTIONS BEFORE INSTALLING AND USING THIS PRODUCT.
INTRODUCTION
The Marinco Precision spotlight uses a super bright 100 Watt, replaceable H3 Halogen bulb
that produces a rich yet intense beam that can illuminate objects up to 1,000ft away. It is
IP56 Weatherproof rated with a double o-ring sealed base, UV weather resistant housing
and fully enclosed tilt function driven by quiet motors that can withstand extreme tempera-
tures (5°F to 113°F or -15°C to 45°C). It has been designed and tested to withstand the
harsh marine environments including high humidity, salt water spray, shock, and vibration.
Innovative construction allows for upside down mounting and reverse motion programming.
Precision circuitry allows for remarkable aiming and tracking with two speed choices.
The Precision remotes have glow in the dark buttons and include one touch Automatic
Sweep and SOS options. The wireless remotes transmit a signal up too 200ft (60m). While
the spotlight comes with a wireless bridge remote there are two more optional remotes:
a wireless handheld remote w/lanyard (SPRL-1) and a hard wired bridge mount remote
(SPRL-3).
PACKAGE INCLUDES:
• Spotlightwith12Voltbulbinstalled
• Additional24Voltbulb**
• Mountingkit(nofastenersincluded)
• WirelessBridgeRemote
• Instructionmanual
**(modelsSPL-12W,SPL-12B,SPL-12Conly)
MODELS: SPL-12W, SPL-12B, SPL-12C
MAR_TL_029_1011_Precision_Spotlight_ Manual_6x9_Ins.indd 1-2 11/3/11 11:15 AM
Precision Spotlight Instructions Precision Spotlight Instructions
Required for Installation:
• Four(4)No.10stainlesssteelpanheadscrewsforspotlightbracket(Length and type of
screws to be determined by mounting surface)
• Two(2)No.6stainlesssteelpanheadscrews(Length and type of screws to be
determined by mounting surface)
• Two(2)#16AWGbuttwireconnectors
WARNING: IF THE APPLICATION IS 24 VOLTS. THE 12 VOLT BULB WILL NEED TO BE
REPLACED WITH THE 24 VOLT BULB.TO REPLACE THE BULB REFER TO THE BULB
REPLACEMENT SECTION. (PAGES 4-5).
Failure to use the appropriate bulb wattage will damage the spotlight.
WARNING: BEFORE OPERATION REMOVE BLUE FILM FROM LENS. FAILURE TO
REMOVE FILM WILL DAMAGE THE SPOTLIGHT.
Mounting and wiring of the Precision Spotlight
1. Select a flat surface to mount the spotlight. Make sure there are no obstructions around
the spotlight that could interfere with the rotation. (template included with light). Be sure you
will have wiring access to the underside of the chosen location and that drilling holes will
not damage existing wiring or structures. Avoid locations where lines, anchors and sails
might entangle or damage the light.
2. Refer to the template for mounting and wire hole location.
3. While installing the mounting bracket make sure that the securing screw is opposite the
direction that the light will be facing. Mark the mounting holes and center wire hole.
Be sure that there is at least a 6"(145mm) radius of clearance from the center hole.
See dotted line on figure 1.
4. Drill hole sizes appropriate for the type of screws or bolts being used. Note: the maximum
bracket whole sizes are No. 10 screws.
5. Drill the appropriate hole size to accommodate the wires. This will depend on the type of
wire being used.
6. The spotlight requires 12 or 24 volt power supplied through appropriate gauge wire.
(Note: If the wired bridge remote version is used than 2 additional wires will need to
be routed from the remote to the spotlight.)
WARNING: CORRECT WIRE SIZE FOR THE RUN AND CIRCUIT BREAKER PROTECTION
NEEDS TO BE SELECTED BASED ON ABYC STANDARDS. FAILURE TO FOLLOW ABYC
STANDARDS MIGHT LEAD TO SEVERE INJURY, DEATH OR DAMAGE TO VESSEL.
7. Mount the bracket. But first apply a small amount of non silicone sealant to where the
screws or bolts penetrate the mounting surface. (Note: mounting bracket screw
heads should not protrude more than .2” (5mm) above mounting bracket.)
8. Connect wires to spotlight using butt connectors. Red wire is positive,
Black wire is negative.
WARNING: POLARITY OF THE WIRES NEEDS TO BE CORRECT TO OPERATE THE
SPOTLIGHT! FAILURE TO WIRE CORRECTLY WILL DAMAGE THE SPOTLIGHT
SYSTEM!
9. Slide spotlight over mounting plate making sure the wires are not pinched and the two
holding tabs engage the light in the proper location. Align the external screw hole with
the screw threads on the mounting plate. This will require a degree of pressure and effort
as the mounting seal must be suitably compressed during this process. Insert securing
screw and ensure that it is fully engaged and secure.
27
FIGURE 1
MAR_TL_029_1011_Precision_Spotlight_ Manual_6x9_Ins.indd 3-4 11/3/11 11:15 AM
Precision Spotlight Instructions Precision Spotlight Instructions
Remote Specifications
Included *
Wireless Bridge Remote
(SPLR-2)
(Optional) †
Hand Held Bridge Remote
(SPLR-1)
(Optional) s
Wired Bridge Remote
(SPLR-3)
Power 12 or 24 Volt
(hard wired to power)
CR2540 button
cell battery
12 or 24 Volt
(hard wired to spotlight)
Current draw
(idle / in use) negligible negligible negligible
Wireless range 200 ft (65m) 200 ft (65m) —
Estimated
battery life — > 40 hours
(continuous use) —
Dimensions 3.5"W x 2.25"H x .75"D
88mm x 57mm x 19mm
2.0"W x 3.78"H x 1"D
51mm x 96mm x 25mm
3.5"W x 2.25"H x .75"D
88mm x 57mm x 19mm
Weight 2.12 oz. (60g) 2.82 oz. (80g) 2.12 oz. (60g)
Housing material UV resistant PC/ASA UV resistant PC/ASA UV resistant PC/ASA
Button material Silicone (glow in the dark) Silicone (glow in the dark) Silicone (glow in the dark)
Wire 16AWG — 24AWG
Operating
temp range 5°F to 113°F (-15°C to 45°C) 5°F to 113°F (-15°C to 45°C) 5°F to 113°F (-15°C to 45°C)
IP Rating IP54 IP56 IP54
Caution: you must feel the screw reach a twist-
ing torque to know that it is properly engaged
Note: In the photograph, the purple and yellow
control wires are shown for the wired-remote. If a
wireless bridge remote is used, then the purple
and yellow leads are not necessary and can be
tucked away within the spotlight base
Mounting the wired and wireless remote
1. The remotes are all IP54 weather resistant.
2. Please choose a mounting location based on the gasket supplied with the remote
(large hole should be towards top)
3. Drill holes the correct size for the mounting screws. The holes through the remotes are
sized for a No. 6 pan head screw. The length and thread type will need to be determined
by the application. Set aside the 2 screw covers.
4. Drill hole for the wiring. Note that the hole needs to be 5/8" to allow the unit to sit flat.
5. If mounting the wireless bridge remote it will require a 12 V or 24 V power source.
If mounting the hard wired bridge remote then it does not need a local power source and
instead uses the 2 wires connecting from the spotlight to the remote. These two
wires will supply the remote with power and control the spotlight. The terminals on the
remote can handle a 16 awg to 26 awg wire. Maximum torque on the terminals is
2.21in lbs (.25 nm)
6. Feed wires through drilled surface hole and gasket from below
7. For the wireless bridge remote attach the power source wires to the remote (+) positive
and (-) negative terminals.
For the hard wired bridge remote attach the 2 wires from the spotlight. The yellow wire
needs to connect to the (+) positive and the purple wire needs to connect to the (–)
negative. Maximum Torque on the terminals is 2.21in lbs( .25 nm)
8. Place remote in location align holes and tighten down.
9. Apply screw caps to remote to hide screws.
PAIRING OF MOUNTED AND HAND HELD WIRELESS REMOTE TO SPOTLIGHT
1. Turn off all power to the spotlight.
2. Apply power to mounted remote. Press and hold the power button on the wireless remote.
3. While pressing the power button apply power to the spotlight.
4. After a few seconds you will hear the relay click and the light will turn on.
5. When the light turns on the paring is complete, release power button.
PROGRAMMING THE REMOTE WHEN MOUNTING THE SPOTLIGHT UP-SIDE-DOWN
NOTE: This procedure reverses the directional buttons on the remote.
1. Pairing of the remote described above must be completed first.
2. Remove all power to the spotlight.
3. Hold down the tilt UP and DOWN buttons on the remote.
4. While pressing the 2 buttons apply power to the spotlight and continue to hold down the
buttons for 3 seconds until the spotlight tilts up or down.
5. The spotlight is now configured for inverted mode. Release buttons.
6. To return the spotlight to the standard configuration repeat steps above.
WARNING: BEFORE OPERATION REMOVE BLUE FILM FROM LENS
SPECIFICATIONS
Description Color Item # OEM #
12/24 Volt, 100 Watt white SPL-12W —
12/24 Volt, 100 Watt black SPL-12B —
12/24 Volt, 100 Watt chrome SPL-12C —
12 Volt, 100 Watt white — SPL-12W.OEM
12 Volt, 100 Watt black — SPL-12B.OEM
12 Volt, 100 Watt chrome — SPL-12C.OEM
24 Volt, 100 Watt white — SPL-24W.OEM
24 Volt, 100 Watt black — SPL-24B.OEM
24 Volt, 100 Watt chrome — SPL-24C.OEM
Replacement Bulbs
Description Item #
12 Volt, H3 Halogen 202319
Replacement Parts
Part# Description
202319 12V, H3 halogen replacement bulb
202320 24V, H3 halogen replacement bulb
SPLR-1 Spotlight remote, wireless hand-held
SPLR-2 Spotlight remote, wireless bridge mount
SPLR-3 Spotlight remote, wired bridge mount
63
* There is no wiring required from the spotlight to the
bridge remote. The spotlight and the bridge remote must
be wired locally to power.
† The hand held bridge remote includes a wrist lanyard
and a surface mount cradle.
s The wired bridge remote requires hard wiring of 2 leads
from the spotlight to the bridge.
Bulb 100 Watt, H3 Halogen (replaceable)
(12 volt installed / 24 Volt included)
Power
(Input voltage)
12 volt or 24 Volt
(note: must match bulb with voltage)
Current draw
(idle / in use) 0.03 Amps / 7.0 Amps
Peak beam
intensity 210,000 candella
Peak beam
distance 917 ft (280 m)
Lux @ 66' (20m) 525 Lux
Coverage at 66'
(20 m)
132 sq Ft
(12 sq m)
Rotatation 370° (built in limit stops)
Tilt 120° Tilt (75°up and 45° down)
Wireless range 200 ft (65m)
Dimensions 7.5"W x 7.5"H x 9.25"D
(19cm x19cm x 23.5cm)
Weight 3.30 lbs (1.5 kg)
Housing material UV resistant PC/ASA
Lens material UV resistant Lexan®
Wire type 16 AWG power
24 AWG control
Operating
temp range 5°F to 113°F (-15°C to 45°C)
IP Rating IP56
Tested in accordance with ANSI/NEMA standard FL1
MAR_TL_029_1011_Precision_Spotlight_ Manual_6x9_Ins.indd 5-6 11/3/11 11:16 AM
Precision Spotlight Instructions Precision Spotlight Instructions
OPERATION
BULB REPLACEMENT CAUTION! AVOID TOUCHING THE GLASS SURFACE OF THE
NEW BULB. (TOOLS REQUIRED: MEDIUM PHILLIPS SCREWDRIVER)
1. Remove 2 screws on bottom of lens bezel
and remove bezel.
2. Remove 6 screws from around the lens.
3. Remove lens and reflector as an assembly.
SOS
(· · · — — — · · ·)
Pressing this button the light will begin to signal the
Morse code distress signal. Press again to turn off
Power on/off
Speed Control
Pressing this button will
allow you to change speed
of the light, SOS, and Sweep
Angle function
Auto Sweep
When this button is pressed
the light will begin to sweep left
and right at 90° for slow speed
and 70° for high speed. Press
the button again or a directional
button to stop the sweep
1. Remove the screw holding the
metal grounding bar behind
the reflector. Remove the bulb
assembly by pushing on the
bulb so it exits the back of the
reflector.
2. Unplug bulb and replace with
new bulb. (or 24 volt bulb if
installation requires)
CAUTION! AVOID TOUCHING THE GLASS SURFACE OF THE NEW BULB.
45
MAR_TL_029_1011_Precision_Spotlight_ Manual_6x9_Ins.indd 7-8 11/3/11 11:16 AM
Autres manuels pour SPL-12W
1
Ce manuel convient aux modèles suivants
5
Autres manuels marinco Mettre en lumière
Manuels Mettre en lumière populaires d'autres marques
Guangzhou Yinhe Lighting&Sound Equipment Factory
Guangzhou Yinhe Lighting&Sound Equipment Factory NE-204 Manuel utilisateur
LIVARNO home
LIVARNO home 375304 2101 Instructions originales
Cameo
Cameo CLQS40WW Manuel utilisateur
Leviton
Leviton Ellipsoid 5/50 Manuel utilisateur
Monacor
Monacor img Stage Line PARL-56PDX/CR Manuel utilisateur
Vector
Vector SL3AKV Manuel utilisateur
EuroLite
EuroLite Akku flat light 1 Manuel utilisateur
Commercial Electric
Commercial Electric SPTM-1401 Manuel utilisateur
Vision & Control
Vision & Control SLB-500-W5K7-P-SL Manuel utilisateur
Teknik
Teknik FLEXI Manuel utilisateur
Craftsman
Craftsman CMXLSB10 Manuel utilisateur
EuroLite
EuroLite LED SLS-144 UV Floor Spot Manuel utilisateur