Majestic fireplaces DVB4136 Instructions de montage

INSTALLER / CONSUMER

SAFETY INFORMATION

PLEASE READ THIS MANUAL

BEFORE INSTALLING AND USING

APPLIANCE

WARNING!

IF THE INFORMATION IN THIS

MANUAL IS NOT FOLLOWED

EXACTLY, A FIRE OR

EXPLOSION MAY RESULT

CAUSING PROPERTY DAMAGE,

PERSONAL INJURY OR LOSS OF

LIFE.

FOR OUR SAFETY

Installation and service must be

performed by a qualiﬁed installer,

service agency or the gas supplier.

WHAT TO DO IF YOU SMELL GAS:

• Do not try to light any appliance.

• Do not touch any electric switch; do not

use any phone in your building.

• Immediately call your gas supplier from

your neighbor’s phone. Follow the gas

supplier’s instructions.

• If you cannot reach your gas supplier, call

the ﬁre department.

DO NOT STORE OR USE

GASOLINE OR OTHER

FLAMMABLE VAPORS AND

LIQUIDS IN THE VICINITY OF THIS

OR ANY OTHER APPLIANCE.

Direct Vent Gas Fireplace

Models: DVB4136

Homeowner’s Installation and

Operating Manual

CERTIFIED

20012322 1/08 Rev. 3

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future reference.







DVB4136 Direct Vent Gas Fireplace

20012322

Table of Contents

PLEASE READ THE INSTALLATION & OPERATING INSTRUCTIONS BEFORE USING APPLIANCE.

Thank you and congratulations on your purchase of a CFM Corporation ﬁreplace.

IMPORTANT: Read all instructions and warnings carefully before starting installation. Failure to follow these

instructions may result in a possible ﬁre hazard and will void the warranty.

Installation & General Information, Warnings, Cautions ....................................................................3

Commonwealth of Massachusetts Requirements .......................................................4

Operating Instructions Fireplace Dimensions ..................................................................................................5

Locating Your Fireplace ...............................................................................................7

Clearance to Combustibles ..........................................................................................7

Mantels ........................................................................................................................7

Hearth ..........................................................................................................................7

Framing & Finishing .....................................................................................................7

Final Finishing ..............................................................................................................8

Gas Speciﬁcations .......................................................................................................8

Gas Inlet and Manifold Pressures ................................................................................8

High Elevations ............................................................................................................8

Gas Line Installation ....................................................................................................8

Remote ON/OFF Switch Installation ............................................................................9

Alternate Switch Location ............................................................................................9

EB-1 Electrical Box ......................................................................................................9

Optional Top Vent Application ....................................................................................11

General Venting General Venting .........................................................................................................12

General Venting Information - Termination Location ..................................................13

General Information Assembling Vent Pipes .............................................................14

How to Use the Vent Graph .......................................................................................15

Rear Wall Vent Application & Installation ...................................................................15

Vertical Sidewall Application & Installation .................................................................17

Below Grade Installation ............................................................................................21

Vertical Through-the-Roof Application & Installation ..................................................21

Venting Components .................................................................................................24

Operating Instructions Glass Information .......................................................................................................25

Louvre Removal .........................................................................................................25

Window Frame Assembly Removal ...........................................................................25

Glass Cleaning ...........................................................................................................25

Installation of Optional Ceramic Panels .....................................................................25

Replacement of Ceramic Hearth Panels (if provided) ...............................................26

Installation of Logs .....................................................................................................26

Flame & Temperature Adjustment ..............................................................................29

Flame Characteristics ................................................................................................29

Inspecting the Venting System ..................................................................................29

Lighting and Operating Instructions (SIT 820 Valve) .................................................30

Lighting and Operating Instructions (SIT 822 Valve) .................................................31

Lighting and Operating Instructions (AF4000 Valve) .................................................32

Troubleshooting Gas Control (SIT 820 Valve) ...........................................................33

Troubleshooting Gas Control (AF4000 Valve) ..........................................................34

Instructions for RF Comfort Control Valve .................................................................37

Fuel Conversion Instructions .....................................................................................41

Maintenance Cleaning the Standing Pilot Control System ..............................................................44

Replacement Parts ...................................................................................................................................45

Optional Accessories Fan Kits ......................................................................................................................48

Hard (Direct) Wire Hook Up .......................................................................................48

Remote Controls ........................................................................................................49

Ceramic Refractory Panels ........................................................................................49

Decorative Bay Windows ...........................................................................................49

Decorative Frame Trim ..............................................................................................49

Arch/Square Face Kit .................................................................................................50

Warranty ...................................................................................................................................51

Energuide ...................................................................................................................................52

DVB4136 Direct Vent Gas Fireplace

20012322

Installation & Operating Instructions

This gas appliance should be installed by a qualiﬁed installer,

preferably NFI or WETT (Canada) certiﬁed, in accordance with

local building codes and with current CSA-B149.1 Installation

codes for Gas Burning Appliances and Equipment. If the unit is

being installed in a mobile home, the installation should comply

with the current CAN/CSA Z 240.4 code. For U.S.A Installations

follow local codes and/or the current National Fuel Gas Code.

ANSI Z223.1/NFPA 54.

FOR SAFE INSTALLATION AND OPERATION PLEASE

NOTE THE FOLLOWING:

1 . This ﬁreplace gives off high temperatures and should be

located out of high trafﬁc areas and away from furniture

and draperies.

2. Children and adults should be alerted to the hazards of the

high surface temperatures of this ﬁreplace and should stay

away to avoid burns or ignition of clothing.

3. CAUTION: Due to high glass surface temperature chil-

dren should be carefully supervised when in the same

room as ﬁreplace.

Proposition 65 Warning: Fuels used in gas, woodburning or

oil ﬁred appliances, and the products of combustion of such

fuels, contain chemicals known to the State of California to

cause cancer, birth defects and other reproductive harm.

California Health & Safety Code Sec. 25249.6

IMPORTANT:

PLEASE READ THE FOLLOWING CAREFULLY

Remove any plastic from trim parts before turning the

ﬁreplace ON.

It is normal for ﬁreplaces fabricated of steel to give off

some expansion and/or contraction noises during the

start up or cool down cycle. Similar noises are found

with your furnace heat exchanger or car engine. It is

not unusual for your CFM Corporation gas ﬁreplace to

give off some odor the ﬁrst time it is burned. This is due

to the manufacturing process.

Please ensure that your room is well ventilated

-open all windows.

It is recommended that you burn your ﬁreplace for at

least ten (10) hours the ﬁrst time you use it. If the op-

tional fan kit has been installed, place the fan switch in

the “OFF” position during this time.

WARNING: Check with your electronics manufac-

turer before installing a television or other electronic

device above this ﬁreplace.

11. When ﬁreplace is installed directly on carpeting, vinyl tile

or any combustible material other than wood, this ﬁreplace

must be installed on a metal or wood panel extending the

full width and depth of the ﬁreplace.

12. This ﬁreplace requires adequate ventilation and combus-

tion air to operate properly.

13. This ﬁreplace must not be connected to a chimney ﬂue

serving a separate solid fuel burning ﬁreplace.

14. When the ﬁreplace is not in use it is recommended that the

gas valve be left in the OFF position.

This appliance may be installed in an aftermarket

permanently located, manufactured home or mobile

home, where not prohibited by local codes.

This appliance is only for use with the type of gas

indi-cated on the rating plate. This appliance is not

convertible for use with other gases, unless a certi-

ﬁed kit is used.

DVB4136

Certiﬁed To

ANSI Z21.88-2005 / CSA 2.33-2005

Vented Gas Fireplace Heater



�













4. Under no circumstances should this ﬁreplace be modiﬁed.

Parts removed for servicing should be replaced prior to

operating this ﬁreplace again.

5. Installation and any repairs to this ﬁreplace must be

performed by a qualiﬁed installer, service agency or gas

supplier. A professional service person should be contacted

to inspect this ﬁreplace annually. Make it a practice to have

all of your gas ﬁreplaces checked annually. More frequent

cleaning may be required due to excess lint and dust from

carpeting, bedding material, etc.

6. Control compartments, burners and air passages in this

ﬁreplace should be kept clean and free of dust and lint.

Make sure the gas valve and pilot light are turned off before

you attempt to clean this ﬁreplace.

7. The venting system (chimney) of this ﬁreplace should be

checked at least once a year and if needed your venting

system should be cleaned.

8. Keep the area around your ﬁreplace clear of combustible

materials, gasoline and other ﬂammable vapor and liquids.

This ﬁreplace should not be used as a drying rack for cloth-

ing, nor should Christmas stocking or decorations be hung

in the area of it.

9. Under no circumstances should any solid fuels (wood, coal,

paper or cardboard etc.) be used in this ﬁreplace.

10. The ﬂow of combustion and ventilation air must not be

obstructed in any way.

DVB4136 Direct Vent Gas Fireplace

20012322

Installation & Operating Instructions

Requirements for the Commonwealth of

Massachusetts

All gas ﬁtting and installation of this heater shall only be

done by a licensed gas ﬁtter or licensed plumber.

For all side wall horizontally vented gas fueled

equipment installed in every dwelling, building or

structure used in whole or in part for residential

purposes, including those owned or operated by the

Commonwealth and where the side wall exhaust vent

termination is less than seven (7) feet above ﬁnished

grade in the area of the venting, including but not limited

to decks and porches, the following requirements shall

be satisﬁed:

Installation of Carbon Monoxide Detectors

At the time of installation of the side wall horizontal

vented gas fueled equipment, the installing plumber

or gas ﬁtter shall observe that a hard wired carbon

monoxide detector with an alarm is installed on each

additional level of the dwelling, building or structure

served by the side wall horizontally vented gas fueled

equipment. It shall be the responsibility of the property

owner to secure the services of qualiﬁed licensed

professionals for the installation of hard wired carbon

monoxide detectors.

In the event that the side wall horizontally vented gas

fueled equipment is installed in a crawl space or an

attic, the hard wired carbon monoxide detector with

alarm and battery back-up may be installed on the next

adjacent ﬂoor level.

In the event that the requirements of this subdivision

can not be met at the time of completion of installation,

the owner shall have a period of thirty (30) days

to comply with the above requirements; provided,

however, that during said thirty (30) day period, a

battery operated carbon monoxide detector with an

alarm shall be installed.

Approved Carbon Monoxide Detectors

Each carbon monoxide detector as required in

accordance with the above provisions shall comply with

NFPA 720 and ANSI/UL 2034 listed and IAS certiﬁed.

Signage

A metal or plastic identiﬁcation plate shall be

permanently mounted to the exterior of the building at

a minimum height of eight (8) feet above grade directly

in line with the exhaust vent terminal for the horizontally

vented gas fueled heating appliance or equipment. The

sign shall read, in print size no less than one-half (1/2)

inch in size, “GAS VENT DIRECTLY BELOW, KEEP

CLEAR OF ALL OBSTRUCTIONS”.

Inspection

The state or local gas inspector of the side wall

horizontally vented gas fueled equipment shall not

approve the installation unless, upon inspection, the

inspector observes carbon monoxide detectors and

signage installed in accordance with the provisions of

248 CMR 5.08(2)(a)1 through 4.

Exemptions

The following equipment is exempt from 248 CMR

5.08(2)(a)1 through 4:

• The equipment listed in Chapter 10 entitled

“Equipment Not Required To Be Vented” in the most

current edition of NFPA 54 as adopted by the Board;

and

• Product Approved side wall horizontally vented gas

fueled equipment installed in a room or structure

separate from the dwelling, building or structure

used in whole or in part for residential purposes.

MANUFACTURER REQUIREMENTS

Gas Equipment Venting System Provided

When the manufacturer of Product Approved side

wall horizontally vented gas equipment provides a

venting system design or venting system components

with the equipment, the instructions provided by the

manufacturer for installation of the equipment and the

venting system shall include:

• Detailed instructions for the installation of the venting

system design or the venting system components;

and

• A complete parts list for the venting system design or

venting system.

Gas Equipment Venting System NOT Provided

When the manufacturer of a Product Approved side

wall horizontally vented gas fueled equipment does

not provide the parts for venting the ﬂue gases, but

identiﬁes “special venting systems”, the following

requirements shall be satisﬁed by the manufacturer:

• The referenced “special venting system” instructions

shall be included with the appliance or equipment

installation instructions; and

• The “special venting systems” shall be Product

Approved by the Board, and the instructions for

that system shall include a parts list and detailed

installation instructions.

A copy of all installation instructions for all Product

Approved side wall horizontally vented gas fueled

equipment, all venting instructions, all parts lists

for venting instructions, and/or all venting design

instructions shall remain with the appliance or

equipment at the completion of the installation.

DVB4136 Direct Vent Gas Fireplace

20012322

Fireplace Dimensions (Installed as Top Vent)

Fig. 1 Fireplace speciﬁcations and framing dimensions.

Ref. DVB4136

A 40” (1016 mm)

B 36¹⁄₈” (918 mm)

C 36¹⁄₈” (918 mm)

D 24¹⁄₈” (613 mm)

E 6” (152 mm)

F 6” (152 mm)

G 1” (25 mm)

H 20⁵⁄₈” (524 mm)

I 7¹⁄₂” (191 mm)

J 22⁵⁄₈” (575 mm)

K 5/8” (16 mm)

L 15” (381 mm)

M 3⁵⁄₈” (92 mm)

N 7¹⁄₂” (191 mm)

O 2¹⁄₈” (54 mm)

P 7” (178 mm) Dia.

Q 4” (102 mm) Dia.

Framing Dimensions

R 40³⁄₈” (1026 mm)

S 40¹⁄₄” (1022 mm)

T 20⁵⁄₈” (524 mm)

U 64³⁄₄” (1645 mm)

V 45³⁄₄” (1162 mm)

W 32³⁄₈” (822 mm)

X 40” (1016 mm)

12322

DVB4136 top specs

7/07 djt

S - Rough Opening Width

Rough

Opening

Height

Rough

Opening

Depth

Gas Line

Access

Recessed

Nailing Flange

Electrical Access

DVB4136 Direct Vent Gas Fireplace

20012322

Fireplace Dimensions (Installed as Rear Vent)

Fig. 2 Fireplace speciﬁcations and framing dimensions.

Ref. DV4136

A 40” (1016 mm)

B 36¹⁄₈” (918 mm)

C 36¹⁄₈” (918 mm)

D 24¹⁄₈” (613 mm)

E 6” (152 mm)

F 6” (152 mm)

G 1” (25 mm)

H 20⁵⁄₈” (524 mm)

I 22⁵⁄₈” (575 mm)

J 5/8” (16 mm)

K 15” (381 mm)

L 3⁵⁄₈” (92 mm)

M 7¹⁄₂” (191 mm)

N 2¹⁄₈” (54 mm)

O 30³⁄₄” (781 mm)

P 31⁵⁄₈” (803 mm)

Framing Dimensions

Q 40³⁄₈” (1026 mm)

R 40¹⁄₄” (1022 mm)

S 20⁵⁄₈” (524 mm)

T 64³⁄₄” (1645 mm)

U 45³⁄₄” (1162 mm)

V 32³⁄₈” (822 mm)

W 40” (1016 mm)

12322

DVB4136 rear specs

7/07 djt

R - Rough Opening Width

Gas Line

Access

Rough

Opening

Height

Rough

Opening

Depth

Recessed

Nailing Flange

Electrical

Access

DVB4136 Direct Vent Gas Fireplace

20012322

Clearance to Combustibles

Top of unit to ceiling ................................. 36” (914 mm)

Front of unit to combustibles ................... 36” (914 mm)

Appliance

Top of standoff ....................................... 0” (0 mm)

Bottom ..................................................... 0” (0 mm)

Side ......................................................... 0” (0 mm)

Back ........................................................ 0” (0 mm)

Venting

Concentric sections of DV Vent ................... 1” (25 mm)

Nonconcentric sections of DV Vent

Sides and bottom .................................. 1” (25 mm)

Top ........................................................ 2” (51 mm)

Mantels

The height that a combustible mantel is ﬁtted above the

ﬁreplace is dependent on the depth of the mantel. This

also applies to the distance between the mantel leg (if

ﬁtted) and the ﬁreplace.

For the correct mounting height and widths, refer to

Figures 4a, 4b and the Mantel Chart below.

The distances and reference points are not affected by

the ﬁtting of a bay window front trim kit.

Noncombustible mantels and legs may be installed at

any height and width around the appliance. When using

paint or lacquer, it must be heat resistant to prevent

discoloration.

CFM146

Bottom of Door Trim

Mantel Chart

Mantel Shelf Mantel from Top

Ref. or Breast Plate Ref. of Comb. Chamber

Depth

V 10” (254 mm) A 19” (483 mm)

W 8” (203 mm) B 17” (432 mm)

X 6” (152 mm) C 15” (381 mm)

Y 4” (101 mm) D 13” (330 mm)

Z 2” (51 mm) E 11” (279 mm)

Fig. 4a Combustible mantel minimum installation.

Hearth

A hearth is not mandatory, but is recommended for

aesthetic purposes. We recommend a noncombustible

hearth which projects out 12” (305 mm) or more from

the front of the ﬁreplace.

Cold climate installation recommendation:

When installing this unit against a non-in-

sulated exterior wall or chase, it is manda-

tory that the outer walls be insulated to

conform to applicable insulation codes.

EAB

LU584-1

Locating unit

2/4/99 djt

Locating Your Fireplace

LU584-1

A) Flat on wall B) Cross corner C) **Island

D) *Room divider E) *Flat on wall corner F) Chase installation

Y) 0” minimum (Check minimum if mantel leg is used)

NOTE (Fig. 3):

** Island (C) and Room Divider (D) installation is possible as long as

the horizontal portion of the vent system (X) does not exceed 20’ (6

m). See details in Venting Section.

* When you install your ﬁreplace in(D) Room divider or (E) Flat

on wall corner positions (Y), a minimum of 6“ (152 mm) clearance

must be maintained from the perpendicular wall and the front of the

ﬁreplace.

Fig. 3 Locating gas ﬁreplace.

Framing and Finishing

Check ﬁreplace to make sure it is levelled

and properly positioned.

To mount the appliance: Choose the location. (Fig. 5)

1. This unit comes with four (4) ﬂanges pre-mounted

on both sides of the ﬁreplace to allow two different

drywall thicknesses to be used. Flange “A” is for 1/2”

drywall while ﬂange “B“ is for 5/8” drywall.

2. Bend the desired ﬂanges out 90° on both sides of

the ﬁreplace. Slide the ﬁreplace into the framed

opening until the ﬂanges contact the front surfaces

of the framing. Level the unit and secure it ﬁrmly in

place.

A B C DE

Fireplace

CFM146

DV Mantel Chart

7/5/01 sta

Louvre Assembly

top

Top of Combustion

Chamber

Standoff

Noncombstible

Material

3/4” (19 mm) Scribe moulding

for use with CFMCabinets

DVB4136 Direct Vent Gas Fireplace

20012322

Mantel

Leg

CFM164a

Mantel Leg Chart

06/22/01 sta

CFM170

DV Builder Front

View

Black

Surround

Face

CFM164a

Side of

Combustion Chamber

CFM170

Mantel Mantel Leg from Side

Ref. Leg Depth Ref. of Comb. Opening

F 10” (254 mm) K 11¹⁄₂” (292 mm)

G 8” (203 mm) L 9¹⁄₂” (241 mm)

H 6” (152 mm) M 7¹⁄₂” (191 mm)

I 4” (101 mm) N 5¹⁄₂” (140 mm)

J 2” (51 mm) O 3¹⁄₂” (89 mm)

Fig. 4b Combustible mantel leg minimum installation.







Flange Drywall

Position Depth

A 1/2” / 13 mm

B 5/8” / 16 mm

Flange Location for

Desired Drywall Depth

FP1539

Fig. 5 Drywall ﬂange location.

Final Finishing

Noncombustible materials such as brick or tile can be

extended over the edges of the face of the ﬁreplace.

Do not cover the window frame assembly, any vent,

louvre assembly top or louvre assembly bottom. If

a Trim Kit is to be installed, brick and tile will have to be

installed ﬂush with the side of this appliance.

Gas Speciﬁcations

Max. Min.

Gas Input Input

Model Fuel Control BTU/h BTU/h

DVB4136RN Natural Gas Millivolt Hi/Lo 30,000 18,500

DVB4136RP Propane Millivolt Hi/Lo 30,000 17,000

DVB4136IN Natural Gas 24 Volt Hi/Lo 30,000 21,800

DVB4136IP Propane 24 Volt Hi/Lo 30,000 21,300

DVB4136RFN Natural Gas Comfort Control 30,000 21,000

DVB4136RFP Propane Comfort Control 30,000 23,500

Gas Inlet and Manifold Pressures

Natural LP (Propane)

Minimum Inlet Pressure 5.5” w.c. 11.0” w.c.

Maximum Inlet Pressure 14.0” w.c. 14.0” w.c.

Manifold Pressure 3.5” w.c. 10.0” w.c.

High Elevations

Input ratings are shown in BTU per hour and are

certiﬁed without deration for elevations up to

4,500 feet (1,370m) above sea level.

For elevations above 4,500 feet (1,370m) in USA,

installations must be in accordance with the

current ANSI Z223.1/NFPA 54 and/or local codes

having jurisdiction.

In Canada, please consult provincial and/or local

authorities having jurisdiction for installations at

elevations above 4,500 feet (1,370m).

Gas Line Installation

When purging gas line the front glass

must be removed.

The gas pipeline can be brought in through the right

side of the appliance. Knockouts are provided at conve-

nient locations to allow for the gas pipe installation and

testing of any gas connection.

The gas line connection can be made with properly

tinned 3/8” copper tubing, 1/2” rigid pipe or an approved

ﬂex connector. Since some municipalities have addi-

tional local codes, it is always best to consult your local

authority and the CSA-B149.1 installation codes.

For USA installations consult the current National Fuel

Gas Code, ANSI Z223.1/NFPA 54.

3/4” (19 mm) Scribe

Moulding for use with

CFM Cabinets

DVB4136 Direct Vent Gas Fireplace

20012322

Always check for gas leaks with a mild

soap and water solution applied with a

brush no larger than 1” (25 mm). Never

apply soap and water solution with a spray

bottle. Do not use an open ﬂame for leak

testing.

The ﬁreplace valve must not be subjected

to any test pressures exceeding 1/2 psi.

Isolate or disconnect this or any other gas

appliance control from the gas line when

pressure testing.

The gas control is equipped with a captured screw type

pressure test point, therefore it is not necessary to pro-

vide a 1/8” test point up stream of the control.

When using copper or ﬂex connector use only approved

ﬁttings. Always provide a union when using black iron

pipe so that the gas line can be easily disconnected for

burner or fan servicing. (Fig. 6) See the gas speciﬁca-

tions for pressure details and ratings.

Remote ON/OFF Switch Installation

Do not wire the remote ON/OFF wall switch for this gas

appliance into a 120v power supply.

1. Thread wire through the electrical knockout located

on either side of the unit. Take care not to cut the

wire or insulation on metal edges. Ensure the wire is

secured and protected from possible damage. Run

one end of the gas control valve and the other end to

the conveniently located wall switch.

2. Attach the wire to the ON/OFF switch and install

switch into receptacle box. Attach cover plate to

switch.

3. Connect wiring to gas valve. (Fig. 7)

FP297A

INSTA VENT FREE

UVHB26 GAS SUPPLY

7/1/98

1/2” Gas Supply

1/2” NPT x 3/8” Flare Shut-

off Valve

3/8” Flex Line

(from valve)

FP297a

Fig. 6 Typical gas supply installation.

TPTH TH

FP1218

Remote switch

wiring

8/02

Remote ON/OFF

Switch

FP1218

Fig. 7 Remote switch wiring diagram for R models.

Alternate Switch Location

The remote switch can be installed on either side of

the access door. Mount the switch to the switch bracket

provided. Screw the bracket on either side of the frame,

line up the screws with the prepunched holes. (Fig. 8)

FP1024

alternate

remote switch

location

1/27/00 djt

FP1024

Fig. 8 Alternate switch location.

EB-1 Electrical Box

The ﬁreplace, when installed, must be

electrically connected and grounded in

accordance with local codes or, in the ab-

sence of local codes, with the current CSA

C22.1 Canadian Electrical Code.

For USA installations, follow the local

codes and the national Electrical Code

ANSI/NFPA No. 70.

It is strongly suggested that the wiring of

the EB-1 Electrical Junction Box be carried

out by a licensed electrician.

Ensure that the power to the supply line

has been disconnected before commenc-

ing this procedure.

The EB-1 electrical junction box has been

supplied standard on the DV360/580 models to allow

for the easy installation of an optional fan kit.

To connect the EB-1 box to the house electrical supply,

follow the steps below.

1. Unscrew the retaining screw from the EB-1 base

plate (Fig. 9) and remove the EB-1 assembly from

the ﬁreplace.

2. Remove the front cover of the EB-1 box.

3. Remove the plug socket assembly from the EB-1

box.

4. Feed the supply line in from the outside through the

cable clamp. (Fig. 9)

5. Connect black wire of the power supply line to the

brass screw (polarized) of the socket assembly.

6. Connect the white wire of the power line to the

chrome screw of the socket assembly.

DVB4136 Direct Vent Gas Fireplace

20012322

FP580

INSTA VENT FREE

EB1 JUNCTION BOX

11/18/97

OUTSIDE

Electrical Box

FRONT OF UNIT

INSIDE

FRONT OF UNIT

FP580

Fig. 9 EB-1 receptacle.

7. Connect the ground wire of the supply line to the

green screw of the socket assembly.

8. Reﬁt the socket assembly back into the electrical

box and replace the cover plate. Secure the cable

with the clamp on the outside of the unit to prevent

strain on the connections.

9. The EB-1 electrical junction box is now ready to sup-

ply power to the FK12 or FK24 fan kits if ﬁtted.

Autres manuels pour DVB4136

Table des matières

Autres manuels Majestic fireplaces Cheminée intérieure

Majestic fireplaces

Majestic fireplaces Cabinets Classic Series Manuel utilisateur

Majestic fireplaces

Majestic fireplaces WMC36 WMC42 Manuel utilisateur

Majestic fireplaces

Majestic fireplaces Royalton BC36 Instructions de montage

Majestic fireplaces

Majestic fireplaces 33LDVR Instructions de montage

Majestic fireplaces

Majestic fireplaces Royal Collection WMC36 Manuel utilisateur

Majestic fireplaces

Majestic fireplaces MO18 Manuel utilisateur

Majestic fireplaces

Majestic fireplaces LDVR1 Instructions de montage

Majestic fireplaces

Majestic fireplaces FireStage UVSRC36A Instructions de montage

Majestic fireplaces

Majestic fireplaces SHR42 Instructions de montage

Majestic fireplaces

Majestic fireplaces DVB4136 Instructions de montage

Majestic fireplaces

Majestic fireplaces Riverview RDV4136RN Manuel utilisateur

Majestic fireplaces

Majestic fireplaces MDVI30IL Manuel utilisateur

Majestic fireplaces

Majestic fireplaces 360DVS2 RN Instructions de montage

Majestic fireplaces

Majestic fireplaces Royal Collection WMC36 Instructions de montage

Majestic fireplaces

Majestic fireplaces WM36SX Manuel utilisateur

Majestic fireplaces

Majestic fireplaces FireStage UV36 Instructions de montage

Majestic fireplaces

Majestic fireplaces Arch Screen Door Kit GABS4S0 Manuel utilisateur

Majestic fireplaces

Majestic fireplaces Royalton BC36 Instructions de montage

Majestic fireplaces

Majestic fireplaces SH48 Manuel utilisateur

Majestic fireplaces

Majestic fireplaces NVCR36R Series Manuel utilisateur

Majestic fireplaces

Majestic fireplaces NVBC42 Instructions de montage

Majestic fireplaces

Majestic fireplaces VF Collection UVS36 Manuel utilisateur

Majestic fireplaces

Majestic fireplaces R36A Manuel utilisateur

Majestic fireplaces

Majestic fireplaces FireStage UVSRC36A Instructions de montage

Manuels Cheminée intérieure populaires d'autres marques

Brigantia

Brigantia 35-DVRS31N-2 Manuel du propriétaire

Nordpeis

Nordpeis Bergen Manuel utilisateur

Superior

Superior BCT2536TMN Manuel utilisateur

Quadra-Fire

Quadra-Fire 5100I-GD-B Manuel utilisateur

Renaissance

Renaissance RUMFORD 1000 Manuel utilisateur

Lacunza

Lacunza IV-800 Manuel utilisateur

Baxi

Baxi 940 Instructions d'utilisation

Dru

Dru Maestro 60/2 Tall RCH Manuel utilisateur

Diamond Fireglass

Diamond Fireglass SS-O22 Manuel utilisateur

HearthStone

HearthStone Windsor Bay 8830 Manuel de programmation

Napoleon

Napoleon ASCENT B42 Manuel utilisateur

Enviro

Enviro E33GI Manuel utilisateur

Smeg

Smeg L30 FABE Instructions de montage

KEDDY

KEDDY K700 Manuel utilisateur

Godin

Godin 3451 Manuel utilisateur

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Manuel utilisateur

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 Manuel utilisateur

Desa

Desa CCFPDFT Manuel d'utilisation