Macab DT-2200 Manuel utilisateur
QPSK
DT-2200
ENGLISH 49–64
MANUAL
ENG-1 • 011001 • 01042
01042-4 DT-2200 ENG-1.p65 2001-09-26, 08:4649
MANUAL
DT-2200
50
DT-2200 .......................................... 50
Front ............................................... 51
Back ............................................... 51
Smart card ...................................... 52
Programming unit ............................ 53
Self test ........................................... 53
Menu information ............................. 54
Table of contents
DT-2200
A versatile digital receiver with a guaranteed future
One of the advantages with DT-2200 is the flexible design. The receiver is equipped with a
Common Interface and a card reader (embedded), for adding an access-system. This may for
example be Viaccess, Conax, Cryptoworks or Irdeto. Another appreciated function is VBI-text,
which allows text TV to be sent over the building net automatically. A future advantage is an
upgradeable software package. It is easy to download new functions in coming from satellite or a PC.
In order to increase reliability, all components have been selected with the greatest attention and
each unit is individually tested before delivery.
Important! Digital signals put great demands on the installation’s LNB. Older microwave heads
often exhibit an unsatisfactory phase noise value, which may reveal itself as a frozen picture or text.
Therefore, always upgrade to new microwave heads when adding digital receivers.
Error log .......................................... 54
Menu overview ................................ 55
Programming ............................. 56–58
Information “menu” ..................... 59–61
PID setting ....................................... 61
Technical data ................................. 62
Connectors ...................................... 63
01042-4 DT-2200 ENG-1.p65 2001-09-26, 08:4650
MANUAL
DT-2200
51
Front
1. Reset-button
2. Common interface
3. Fan*
4. Card reader
5. Display
6. LED ”Alarm (red)”
- ”QPSK lock (yellow)”
- ”On indication (green)”
7. Button ”Left/Right”
- ”Up/Down”
8. Button ”Menu”
- ”Enter”
*
The fan is temperature regulated and starts at 30-35
24567831
Back
1. Mains voltage 180–260VAC
2. Balanced audio output, right (XLR)
3. Balanced audio output, left (XLR)
4. Alarm contact jack
5. Aux. COM2-port*
6. Data COM1 for upgrading software (PC).
7. Audio jack right/left (RCA)
8. SVHS jack
9. Video out (1+2)
10. Transport current output Parallel LVDS
11. LNB in 13/18V DC, 350mA, 22kHz
12. IF out
*Used for future functions (optional)
123456789101112
01042-4 DT-2200 ENG-1.p65 2001-09-26, 08:4651
MANUAL
DT-2200
52
Smart card
SMARTCARD
CA-MODULE
DVB/CI-SOCKET
CARD READER
CA MODULE
A CA module connector is located at the front.This is used for channels which are coded in different
transmission systems. Conax, Viaccess, Cryptoworks, Nagravision and Irdeto are common coding
systems which can all be used with the DT-2200.
Insert the programme card into the CA module. The gold-coloured interface on the card must point
towards the front of the module. Insert the module with the programme card into the front of
DT-2200 in the DVB/CI socket. In most cases, one side of the module is marked and this side
should face the marking for the DVB/CI socket on the DT-2200.
CARD READER
The right card reader is used for a downloaded (embedded) coding system, i.e. Conax and Viaccess.
The card should be inserted with the gold coloured contact surface turned downwards – inwards.
If the programme card is not updated, the following message will appear on theTV screen: “No subscription”
Important:
• When receiving free channels, “Free To Air”, the CA module must not be connected.
• CA modules for different coding systems can be obtained from the programme companies.
• OSD information on the programme card may differ, depending on the coding system being used.
• When the CAM should be removed the button for the DVB/CI socket should be used.
01042-4 DT-2200 ENG-1.p65 2001-09-26, 08:4652
MANUAL
DT-2200
53
Programming unit
Programming is done using the Menu-Enter-Up-Down-Left-Right buttons in conjunction with
the display or the TV screen. Program the QPSK-receiver’s IF, polarity, 22kHz, symbol rate, FEC,
sound and sub-text language. Each satellite receiver is programmed individually.
In order to program the unit, the digital receiver must be powered up (the green LED is lit up)
and a correct satellite signal must be connected.
BUTTONS
Up - use this button to select settings on menus.
Left - use this button to select numbers. To change the channel.
Right - use this button to select numbers. To select options on the Info menu.
Down - use this button to select settings on menus.
MENU - use this button to activate the menu. De-activate the Info menu.
ENTER - save and move to the next menu option.
Please refer to the menu tree on page 55.
One of the features of the DT-2200 is the self test. When
it’s started various parts will be tested and the results will be
shown on theTV screen.
Press and hold the Menu button when powering up the
receiver.
•PASS=OK
•FAIL=NOT OK
SelfTest
CA (Cimax) at 0x80 Pass
VP310 (QPSK) at 0x1c Pass
Satellite Tuner at 0xc2 Pass
Serial E2 at 0xa0 Pass
Audio DAC at 0x82 Pass
Video DAC at 0x54 Pass
Self test
01042-4 DT-2200 ENG-1.p65 2001-09-26, 08:4653
MANUAL
DT-2200
54
Displays the error log number.
Displays the cause of the error, see below.
Error 01 is displayed with date and time according to the TV-channel
information.
Display how many secundes after the Reset-button is used or start
(power up) som felet uppstod.
002:03
XXXXXXXX
002:03
XXXXXXXX
002:03
00000000
Remark: When the Cam is removed the receiver make a reset every 60
sec and the log file get entries until the CAM is connected.
Message _ _
01 = Power up –after manual or automatic reset and power up.
02 = QPSK loss –when the receiver lost the signal.
03 = QPSK lock –when the receiver find and lock the signal.
04 = Video stop –if the program card have no access or the video signal is lost.
05 = Audio stop –if the audio disappeares for any reasons.
Error log
Menu information
DT2200 02.10 003:00:15:46
MAIN MENU
Enter Trans
Freq 1528
Vid 0200 Aud 028a Pcr 0200 TTX 0240
Signal Level: 13.0dB 0.000000÷00
Video info: 3.080Mbps 704x576
Audio info: 48.000kHz
Error Log Contains 0 errors
A
B
C
D
E
A: Model –Software version –Time after reset
B: Selected IF frequency
C: PID adjusting, see page 61
D: Signalnivå= Eb/No BER = indicate 0 when OK
E: Displays the reasons for error see below
Press the MENU button and the menu will
appear on the TV screen. In this menu
information about the receiver will be found.
01042-4 DT-2200 ENG-1.p65 2001-09-26, 08:4654
MANUAL
DT-2200
55
Menu overview
PID
VPID - video PID
APID - audio PID
PCRPID - program clock reference PID
TextPID - text-TV PID
BUTTONS
Up - use this button to select settings on menus.
Left - use this button to select numbers. To change the channel.
Right - use this button to select numbers. To select options on the Info menu.
Down - use this button to select settings on menus.
MENU - use this button to activate the menu. De-activate the Info menu.
NEXT - save and move to the next menu option.
16/9 A
A
OSD Subt
trans Subt
pos
For Information press the Right button
Once Twice 3 times 4 times 5 times 6 times 7 times 8 times
PROGRAMMING
1) Press Menu button
2) Select IF frequency
3) Välj polarisation
4) Välj 22kHz
5) Select symbol rate
6) Select FEC
7) Select language (audio)
8) Select language (subtitle)
9) Select 16/9 format
1
2
3
4
5
6
7
8
9
INFORMATION
1) Signal quality
2) Log file
3) Delete log file
4) CI control
5) OSD On/Off
6) Subtitle transparency
7) Subtitle position
8) Audio level
01042-4 DT-2200 ENG-1.p65 2001-09-26, 08:4655
MANUAL
DT-2200
56
All programming is done using the Menu-Enter-Up-Down-Left-Right
buttons and the DT-2200 display.
TRANSPONDER FREQUENCY “IF FREQUENCY”
MENU Press the Menu button.
Use the Up/Down buttons to specify a number.
Use the Left/Right buttons to move between the numbers.
ENTER Press the Enter button to save and move on to the next menu
option.
The value of the setting of frequency (If frequency) depends on the local
oscillator frequency (L.O.) on the microwave head (LNB).
The frequency of the satellite channel – L.O. frequency (LNB) =
Intermediate frequency (IF) which is to be set.
Example
A satellite channel with frequency 11 309 and LNB of L.O. 9 750.
MF = 11 309 –9 750 = 1559 is the frequency to be set.
POLARIZATION
Use the Up/Down buttons for selecting the desired polarity H/V.
ENTER Press the Enter button to save and jump to the next menu
selection.
22KHZ
Use the Up/Down buttons 22kHz (Choose On or Off ).
ENTER Press the Enter button to save and jump to the next menu
selection.
Programmering
ENTER TRANS
FREQ 1559
ENTER
POLARITY H
22KHZ
OFF
01042-4 DT-2200 ENG-1.p65 2001-09-26, 08:4656
MANUAL
DT-2200
57
SYMBOL RATE
Use the Up/Down buttons to specify a number.
Use the Left/Right buttons to move between the numbers.
ENTER Press the Enter button to save and move on to the next menu
option.
Hint! 00000 activates auto scanning of the symbol rate.
FEC
Use the Up/Down buttons to select required FEC.
Select Auto for automatic searching of FEC.
ENTER Press the Enter button to save and move on to the next menu
option.
LANGUAGE “sound”
Use the Up/Down buttons to select the required language.
ENTER Press the Enter button to save and move on to the next menu
option.
LANGUAGE “subtitles”
Use the Up/Down buttons to select the required language.
ENTER Press the Enter button to save and move on to the next menu
option.
Programming
ENTER SOUND
LANGUAGE SWE
ENTER SUBT
LANGUAGE SWE
ENTER TRANS
SYMBOL 24500
ENTER TRANS
FEC AUTO
16/9
On
16/9 ”TV-format”
Use the Up/Down buttons to select the 16/9 format. Off= 4/3
format.
ENTER Press the Enter button to save and move on to the next menu
option.
01042-4 DT-2200 ENG-1.p65 2001-09-26, 08:4657
MANUAL
DT-2200
58
SEARCHING FOR CHANNELS
After adjusting the settings for the required transponders, a channel
search will be carried out. A QPSK lid (yellow LED, constant light)
must be present in order to find any channels. If the alarm lights up (red
LED) the installation and settings must be checked.
ENTER Select YES and press the Enter button to start the channel search.
The display indicates that the search is in progress. After completion
a menu will appear displaying all channels which were found on
the transponder. Select NO to set the PID, see page 61.
Use the Up/Down buttons to select a required channel.
ENTER Press the Enter button and after a few seconds the channel will
be displayed on the TV screen.
Important: PIDs are only to be used when you have problems finding
a required channel.
CHANGING CHANNEL
Switching to another channel within the transponder is simply done by
using the buttons and the display on the front panel of the DT-2200.
Press the Left button.
Use the Up/Down buttons to select a channel.
ENTER Press the Enter button and after a few seconds the channel
will be displayed on the TV screen.
START TRANS
SCAN YES
SCANNING....
PLEASE WAIT
DISCOVERY
(VIDEO)
DISCOVERY
Programming
01042-4 DT-2200 ENG-1.p65 2001-09-26, 08:4658
Table des matières
Autres manuels Macab Récepteur
