Mantis 7920 Manuel utilisateur

QUICK ASSEMBLY SHEET

Models:7920, 7921, 7924, 7925, 7940 Tools Needed: Two 7/16” wrenches

Tighten Hardware Tine Installation

Honda engine shown. Engine type depends on the model of the tiller.

Attach the Upper Throttle

Handle onto the Right Lower

Handle. Fasten together using

the Knob T12 and carriage bolt

T42. Place an acorn nut T13 on

the end of the carriage bolt.

Repeat this process for the Left

Upper Handle.

Upper Handles

Step 3

Slide the tines onto the

axle shafts. The “D-

shaped” hole goes on the

outside. Secure each tine

to the axle by inserting a

tine retaining pin T41.

Step 7

Tighten all lock nuts, cap

screws, and bolts firmly and

securely using two 7/16”

wrenches.

Note: Do not over-tighten the

acorn nuts.

Step 6

Throttle Clip

Use the clip T9 to secure

the throttle cable and

wire in place on the Right

Lower Handle.

Step 4

Lower Handles

Slide two (2) T11 bolts through the holes

of one Handle Clamp and then through

the holes of the Left Lower Handle.

Position the bolts so that one bolt is in

front and one bolt is behind the

recessed channels of the transmission

housing. Slide the Right Lower Handle

and the second Handle Clamp onto the

bolts. Finger tighten the nuts T14.

Step 1

Slide the Carrying Handle

over both Lower Handles.

Slide it down towards the

engine. It will rest about

four to six inches above the

engine.

Step 2

Carry Handle

Hardware

T15

T42

T13

T12

T14

T41

T11

T15 - ¼-20 x 1.125” cap screws

T42 - ¼-20 x 2.25” carriage bolts

T13 - Acorn Nut

T41 - Tine Retaining pins

T11 - ¼-20 x 3” hex bolt

T14- ¼-20 two-way lock nut

T9- Throttle clip

T7- Clamp

T12- Knob

Line up the Handle Brace with

the holes on the Upper Handles.

Insert cap screws T15 through

the holes in the Handle Brace and

through the holes on the Upper

Handles. Secure with a lock nut

T14.

Handle Brace

Step 5

QUICK ASSEMBLY SHEET

Kickstand Assembly for Models 7924, 7925, 7940

Tools Needed: 3/8” wrench.

P/N 430094 , Rev A

IMPORTANT NOTE:

Read the Safety Rules &

Warnings before you

use your Mantis tiller

Place the Bottom Bracket of

the Kickstand Stand

Assembly T49 under the

Lower Handles and line up

the holes in both brackets.

Step 9

Insert two screws through the

holes in the Top Bracket and into

the threaded inserts of the Lower

Bracket. Tighten with the 3/8”

wrench.

Step 10

Lean the Tiller Handles against a sturdy

surface, so the tiller is supported in the

upright position. Place the Top Bracket

over the Lower Handles and below the

Carry Handle.

Step 8

Top Bracket Tighten Hardware

Bottom Bracket

Place the Kickstand in the

folded position. The

Kickstand should be centered

between the Lower Handles.

If not, loosen the screws

slightly, adjust as necessary

and retighten the screws.

Step 11

Kickstand Position

Hardware

T50- Kickstand bracket

and hardware bag

T49- Kickstand

Stand Assembly

T49

T50

Top

Bracket

¼-20 x 0.5”

Flange

Screw

Models

7920,7921 Models

7924,7925 Model

7940

Autres manuels pour 7920

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Mantis Taller

Mantis

Mantis Tiller/Cultivator Manuel utilisateur

Mantis

Mantis SV-5C/2 Manuel utilisateur

Mantis

Mantis 7250 Manuel utilisateur

Mantis

Mantis 7940 Manuel utilisateur

Mantis

Mantis 7234 Manuel de programmation

Mantis

Mantis SV-5C/2 Manuel utilisateur

Mantis

Mantis Tiller/Cultivator Manuel utilisateur

Mantis

Mantis 7234 DELUXE Manuel utilisateur

Mantis

Mantis Tiller/Cultivator Manuel utilisateur

Mantis

Mantis 410733 Manuel utilisateur

Mantis

Mantis Mantis-20 Guide de l'utilisateur

Mantis

Mantis Tiller/Cultivator Manuel utilisateur

Mantis

Mantis Tiller/Cultivator Manuel utilisateur

Mantis

Mantis ElectricTiller Manuel utilisateur

Mantis

Mantis 7222E Manuel utilisateur

Mantis

Mantis Tiller/Cultivator Manuel utilisateur

Mantis

Mantis Tiller Manuel utilisateur

Mantis

Mantis ElectricTiller Manuel utilisateur

Mantis

Mantis 7252 Manuel utilisateur

Mantis

Mantis 7263 Manuel utilisateur

Mantis

Mantis Tiller/Cultivator Manuel utilisateur

Mantis

Mantis 7265 Manuel de programmation

Mantis

Mantis 7945 Manuel utilisateur

Mantis

Mantis XP Manuel utilisateur

Manuels Taller populaires d'autres marques

MTD

MTD 410R Manuel utilisateur

Craftsman

Craftsman 247.29931 Manuel utilisateur

MTD

MTD FRT Series Manuel utilisateur

Craftsman

Craftsman 917.298353 Manuel utilisateur

Troy-Bilt

Troy-Bilt Colt FT Manuel utilisateur

Ryobi

Ryobi 510r Manuel utilisateur

MTD

MTD OHV Series Manuel utilisateur

YAT

YAT YT5601-01 Manuel d'entretien

Craftsman

Craftsman 917.296010 Manuel utilisateur

Troy-Bilt

Troy-Bilt OEM-290-260 Manuel utilisateur

Scheppach

Scheppach MTP560 Instructions de montage

GARDEN WAY

GARDEN WAY 12194 Manuel utilisateur

Classen

Classen STAND-AER SA-25 Instructions d'installation et d'entretien

Craftsman

Craftsman 850 Series Manuel utilisateur

DR PILOT 2 Guide de démarrage rapide

Altrad

Altrad ATIKA BH 1400 N Mode d’emploi

WIL-RICH

WIL-RICH 2500 Manuel utilisateur

Viking

Viking HB 685 Manuel utilisateur