Marimba One WAVE Manuel utilisateur
Please register your marimba for warranty service at
www.marimbaone.com/ordering/owners-registration
www.marimbaone.com
tel 707 822 9570
fax 707 822 6256
Marimba One
901 O St, Suite D
Arcata, CA 95521
USA
OWNER’S MANUAL
for
Four Inch Wheel Marimba
and
Eight Inch Wheel Marimba
121018 - REV. A PAGE 1 0F 13
Bass Frame
Treble Frame
Sway Block
Rail #1
Rail #2
Rail #3
Rail #4
Accidental Resonator Bank
Natural Bars Accidental Bars
Natural Resonator Bank
Girder
Girder
FOR ASSEMBLY,
YOU WILL NEED:
1 �
KEEP These instructions for future reference
ASSEMBLY INSTRUCTIONS
& OWNER'S MANUAL
CAREFULLY UNPACK YOUR CRATE
Compare the components to this page.
•A large open space with carpet (or a blanket to cover the oor)
•An assistant to help assemble the heavy items
AVOID INJURY – When opening crate,
use wire cutters or scissors to cut zip ties.
OPTIONAL (sold separately)
Accessory Bar
3 �
4 �
2 �
5 �
121018 - REV. A PAGE 2 0F 13
ARRANGE FRAME COMPONENTS
In a large open space with carpeting (or a blanket), arrange the frame components.
Treble Frame
Bass Frame
Girders
LOOSEN KNOBS
Turn knobs counterclockwise.
Push clamp-levers into open position.
Bass Frame
Treble Frame
Bass Frame
Girder
OPEN CLAMP-LEVERS
When you hear or feel the
girder tubes touch, the
girders are fully engaged.
CONNECT GIRDERS
On a at surface, align girders
as shown. Slide slotted end over
metallic end until fully engaged.
metallic end
slotted end
9 �
1 1 �
12 �
10 �
6 �
7 � 8 �
121018 - REV. A PAGE 3 0F 13
ATTACH GIRDER PLATE SECURE GIRDER PLATE
VERIFY CLAMPS AND KNOBS ARE SECURELY TIGHTENED
Tighten frame knobs rmly.
Lower girder plate notches
onto frame knobs.
REPEAT PROCESS FOR TREBLE FRAME
SECURE GIRDERS
Push clamp-lever
into closed position. NOTE: Clamp-lever will not close if
girder ends are not fully engaged.
Have assistant hold bass
frame upright.
ATTACH DIAGONAL BRACE
Holding diagonal brace, lift
girder. Diagonal brace will
swing into open position.
Lower slotted end
of diagonal brace
onto clamp-rod.
SECURE BRACE
Push lever into
closed position.
diagonal
brace
14 � 1 3 �
15 �
16 �
121018 - REV. A PAGE 4 0F 13
The natural resonator bank has a plug
inside every tube.
The accidental resonators are missing a
plug inside every 3rd or 4th tube.
CAUTION:
The resonators are heavy. You will
need an assistant to help move the
resonators into place.
CLOSE SAFETY LOCK
Lock is located at hinge point on resonator bank.
IDENTIFY NATURAL
RESONATOR BANK
UNFOLD RESONATOR
safety lock
With your assistant, carefully lift the natural resonator bank.
INSTALL NATURAL RESONATOR BANK
Bass Frame
Treble Frame
Slide bass end into slots. Set treble end on block.
17 �
18 �
19 � 20 �
21 �
1234
121018 - REV. A PAGE 5 0F 13
INSTALL SWAY BRACE
Slide ends of sway brace into brackets on resonator banks.
Numbers are engraved on the
lower right side on treble end.
Rails are placed in positions with
corresponding rail numbers, as
shown below.
IDENTIFY RAILS 1 – 4UNFOLD RAILS
With your assistant, unfold the rail while
supporting each end.
NOTE: Gaps between the rail jacks
are wider on the bass end of rail.
INSTALL ACCIDENTAL RESONATOR BANK
Repeat steps for the second resonator bank.
sway brace slots
sway brace
PREPARE TO INSTALL RAILS
bass
treble
bass
treble
treble end
Bass Frame
22 �
23 �
1
naturalnatural
accidental
121018 - REV. A PAGE 6 0F 13
Lower rail 1 into slots
and onto pegs.
INSTALL RAIL 1
REPEAT FOR RAILS 2 – 4
2
3
1
4
naturalnatural
accidental
Make sure the rail is fully engaged onto the exible pegs.
Bass Frame
Bass Frame
Treble Frame
Treble Frame
25 �
26 �
24 �
121018 - REV. A PAGE 7 0F 13
2
1
naturalnatural
accidental
Bass Frame
Treble Frame
INSTALL NATURAL BARS
Carefully unroll heaviest bar bundle.
With your assistant at one end and
you at the other. Place natural bars
over rails #1 and #2.
POSITION BARS ON RAILS
Place each bar over a resonator
tube. Bars should be separated
by a pair of Jacks.
Cord should rest on Rail Jacks.
Wrap the bar cord around
Corner Jacks at the treble end.
SECURE BARS TO RAILS
Once all bars are in place, from
bass end, pull cord taut (pulling
evenly on each end of the cord
at the same time), loop cord
around corner jacks and hook
springs together.
bass frame end close-up
FOLLOW SAME PROCEDURE FOR ACCIDENTAL BARS
NOTE: Bars are placed ONLY on resonator tubes that have a plug.
When you look from the top you can see the oor through
the resonators without bars over them.
treble end close-up
corner jacks
rail jacks
tuning arch
bar cord
1 �
2 �
3 � 4 �
CONNECT TUBES
SECURE TUBES
INSTALL ACCESSORY BAR SECURE BAR
Accessory Bar
Push clamp-levers into
closed position.
121018 - REV. A PAGE 8 0F 13
You will need a #2 Phillips head screwdriver.
Slide tubes together.
Insert screw into hole on straight tube.
Using screwdriver, turn screw clockwise
to tighten.
Repeat for all four screws.
With an assistant, lower slotted ends
of accessory bar onto clamp-rods.
bar cord tension
1 �
2 �
3 �
4 �
121018 - REV. A PAGE 9 0F 13
Over time, as you play your instrument, the cord that suspends the
bars may loosen and need to be adjusted. To increase tension in the
bar cord, use the cleats behind the springs to hold the slack in the cord.
cleat cleat
hooks
spring
(bar cord)
UNHOOK SPRINGS
spring
NOTE:
In time, the cord may become
loose again.
Do not exceed a maximum of
THREE loops around each cleat.
RE-HOOK SPRINGS
Slip the loop down around the cleat.
Pull the cord taut.
FORM LOOP IN CORD
SLIP LOOP OVER CLEAT
At cleat, pull cord to make
enough slack to form a loop.
Autres manuels pour WAVE
1
Table des matières
Autres manuels Marimba One Instrument de musique
Marimba One
Marimba One M1 Educational Series Manuel utilisateur
Marimba One
Marimba One Motif Manuel utilisateur
Marimba One
Marimba One WAVE Manuel utilisateur
Marimba One
Marimba One Concert Xylophone Manuel utilisateur
Marimba One
Marimba One Izzy Manuel utilisateur
Marimba One
Marimba One WAVE Xylophone Manuel utilisateur
Marimba One
Marimba One Educational Series Manuel utilisateur
Marimba One
Marimba One One Vibe Manuel utilisateur
Marimba One
Marimba One One Vibe Guide de démarrage rapide
Marimba One
Marimba One Izzy Manuel utilisateur
