Makita UB1102 Manuel

P 1/ 8

Model No.

Description

Continuous Rating (W)

Voltage (V) Cycle (Hz) Input Output Max. Output (W)

--- ---

110

220

230

240

Nozzle .....................................1

Joint .........................................1

Dust bag (capacity of 2L) .......1 (for some countries)

5.7

2.9

2.8

2.7

50/60

600

--- ---120 6.8 50/60 ---

600

--- ---600

Current (A)

Dimensions: mm (")

Width (W)

Height (H)

Length (L) 479 (18-7/8)

185 (7-1/4)

178 (7)

No load speed: min.ˉ¹=rpm

Max. air volume*1: m³/min.

Max. sealed suction: kPa

Protection against electric shock

Power supply cord: m (ft)

*1 Without Nozzle, Joint

*2 With Nozzle, Joint

16,000

Model No. UB1102

Double insulation

Variable speed control No

4.1

Australia: 0.5 (1.64), Others: 2.5 (8.2)

2.0 (4.3)

5.7

0 - 16,000

UB1103

Yes

0 - 4.1

0 - 5.7

UB1102, UB1103

Blower

Weight according to

EPTA-Procedure 01/2003*2: kg (lbs)

Dust bag assembly

Nozzle assembly

Long nozzle assembly

Flexible hose set

Anchor nozzle set (for vacuum function only)

Bending long nozzle set

PRODUCT

Models UB1102, UB1103 Blowers are successors of UB1100, UB1101.

Their output air volume is 4.1m³/min. over the predecessors 2.8m³/min.

The other features are as follows:

•Ergonomic designed handle with elastomer for more comfortable

and controlled operation

•Self-standing design enables stationary use, easy storage and upside-down

standing

The specification difference between UB1102 and UB1103 is;

UB1102: Single speed

UB1103: Variable speed control by dial and trigger

CONCEPT AND MAIN APPLICATIONS

Specification

Standard equipment

Optional accessories

Note: The standard equipment for the tool shown above may vary by country.

TECHNICAL INFORMATION

P 2/ 8

Repair

It is not required to lubricate, because the product has no gear mechanism to be lubricated.

[3] DISASSEMBLY/ASSEMBLY

[3] -1. Switch

CAUTION: Repair the machine in accordance with “Instruction manual” or “Safety instructions”.

[1] NECESSARY REPAIRING TOOLS

[2] LUBRICATION

Fig. 1

DISASSEMBLING

ASSEMBLING

1. Switch can be disassembled without separating Fan housing complete section. See Fig. 1.

Code No. Description Use for

1R370 connecting Ring terminals to Brush holderRing Terminal Setting Jig

1R063 assembling Field to Motor housing completeGuide Bar for fitting Field

Assemble Switch by reversing the disassembly procedure. Refer to Fig. 1.

Note: When mounting Handle cover, be careful of the following.

• Switch and Lead wire are not pinched with Handle cover.

Refer to Fig. D-2 and Fig. D-3.

• There are no gaps between Handle cover and Fan housing complete.

No.1

No.2

Handle cover

Switch

Fan housing

complete

Handle cover

1. Remove four 4x18 Tapping screws

that secure Handle cover to Motor

housing.

4. Remove Switch from Handle section

of Motor housing complete.

2. Separate Handle cover, pulling toward Fan housing complete side

(pulling toward the direction designated with arrow No.1.)

3. Disassemble Handle cover by broadening Handle cover (pulling

its ends toward the direction designated with arrow No. 2).

Now, Handle cover is removed.

P 3/ 8

Repair

[3] DISASSEMBLY/ASSEMBLY

[3] -2. Fan Section

DISASSEMBLING

Disassemble Fan 110 as drawn in Fig. 2.

Assemble Fan Section by reversing the disassembly procedure. Refer to Fig. 2.

Note: Align the hole on Set plate with the protrusion on Fan cover, and insert Set plate by hand, then push it

with a small screwdriver until it stops.

Refer to the drawing on the top right in Fig. 2.

Fig. 2

ASSEMBLING

Fan cover

Fan 110

M5-8 Hex nut

Flat washer 5

Flat washer 8

1. Remove Nozzle. Nozzle

3. Unscrew five 4x18 Tapping screws

and remove Fan cover.

4. Remove M5-8 Hex nut by turning it

counterclockwise with an impact driver while

holding Fan 110 firmly with a gloved hand.

5. Remove Flat washer 5, Fan 110 and Flat washer 8.

Set plate

Fan cover

2. Remove Set plate by prying it off with

a small slotted screwdriver.

P 4/ 8

Repair

[3] DISASSEMBLY/ASSEMBLY

[3] -3. Motor Section

DISASSEMBLING

(1) Remove Carbon brush as drawn in Fig. 3.

(2) Disassemble Fan section as drawn in Fig. 2.

(3) Disassemble Armature as drawn in Fig. 4.

Fig. 3

Fig. 4

Flat washer 8

Armature

Fan housing

complete

1. Unscrew four 4x35 Tapping

screws and disassemble Fan

housing complete.

2. Remove Flat washer 8 from

Armature shaft.

3. Remove Armature from

Motor housing.

Carbon brush

P 5/ 8

Repair

[3] DISASSEMBLY/ASSEMBLY

[3] -3. Motor Section (cont.)

DISASSEMBLING

(4) Disassemble Field as drawn in Fig. 5.

Fig. 5

Switch

Field lead wire

Handle cover

Ring terminal

Field

1. Unscrew four 4x18 Tapping screws and remove Handle

cover.

3. Disconnect Ring terminals from Brush holders

with a Slotted screwdriver.

Note:

Tapping the edge of Motor housing

with a plastic hammer enables Field

to be removed easily.

4. Unscrew two 5x40 Tapping screws and remove

Field from Motor housing.

2. Disconnect Field lead wires from Switch.

P 6/ 8

Repair

[3] DISASSEMBLY/ASSEMBLY

[3] -3. Motor Section (cont.)

ASSEMBLING

(1) Assemble Field to Motor housing. Refer to the drawing on the middle right in Fig. 5.

Also see Fig. D-2 about the wiring of Field lead wires.

Note: Using 1R063 enables Field to be assembled easily than by hand. See Fig. 6.

(2) Connect Ring terminal to Brush holder using 1R370. See

Fig. 7

Fig. 6

Ring terminal

1R370

Fig. 7

1R063

Field

(3) Connect field lead wires to Switch and mount Handle cover to Motor housing with four 4x18 Tapping screws.

Refer to the drawings on the top left and right in Fig. 5.

(4) Insert Armature into Motor housing. Refer to the drawing on the right in Fig. 4.

(5) Mount Flat washer 8 to the drive end of Armature's shaft. Refer to the drawing on the center in Fig. 4.

(6) Assemble Fan housing complete with four 4x35 Tapping screws. Refer to the drawing on the left in Fig. 4.

(7) Assemble Fan 110 and Fan cover. Refer to Fig. 2.

And then, set Carbon brush. Refer to Fig. 3.

P 7/ 8

Circuit diagram

Wiring diagram

Fig. D-1

Fig. D-2

White

Noise

suppressor

Switch

viewed from Commutator side

Brush

holder B

Brush

holder A

Line filter

Power supply cord

Color index of lead wires' sheath

Black Blue

Brown

Field

connected to

Switch

Field

Motor housing

complete

Wiring of Field lead wires

connected to

Switch

Slit

Field lead wires

Lead wire

holder

1. Mount Filed to Motor housing complete as shown below.

Lead wire (white or blue) of Power supply

cord connected to P2 terminal

Lead wire (black or brown) of Power supply

cord connected to P1 terminal

Note: Noise suppressor and Line filter are not

used for some countries.

2. Route Field lead wires through the slit

and Lead wire holder as shown below.

P 8/ 8

Wiring diagram

Fig. D-3

Noise suppressor

(if used)

Motor housing

complete

Lead wire

holder

Switch

Field

Power supply

cord

See the drawing

on the right in Fig. D-2.

Line filter (if used)

Set Line filter with Field lead wires

between Lead wire holders.

1. Pass Field lead wires through Line filter

and wind them one turn and pass them

again as shown below.

2. Winded Filed lead wires have to be located on

the Motor housing complete side.

Line filter

Handle cover

Field side

Field lead wires

Motor housing complete

Winded Field

lead wires

Autres manuels pour UB1102

Table des matières

Autres manuels Makita Ventilateur

Makita

Makita BBX7600 Guide de l'utilisateur

Makita

Makita UB001G Manuel utilisateur

Makita

Makita UB002C Manuel utilisateur

Makita

Makita DUB362 Manuel utilisateur

Makita

Makita BBX7600CA Manuel utilisateur

Makita

Makita UB001C Manuel utilisateur

Makita

Makita BUB183 Manuel utilisateur

Makita

Makita UB0800 Guide de l'utilisateur

Makita

Makita UB1100 Manuel utilisateur

Makita

Makita XBU02 Manuel utilisateur

Makita

Makita RBL250 Guide de l'utilisateur

Makita

Makita UB002CZ01 Manuel utilisateur

Makita

Makita UB1100 Manuel utilisateur

Makita

Makita DUB362 Manuel utilisateur

Makita

Makita DUB143 Manuel utilisateur

Makita

Makita UB1100 Manuel utilisateur

Makita

Makita UB100D Manuel utilisateur

Makita

Makita BUB360 Manuel utilisateur

Makita

Makita UB1100 Manuel utilisateur

Makita

Makita AS001GZ Manuel utilisateur

Makita

Makita BUB360 Manuel utilisateur

Makita

Makita PM001G Manuel utilisateur

Makita

Makita UB1102 Manuel utilisateur

Makita

Makita DUB186 Manuel utilisateur

Manuels Ventilateur populaires d'autres marques

Weed Eater

Weed Eater VS2000BV Manuel utilisateur

KRAUSMANN

KRAUSMANN U37020-00 Manuel utilisateur

Bosch

Bosch ALB 36 LI Manuel utilisateur

Cub Cadet

Cub Cadet HB425 Manuel utilisateur

GreenWorks Pro

GreenWorks Pro BLB482 Manuel utilisateur

ARIETE

ARIETE 2768 Manuel utilisateur

NuTone

NuTone 331H Manuel utilisateur

GÜDE

GÜDE GLB 200 18 Li-Ion Manuel utilisateur

I.VA.CO.

I.VA.CO. SC Series Mode d'emploi

DeWalt

DeWalt DCE100 Manuel utilisateur

Becker

Becker SV 7.330 Manuel utilisateur

Metabo

Metabo AG 18 Pro Manuel utilisateur

Desa

Desa GA3650TB Manuel utilisateur

Echo

Echo Power Blower PB-230LN Manuel utilisateur

Echo

Echo PB-413H Manuel utilisateur

Black & Decker

Black & Decker BV3100 Manuel utilisateur

Ryobi

Ryobi RY08570 Manuel utilisateur

Haaga

Haaga 355 Manuel utilisateur