Majestic Appliances 17-1021 Manuel utilisateur

Installation Instruction

PN 17-1021

WQP8-9122

MAJESTIC APPLIANCES DIV OF MSI

3201 Northwest Lower River Road, #9, Vancouver, WA 98660 USA

WWW.majesticappliances.com

READ CAREFULLY AND KEEP THESE INSTRUCTIONS.

BEFORE INSTALLATION

Read these instructions completely and carefully.

IMPORTANT

Observe all governing codes and ordinances.

Note to Installer

Be sure to leave these instructions for the consumers

and local inspectors use.

Note to Consumer

Keep these instructions with your Owners Manual for

future reference.

Skill level

Installation of this dishwashers require basic mechanical

and electrical skills. Improper installation can result in

product failure which is not covered under the Product

Warrant.

IMPORTANT

The dishwasher must be installed to allow for future

removal from the enclosure ifservice is required.

Before You Begin--Examine the dishwasher carefully,

if the product is damaged, you should immediately contact

your dealer.

FOR YOUR SAFETY

Read carefully all WARNINGS and CAUTIONS in this

instructions which will guarantee your safety.

CONTENTS

Material You Will eed 1

Tools 1

Unit Dimensions 2

Prepare the Location 2

Conner Installation 2

Ways of Drain Connections 2

Prepare Electrical Wiring 3

Electrical Requirement. 3

Prepare Water Line 4

Adjust Door Balance 4

Remove Toekick 4

Install Power Cord 5

Position Water Line and House Wiring 5

Insert Drain Hose through Cabinet

and Connect Water Line 5

Slide Dishwasher into Cabinet 5

Level Dishwasher, Secure to Cabinet. .' 6

Connect Drain Hose 7

Connect Power Supply 8

Pre- Test Check List 8

Dishwasher Wet Test 9

Replace Toekick 9

Literature

........................................ 9

r---------------------------------------------------------------------------------------------------------r---

Installation Preparation

MATERIALS YOU WILL NEED

2 #8 flat head wood screws, 5/8" long to secure

dishwasher to underside of countertop or to side of

cabinetry (Taped to top or side of dishwasher)

Side and top trim pieces

Ferrule, compression nut and 90

Elbow (3/8"NPT

external thread on one end, opposite end sized to fit

water supply)

Thread seal tape

UL Listed wire nuts

Materials For New Installations Only:

Air gap for drain hose, if req uired

Waste tee for house plumbing, if applicable

Electrical cable or power cord, if applicable

Screw type Hose clamps

Strain relief for electrical connection.

Hand shut-off valve (recommended)

Water line 3/8" min. copper or 112" min. Plastic

(plastic must be tested for temperature and pressure)

Coupler for extending drain line, if applicable

Wood Screws Trim Pieces Air Gap

MID)

@])eiU)

Hand Thread

Waste Tee Shut-off Seal Tape Wire Nuts

Valve

Elbow, Ferrule

and Compression nut Electrical Cable

(or Power cord) Hot Water Line

Screw Tape Strain Relief Coupler

Hose Clamps

TOOLS

Head screwdriver

5/16" and" nutdriver

6" Adjustable wrench

Level

Carpenters square

Measuring tape

Safety glasses

Flashlight

Bucket to catch water when flushing the line

15/16" socket (optional for skid removal)

Gloves

Tubing cutter

Drill and approprivate bits

Hole saw set

Level

Carpenters

Square

Hole Saw Sei Flashlight

Tubing Cutter

Safety Glasses

Gloves

6" Adj ustable

Wrench

Measuring Tape

Drilland Bits

Installation Preparation

UNIT DIMENSIONS WAYS OF DRAIN CONNECTIONS

23"

33"-35'

Figure 1

DEPTH: 23"(5S0mm)

WIDTH: lS"(450mm)

HEIGHT: 33"-35"

(S40-S90mm)

PREPARE THE LOCATION

The dishwasher should be installed in the kitchen near

the sink, which will easier connect the water and drain

suppJy lines.

A build-in dishwasher must be enclosed on the top, both

sides and the back.

33"35-112"

Underside of

Countertop to Flo r

,/------'-----i

Min.

IS"

Floor must be Even

With Room Floor

Figure 2

DEPTH: 24"(610mm)

WIDTH: lS"(460mm)

HEIGHT: 33"-35-1I2"(S40-900mm)

CONNER INSTALLATION

If you install the dishwasher

into a corner, allow 2" min.

Clearance between dishwasher

and adjacent cabinet, wall or

other appliances. Allow 22"

min. Clearance from the front

of the dishwasher for door

opening.

Minimum Clearance

I/r.--------- II ~

Figure 3

The type of drain installation depends on the following

question.

Air gap is required by the local codes and ordinances

Waste tee less than 18" minimum above the floor.

Ifboth answers are yes, choose A and B. Or you should

choose C and D ..

A) air gap with waste tee

r-0

Figure 4

B) air gap with disposer

r-0

Figure 5

Figure 6

D) disposer ~

Figure 7

Installation Preparation

PREPARE ELECTRICAL WIRING

WARNING

FORPERSONALSAFET~

Remove house fuse or open circuit breaker before beginning installation. Do not use an extension cord or adapter

plug with this appliance.

GROUNDING INSTRUCTIONS--Power Cord Models

This appliance must be grounded. In the event of a malfunction or breakdown, grounding will reduce the risk of

electric shock by providing a path ofleast resistance for electric current. This appliance is equipped with a cord

having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate

outlet that is installed in an accordance with all local codes and ordinances.

AWARNING

Improper connection of the equipment-grounding conductor can result in a risk of electric shock .Check with a qualified

electrician or service representative if you are in doubt wether the appliance is properly grounded. Do you modify the plug

provided with the appliance; Hit will not fit the outlet, have a proper outlet installed by a qualified electrician.

GROUNDING INSTRUCTIONS--Cable Direct

This appliance must be connected to a grounded metal, permanent wiring system ,or an equipment-grounding

conductor must be run with the circuit conductors and connected to the equipment-grounding terminal or lead on

appliance.

ELECTRICAL REQUIREMENT

This dishwasher is designed for operation on an adequately wired individual 120VAC, 60HZ, and connected to an

individual, properly grounded branch circuit, protected by a 15 or 20 amp circuit breaker or time-delay fuse.

the electric supply provided does not meet the above specifications, it is recommended that a licensed electrician

install an approved outlet.

Your dishwasher circuit should not be used for any other appliance while the dishwasher is in operation as the

dishwasher requires the full capacity ofthe circuit.

the wall socket you plug the dishwasher's power cord into is controlled by a switch, turn off the switch before

installation.

1 The power-supply socket for the appliance shall be

installed in a cabinet or on a wall adjacent to the

undercounter space in which the appliance is to be

installed.

2 There shall be an opening through the partition

between the compartments specified in 1 that is .

large enough for the attachment plug to pass through.

The longest dimension of the opening shall not be

more than 38mm.

3 The edges of the opening specified in 2 shall, ifthe

partition is wood, be smooth and rounded, or, if the

partition is metal, be covered with an edge protector

provided for this purpose by the manufacturer; and

Figure 8

4 Care shall be exercised, when the appliance is

installed or removed, to reduce the likelihood of

damage to the power-supply cord.

ELECTRICAL CONNECTION

Electrical connection is on the right front of dishwasher.

For cable direct connections the cable must be routed as shown. Cable must extend a minimum of24" from the rear

wall. For power cord connections, install a 3-prong grounding type receptacle in the sink cabinet rear wall, 6" min.

Or 16" max. From the opening, 6" to 16" above the floor.

Installation Instructions

PREPARE WATER LINE

The line may enter from either side, rear or floor within

the shaded area.

The line may pass through the same hole as the eledtrical

cable and drain hose. Or, cut an additional. Ifpower cord

with cord with plug is used, water line must not pass

through power cord hole.

/ I I '

----- 1/ //

/f' / ,

I ,

=====£t

~:~n"

o;~:

5"j- 4~"+5'~: ,4" ",

Shut-off. Hole

-I 1-- -,

~ Valve,.} ( -------- ~

HODI====c::r_-_-_, I

H I I

:: 2

----t------

From

Cabine

19" From Wall

2" From Floor

Cabinet Face--

Figure 9

WATER LINE CONNECTION

Note to Consumer

Midea dishwasher could use both hot water and cold wate .

*Turn off the water supply.

*We suggest you installing a hand shut-off valve in an

accessible location, such as under the sink.

*Water connection is on the left side of the dishwasher.

Install the hot water inlet line, using no less than 3/8"

O.D. Copper tubing. Route the line as shown and extend

forward at least 19" from rear wall.

*Flush water line to clean out debris.

*The water pressure must be O.04~1 Mpa.

ADJUST DOOR BALANCE

Our company have adjusted door balance well. If you

do not satisfy the tension of spring or after installing

the door panel, you may adjust the spring

*if door drops open when released, increase spring

tension. If door closes when released, decrease tension.

Increase

Spring

;- t~:::~~.

Spring

'Ienston

Figure 10

ADJUSTMENT

If door does not open easily or fall too quickly, you

should adjust the tension of door spring. Pull out bolt

and insert it into lower or higher hole, the spring

tension will be increase or decrease. If you do not

satisfy the tension still, repeat the process.

REMOVE TOEKICK

Remove the toe kick.

Figure 11

Installation Instructions

INSTALL POWER CORD

Skip this step if dishwasher will be direct wired or has

a factory installed power cord.

The power cord and connections must comply with

the National Electrical Code, Section 422 and/or

local codes and ordinances.

Figure 12

A C

Remove Insert Power

Junction Box Cord Wires Thr

Cover Strain Relief

{D-~"d_::::~---i

Check That White, Black and

Green Dishwasher Wires Are Threaded

Thru Small Hole in Bracket

UseULListed

Wire Nuts

*Connect incoming power cord white (or ribbed) to

dishwasher white, black (or smooth) to black and

Ground to dishwasher green wire. Use UL listed wire

nuts of appropriate size.

*Replace j unction box cover. Be sure wires are not

pinched under the cover.

POSITION WATER LINE

AND HOUSE WIRING

Position water supply line and house wiring on the

floor ofthe opening to avoid interference with base of

dishwasher and components under dishwasher.

Figure 13

SLIDE DISHWASHER INTO CABINET

INSERT DRAIN HOSE AND

CONNECT WATER LINE

Upright the dishwasher and position in the front of

opening. Insert drain hose into cabinet wall hole.

If a power cord is used, guide the end through a

separate hole.

Figure 14

Connect the water line of dishwasher into user water line.

DO NOT PUSH AGAINST FRONT PANEL WITH KNEES.

DAMAGE WILL OCCUR.

Slide dishwasher into the opening a few inches at a time.

Figure 15

As you proceed, pull the drain hose through the opening

under the sink. Stop pushing when the dishwasher is a few

inches forward of adjacent cabinetry.

Make sure drain hose is not kinked under the dishwasher

and there is no interference with the water line and wiring

or any other component.

Installation Instructions

LEVEL DISHWASHER

IMPORTANT-- Dishwasher must be level for proper dish

rack operation and wash performance.

Place level on door and rack track inside the tub as

shown to check that the dishwasher is level.

Level the dishwasher by adjusting the four leveling.

*If adjustment to the right rear leveling leg is required,

loosen junction box bracket screw and rotate bracket

clockwise.

Check

Level

Front

to Back

t~k~~~~~~

Check Level

'==..JT:c:-- \----j

\,rI

Side To Side

Turn Legs

to Adjust

Figure 16

Figure 15

POSITION DISHWASHER, SECURE TO CABINET

The dishwasher must be secured to the countertop or

the cabinet sides. When countertops are made of wood

use Method 1. Some models are supplied with side

mounting brackets for use when countertops are granite

or other materials that will not accept screws. Use

Method 2 to secure dishwasher at the sides.

Method 1

Secure Dishwasher To Wood countertop

Position dishwasher so that the door lines up with the

front face of adjacent cabinet.

Brackets Wood Countertop

Figure 18

j j

~~~r

: : 3/4"

e e

Figure 17

IMPORTANT--Check to be sure the dishwasher is center

ed in the opening and there is no interference with

adjacent cabinets when opening or closing the door

top with the 2 Phillips screws provided ..

*Position dishwasher so that the door lines up with the

front face of adjacent cabinet.

IMPORTANT:

Check to be sure the dishwasher is centered in the

opening and there is no interference with adjacent

cabinets when opening or closing the door

Installation Instructions

CONNECT WATER SUPPLY

IMPORTANT-- Check to be sure that dishwasher does.not rub or

Thread Seal Tape

contact the fill hose or water supply line.

*Wrap 90· Elbow with thread seal tape.

Install a 90· elbow onto the water valve.

*Do not over tighten 90° elbow, water valve bracket could bend

or water valve fitting could break.

*Position the end of the elbow to face the left.

*Connect water supply line to 90° elbow.

Ifwater supply line could not be connected to 90° elbow directly,

with a ferrule and compression nut.

*Slide compression nut, then ferrule over end of water line.

*Insert water line into 90° elbow.

*Slide ferrule against elbow and secure with compression nut. Figure 19

Elbow

Installation Instructions

CONNECT DRAIN LINE

FOLLOW ALL LOCAL CODES AND ORDINANCES.

If a longer drain hose is required, add up to 42

oflength for a total of 10 ft. length to the factory installed

hose. Use 5/8" or 7/8" inside diameter hose and a coupler to connect the two hose ends. Secure the

connection with hose clamps.

-=1JCQ~P

Hose Clamp Figure 20

Secure the drain hose to the air gap, waste tee or disposer with clamps.

NOTE: TOTAL DRAIN HOSE LENGTH MUST NOT EXCEED 10 FEET FOR PROPER DRAIN OPERATION.

Connect drain line to air gap, waste tee or disposer using either previously determined method.

Method

--Air gap with waste tee of disposer

Figure 21--air gap with waste tee Figure 22--air gap with disposer

Figure 24--disposer

Figure 23--waste tee

.- Remove

-4J

Hopper

Plug

IMPORTANT

If drain plug of disposer or waste tee has not been

removed, the dishwasher will not drain. Disposer Waste tee

Figure 25

Ce manuel convient aux modèles suivants

Autres manuels Majestic Appliances Lave-vaisselle

Majestic Appliances

Majestic Appliances WQP8-9122 Manuel utilisateur

Manuels Lave-vaisselle populaires d'autres marques

Electrolux

Electrolux ESI5211LOX Manuel utilisateur

KitchenAid

KitchenAid KUDB230B Manuel utilisateur

Brandt

Brandt BDJ424DB Manuel utilisateur

Asko

Asko DSD767UXXL.AU Manuel utilisateur

Beko

Beko DFN26210W Manuel utilisateur

NEFF

NEFF S153ITX00E Fiche technique

Midea

Midea SV 4.45 wi Manuel utilisateur

LG LDF7932 Manuel utilisateur

Gorenje

Gorenje GV63214 Manuel utilisateur

Hotpoint

Hotpoint HDA1100ZWH Manuel de service

Blomberg

Blomberg LDFN2240W Manuel utilisateur

AEG

AEG FFB83836PM Manuel utilisateur

Cylinda

Cylinda DM3220RFD Manuel utilisateur

Atag

Atag DW8214MB Manuel utilisateur

GE GLD8000 Series Manuel utilisateur

Siemens

Siemens SN23HI02KE Fiche technique

Omega

Omega ODW717X Manuel utilisateur

BORETTI

BORETTI BVW-683 Manuel utilisateur