Marchetti OLYMPO Fiche technique
MOBILE ACCESS TOWER
OLYMPO
www.marchetti.eu
Instructions Manual EN 1298 – IM – it x en
Mobile access towers must only be used for finishing, maintenance and similar works. This
instructions manual contains important instructions on use, maintenance and safety of the
mobile access tower; the operator must be completely aware of them before use. Strictly
complying with this manual means working in compliance with the provisions of the current
standard on health and safety in the workplace Leg. Decree. 09.04.2008 no. 81.
Code 11115
CUSTOMER ASSISTANCE DOCUMENT
N. 120 REV. 2 DATED 08/01/2018
MARCHETTI S.r.l.
Via Piemonte, 22
06062 Città della Pieve - Perugia - Italy
Tel. + 39 0578 20348 - Fax + 39 0578 226488
info@marchetti.eu
www.marchetti.eu
Instructions for use
and maintenance
European standard EN 1004
The products identified in this handbook have
been manufactured by MARCHETTI s.r.l. With
QUALITY SYSTEM MANAGEMENT, certified by
Tuv Italia, in accordance with ISO 9001
2
www.marchetti.eu
ATTENTION:
• Read and understand this manual in its
entirety.
• Follow the instructions as indicated.
• Before any installation, verify the
integrity of each individual component.
Do not use damaged or not whole
components
!
The mobile access tower is made according to
the standards.
Any changes made by others invalidate the
manifacturer’s responsibility.
IT
3
TABLE OF CONTENTS:
1. REFERENCE STANDARDS pag. 4
2. DESIGNATION, CLASS, CAPACITY pag. 4
3. DECLARATION OF CONFORMITY pag. 5
4 GENERAL INFORMATION pag. 6
4.1 Access to work platform pag. 6
4.2 Maximum heights of the configuration EN 1004 pag. 6
5 IDENTIFICATION pag. 7
Table of elements composing the configurations A1 - A2 - A3 pag. 7
To create configurations with final tower H=0.85 m (A1T-A2T-A3T) pag. 7
simply add the following elements
“OLYMPO” TOWER DESIGN pag. 8
CONFIGURATIONS UNI EN 1004 pag. 9
6. ASSEMBLY AND DISMANTLING pag. 10
6.1 General information pag. 10
6.2 Preliminary tests pag. 10
6.3 Assembly instructions pag. 10
6.4 Dismantling instructions pag. 13
7. STABILITY pag. 13
8. USE pag. 13
8.1 Preliminary controls pag. 13
8.2 Use pag. 14
8.3 Movement procedure pag. 14
9. CHECKS, CARE AND MAINTENANCE pag. 14
• INSTRUCTIONS FOR USE AND MAINTENANCE pag. 15
Legislative Decree 09.04.2008 no. 81
10. GENERAL INFORMATION pag. 16
10.1 Configurations table according to Leg. Decree 81/08 pag. 16
10.2 Access to work platform pag. 17
10.3 Information completion pag. 17
• SIX-MONTHLY SERVICE pag. 18
4
www.marchetti.eu
1. REFERENCE STANDARDS
- Leg. Decree 09.04.2008 no. 81 (O.G. no. 101 dated 30.04.08) “Consolidating act on health and
safety in the workplace”.
- UNI EN 1004 (July 2005) “Mobile access and working towers) composed of prefabricated
elements. Materials, dimensions, design loads, safety and performance requirements”;
- EN 1298 (February 1996) “Mobile access towers. Regulations and guidelines for preparation
of an instructions manual”;
- Leg. Decree 06.09.2005 no. 206 (O.G. no. 235 on 08.10.05 – Ordinary Supplement no. 162)
“Consumers’ Code”.
2. DESIGNATION, CLASS, CAPACITY
OLYMPO working tower EN 1004 – 3 – 5 / 5 XXCD
manufactured in compliance with Leg. Decree 81/08 and Technical Standard UNI EN 1004;
Class of loads distributed uniformly equal to “3” (2.0 KN/m2);
- Maximum height permitted of the working surface equal to 5 metres both outside and inside
buildings. Inside is intended as without wind
- The overall load permitted for each tower is therefore 200 kg.
- The maximum number of surfaces loaded at the same time is 2.
- The sum of the loads relating to each surface must not exceed the overall value of the load
permitted for the scaffolding.
IT
5
3. DECLARATION OF CONFORMITY
www.marchetti.eu
DECLARATION OF CONFORMITY
MARCHETTI s.r.l.
with headquarters in Città della Pieve (Pg) - Via Piemonte, 22:
- that the mobile tower called OLYMPO was manufactured
in compliance with Leg. Decree 09.04.2008 no. 81 and in
particular the Technical Standard EN 1004 (July 2005))
- that it is manufactured in compliance with the prototype which
has surpassed rigidity testing, pursuant to Appendix “A” of the
Technical Standard EN 1004 (2005) and that it was subject,
with a positive outcome, with the ASSESSMENT as outlined in
point 13 of the Technical Standard EN 1004 (2005) at the:
UNIVERSITY OF PERUGIA
Department of Industrial Engineering
Certificate no. Marc 128
- the identification marking is outlined on all specimens of the
products and on the Instructions Manual drafted according to
specifications in Technical Specification EN1298 (point 9 of
the Technical Standard EN 1004).
DECLARES
6
www.marchetti.eu
4 GENERAL INFORMATION
4.1 Access to work platform
Access to the work platform can only take place inside the tower using one of the following
methods:
- vertical rung ladder, composed of uprights on the side frames of the structure
- inclined rung ladder, internal
- inclined step ladder, internal.
4.2 Maximum heights of the configuration EN 1004
The maximum height of the work platform without using the stabilizer braces is 1.60 metres
(maximum tower height 2,90 metres).
The maximum height of the work platform using the stabilizer braces is 5 metres both inside and
outside buildings.
The minimum open height between the work platform is 1.90 metres.
The maximum vertical distance between the work platform is 4.20 metres.
The maximum vertical distance between the floor and the first level is 4.60 metres.
IT
7
5 IDENTIFICATION
UNI EN 1004 - Class “3” (2.00 KN/m2)
Overall permitted load 200 kg
Maximum number of surfaces loaded simultaneously
Table of elements composing the configurations A1 - A2 - A3
Code Component Elements Weight CONFIGURATIONS
Kg A1 A2 A3
21335 Tower
1 21329 Support frame 5,00 2 4 6
2 21327 Horizontal bar 0,55 2 4 5
3 21328 Diagonal bar 0,75 4 8 12
21325 Work platform
4 20299 Surface with trapdoor - 180 11,00 1 1 1
5 11093 Short toeboards -75 0,75 2 2 2
6 11092 Long toeboards -180 3,00 2 2 2
21324 Guardrail
7 33803 Single parapet 2,00 2 2 2
20770 Stabilizer braces
8 20765 Stabilizer brace - 35 Normal 9,80 0 4 4
9 31377 Joint for stabilizer braces 1,00 0 8 8
21345 Base
10 21326 Wheel support 10,00 2 2 2
11 21331 Connection 3,70 1 1 1
12 30522 Handle screw M12x80 0,14 2 2 2
To create configurations with final tower H=0.85 m (A1T-A2T-A3T)
simply add the following elements
Code Component Elements Weight CONFIGURATIONS
Kg A1T A2T A3T
21332 Final tower
13 33606 Final frame 1,80 2 2 2
2 33592 Connection 0,55 2 2 2
14 33607 Diagonal bar 0,60 4 4 4
8
www.marchetti.eu
“OLYMPO” TOWER DESIGN
BASE
TOWER
FINAL TOWER GUARDRAIL
WORK PLATFORM
STABILIZERS BRACES
14
3
2
2
12
11
10
4
13
1
8
9
7
56
9
IT
9
A1
H Tower = 2,00
H Working = 0,80
A1T
H Tower = 2,90
H Working = 1,60
A2
H Tower = 3,70
H Working = 2,40
A2T
H Tower = 4,60
H Working = 3,30
A3
H Tower = 5,40
H Working = 4,10
A3T
H Tower = 6,20
H Working = 5,00
CONFIGURATIONS EN 1004
10
www.marchetti.eu
6 ASSEMBLY AND DISMANTLING
6.1 General information
a) For assembly and dismantling of the mobile access towers, at least 2 people are necessary
and it is indispensable they are familiar with the assembly and use instructions;
b) based on the height which must be reached, choose to set up one of the configurations
outlined on page 7. The list, the weight and quantity of the elements necessary for assembly
are outlined on page 5.
c) no damaged components must be used;
d) only original parts must be used as indicated by the manufacturer.
6.2 Preliminary tests
a) The surfaces on which the tower is assembled and subsequently moved (if necessary) must
be capable of supporting the weight, it must be perfectly level and guarantee distribution
of the load, perhaps using planks or other equivalent devices;
b) absence must be ensured of obstacles;
c) the assembly operations can only start in the absence of wind;
d) all the elements must be checked, accessory tools and safety equipment to assemble the
tower are available on site;
e) The verticality of the mobile towers must be checked with the level supplied.
6.3 Assembly instructions
Having conducted the checks on par. 6.2, proceed to assemble the base section:
Check the 2-wheel support blocks with
the base batten using the 2 handle screws,
supplied.
Before completely tightening the screws,
assemble the first 2 side frames and insert
the fastening pins in the hole on the base
sleeve. Tighten the screws, proceed to insert
the brakes in the 4 wheels and, if using the
adjustable feet, on horizontal extraction of
these, the maximum quantity compatible
with the surrounding dimensions, a specific,
automatic device prevents its unintentional
removal, then tighten the extraction fastening
screw; then, level the base section working on
the feet screw and having taking care to lift all
the wheels off the ground at least 20 metres,
on levelling tighten the specific counter-nuts.
Table des matières
Autres manuels Marchetti Ordinateur de bureau
