Macsense MPC-200 Manuel utilisateur
1
User’s Manual
Fast Ethernet CardBus
(MPC-200)
R
acsense
Table of Contents
Chapter 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Network Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Driver support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Physical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Installing the Fast Ethernet CardBus Card . . . . . . . . . . . . . . . . . . . . .2
Chapter 2 Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Installing the Fast Ethernet CardBus Card . . . . . . . . . . . . . . . . . . . . .3
LED Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Readme file . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Chapter 3 Driver Installation for Mac OS . . . . . . . . . . . . . . . . . . . . . .5
System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Software Installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
AppleTalk Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
TCP/IP Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Ejecting the Fast Ethernet CardBus Card . . . . . . . . . . . . . . . . . . . . . .7
Appendix A Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Appendix B Assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
RJ-45 Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
i
Chapter 1 Introduction
This manual describes how to operate the Fast Ethernet CardBus Card. The Fast
Ethernet LAN PC Card is a Credit-card sized Ethernet Card which works with any comput-
er, notebook, sub-notebook or Macintosh PowerBook G3 series, or Card Reader that sup-
ports CardBus slots.
CardBus is a function and performance extension of the PC Card (PCMCIA) stan-
dards. The CardBus interface is a 32-bit wide and Bus-mastering allowable device. It
enhanced the overall system throughput.
This Fast Ethernet CardBus Card could be connected to either 100Mbps Fast Ethernet
or 10Mbps Ethernet network.
¥ For operating in a 100Mbps (100BASE-TX) Fast Ethernet network, a Category 5
unshielded twisted pair (UTP) cable or Category 1 shielded twisted pair (STP) cable
should be used.
¥ For operating in a 10Mbps (10BASE-T) Ethernet network, a Category 3,4, or 5
(UTP) cable or Category 1 shielded twisted pair (STP) cable could be used.
Features
¥ CardBus form factor for CardBus equipped portable PCs
¥ IEEE 802.3 for 10BASE-T and IEEE 802.3u for 100BASE-TX compliant
¥ Automatically negotiates 10Mbps or 100Mbps connection speeds, depending on
speed of the network
¥ Provides full-duplex to enhance throughput
¥ Offers high performance 100Mbps networking via 32-bit, PCI CardBus slot
¥ Complies to PC Card 1995 CardBus standards
¥ Switch-less design and software configurarble card setting
¥ 68-pin connector for attachment to PC's CardBus slot, and 15-pin flat connector to
media coupler
¥ 3.3V low power consumption
¥ LEDs monitoring indicators
Network Interface
¥ RJ-45 to connect with 10BASE-T hub, 100BASE-TX Hub, or Switch Hub
Physical Characteristics
¥ Standard Conformance: IEEE 802.3 for 10BASE-T
IEEE 802.3u for 100BASE-TX
¥ Host Interface: PC Card 95 CardBus Standard
¥ Ethernet Data Speed: 10Mbps and 100Mbps (Auto-Negotiation)
Introduction
1
¥ Bus Width: 32 bits
¥ Power: 3.3 V
¥ Temperature: 0ûC~60ûC/ 32ûF~140ûF (Std. Operating)
¥ Humidity: 10% to 90%
¥ Distance: 100m from Hub to Node
¥ Dimensions: 86mm x 54mm x 5 mm
Installing the Fast Ethernet CardBus Card
You will be installing the Fast Ethernet CardBus Card in your computer. If you are
having trouble locating the slot, refer to the user's manual of your computer or consult the
manufacture of your computer.
Gently slide the PC Card into the CardBus PC Card slot. Make sure the Card is firmly
seated in the socket and you are ready to setup and install the network drivers.
For a connection to a Fast Ethernet network, use a Category 5 unshielded twisted pair
(UTP-5) or Category 1 shielded twisted pair (STP-1) cable with a RJ-45 connector to
connect with a 100Mbps port of hub or switch.
For a connection to a 10BASE-T Ethernet network, use a Category 3,4 or 5 (UTP) or
(STP) 1 cable with a RJ-45 connector to connect with a 10Mbps port of a hub or switch.
Introduction
2
Chapter 2 Getting Started
Installing the Fast Ethernet CardBus Card
You will be installing the Fast Ethernet CardBus Card in CardBus slot of your computer.
If you have trouble locating the slot, please refer to your computer's user manual or
consult the dealer of your computer.
Follow the procedure below to install the Fast Ethernet CardBus Card.
1. Turn off the host computer.
2. With the card's 68 pin connector facing the PCMCIA CardBus slot, gently slide the
PC Card into the CardBus slot. Make sure the card is firmly seated in the socket
3. Plug the Ethernet adapter cable to the 15-pin connector on the Fast Ethernet
CardBus Card as in the following figure below.
4. Connect your Ethernet adapter cable to the network using a RJ-45 cable.
5. Power on your notebook computer.
6. Now you are ready to install your communication software as described in the
following chapters.
Getting Started
3
LED Indicators
¥ 100 LED: This LED is used to indicate the Ethernet speed:
The green light
indicates a connection with a 100BASE-TX Fast Ethernet network
.
¥ Link/Act LED: This LED is used to indicate the network activity. It is blinking when
the PC Card is transmitting or receiving packets from network.
It is
also lit when indicating a Link to a network.
README
There is one file named Readme on driver diskette which provides the information
about this Driver Diskette's contents and installation guide. This file is located in the root
directory of the diskette.
Getting Started
4
Chapter 3 Driver Installation for Mac OS
System Requirements
¥ Mac OS version 8.1 or above.
¥ Macintosh G3 PowerBook Series.
¥ Card and Socket Service 3.0.
¥ Open Transport 1.3 or above
Installation
Before your computer system can recognize your Fast Ethernet CardBus Card, it is
necessary to run some software to enable it. This section gives a brief overview of the
installation process.
Software Installation
1. Make sure that the system extensions are left on before installing the driver.
2. Insert the FastEther CardBus driver diskette into the floppy drive.
3. Double-click the Installer icon. The Easy Install dialog box then appears
Chapter 3 Driver Installation for Mac OS
5
4. Click the Install button. The Installer will install the appropriate driver to your com-
puter.
5. Click the Restart button when installation is completed.
AppleTalk Setup
¥ Open the AppleTalk control panel
¥ Select FastEther Card from the pop-up menu.
Optional: The Current Zone pop-up menu will be active if zones are available.
Chapter 3 Driver Installation for Mac OS
6
¥ Close the control panel when you have finished.
¥ To confirm the change of network connections, click OK.
TCP/IP Setup
¥ Open the TCP/IP control panel.
¥ Select FastEther Card from the pop-up menu.
.
¥ Set up TCP/IP configuration according to the situation of your network environment.
¥ Close the control panel when you have finished.
¥ To confirm the change of network connections, click OK.
Ejecting the FastEther Card
¥ Open the AppleTalk control panel
¥ Select an AppleTalk connection other than FastEther Card, (e.g. IRTalk, LocalTalk,
Printer Port, or Modem Port).
¥ Close the control panel and wait for a few seconds.
Chapter 3 Driver Installation for Mac OS
7
¥ Drag the FastEther Card icon that appears on the desktop to the Trash.
¥ Then the FastEther Card will eject automatically.
Chapter 3 Driver Installation for Mac OS
8
Autres manuels pour MPC-200
1
Table des matières
Autres manuels Macsense Carte réseau
Manuels Carte réseau populaires d'autres marques
3Com
3Com EtherLink 3C509B Manuel utilisateur
TRENDnet
TRENDnet TEG-PCITX Manuel utilisateur
Cisco
Cisco MC16E Manuel utilisateur
Delta Electronics
Delta Electronics Braking Modules VFDB Series Manuel utilisateur
TwinMOS
TwinMOS Booming Manuel utilisateur
Dialogic
Dialogic Media Board DM/V1200BTEPEQ Manuel utilisateur
Buffalo
Buffalo AirStation WLI-PCM-L11GP Manuel utilisateur
National Instruments
National Instruments NI 9234 Manuel utilisateur
Hama
Hama 49276 Manuel utilisateur
Linksys
Linksys WCF54G - Wireless-G Compact Flash Card Manuel d'utilisation
Compaq
Compaq Wireless LAN 100 Manuel utilisateur
Bose
Bose PowerMatch Dante Manuel utilisateur