Mac allister MSHP2800D-2 Manuel utilisateur
Electric Shredder
2800 W
ORIGINAL INSTRUCTIONS - MSHP2800D-2 V02 - 07-10-2019
MSHP2800D-2
EAN: 3663602627357
WARNING: Read the instructions before using the product!
MSHP2800D-2
EAN: 3663602627357
Original Instructions_MSHP2800D-2_EN_V1_20180330
WARNING: Read the instructions before using the product!
Electric Shredder
2800 W
2
MSHP2800D-2
Let’s
get started...
These instructions are for your safety. Please read through them
thoroughly before use and retain them for future reference.
Getting Started... 02
Safety information 03
Your product 13
Before you start 14
In more detail... 19
Product functions 20
Operation 23
Care and maintenance 27
Troubleshooting 29
Recycling and disposal 30
Guarantee 31
Technical specications 32
EC declaration of conformity 33
3
MSHP2800D-2 Safety information
Getting Started . . .
Safety warnings
WARNING! READ CAREFULLY BEFORE USE
KEEP FOR FUTURE REFERENCE
Training
1.
Read the instructions carefully. Be familiar with the controls
and the correct use of the machine.
2.
Never allow children, persons with reduced physical, sensory
or mental capabilities or lack of experience and knowledge or
people unfamiliar with these instructions to use the machine.
Local regulations can restrict the age of the operator.
3.
Keep in mind, that the operator or user is responsible for
accidents or hazards occurring to other people or their
property.
Preparation
4. Obtain ear protection and safety glasses. Wear them at all
times while operating the machine.
5.
While operating the machine always wear substantial
footwear and long trousers. Do not operate the machine
when barefoot or wearing open sandals. Avoid wearing
clothing that is loose tting or that has hanging cords or ties.
6. Operate the machine in a recommended position and only
on a rm, level surface.
7. Do not operate the machine on a paved or gravel surface
where ejected material could cause injury.
8.
Before using, always visually inspect to see, that the
shredding means bolts and other fasteners are secure,
the housing is undamaged and that guards and screens are
in place. Replace worn or damaged components in sets to
preserve balance. Replace damaged or unreadable labels.
4
MSHP2800D-2
Safety information
Getting Started . . .
9. Before use check the supply and extension cord for signs
of damage or aging. If the cord becomes damaged during
use, disconnect the cord from the supply immediately. DO
NOT TOUCH THE CORD BEFORE DISCONNECTING THE
SUPPLY. Do not use the machine if the cord is damaged
or worn.
10.
Never operate the machine while people, especially children,
or pets are nearby.
Operation
1. Before starting the machine, make certain that the feeding
chamber is empty.
2.
Keep your face and body away from the feed intake opening.
3.
Do not allow hands or any other part of the body or clothing
inside the feeding chamber, discharge chute, or near any
moving part.
4.
Keep proper balance and footing at all times. Do not
overreach. Never stand at a higher level than the base of
the machine when feeding material into it.
5. Always stand clear of the discharge zone when operating
this machine.
6.
When feeding material into the machine be extremely careful
that pieces of metal, rocks, bottles, cans or other foreign
objects are not included.
7. If the cutting mechanism strikes any foreignobjects or
if the machine should start making any unusual noise
or vibration, immediately shut off the power source and
allow the machine to stop. Disconnect the machine from
the supply and take the following steps before restarting
and operating the machine:
- inspect for damage;
- replace or repair any damaged parts;
- check for and tighten any loose parts.
5
MSHP2800D-2 Safety information
Getting Started . . .
8.
Do not allow processed material to build up in the discharge
zone; this may prevent proper discharge and can result in
kickback of material through the feed intake opening.
9.
If the machine becomes clogged, shut-off the power source
and disconnect the machine from supply before cleaning
debris.
10.
Never operate the machine with defective guards or shields,
or without safety devices, for example debris collector in
place.
11.
Keep the power source clean of debris and other
accumulations to prevent damage to the power source or
possible re.
12.
Do not transport this machine while the power source is
running.
13. Stop the machine, and remove plug from the socket.
Make sure that all moving parts have come to a complete
stop:
- whenever you leave the machine;
- before clearing blockages or unclogging chute;
- before checking, cleaning or working on the machine;
- if the machine starts to vibrate abnormally, for
immediately check.
14. Do not tilt the machine while the power source is running.
15.
Do not overreach and keep the balance at all times, always
be sure of the footing on slopes and walk, never run.
16. Do not touch moving hazardous parts before the machine
is disconnected from the mains and the moving hazardous
parts have come to a complete stop.
17. Keep extension cords away from moving hazardous parts
to avoid damages to the cords which can lead to contact
with live parts.
18.
Disconnect the machine from the mains, if the cord becomes
damaged or entangled during use.
6
MSHP2800D-2
Safety information
Getting Started . . .
Maintenance and storage
1.
When the machine is stopped for servicing, inspection,
or storage, or to change an accessory, shut off the power
source, disconnect the machine from the supply and make
sure that all moving parts are come to a complete stop.
Allow the machine to cool before making any inspections,
adjustments, etc. Maintain the machine with care and keep
it clean.
2.
Store the machine in a dry place out of the reach of children.
3. Always allow the machine to cool before storing.
4. When servicing the shredding means be aware that, even
though the power source is switched off due to the interlock
feature of the guard, the shredding means can still be moved.
5.
Replace worn or damaged parts for safety. Use only genuine
replacement parts and accessories.
6.
Never attempt to override the interlocked feature of the
guard.
Additional safety instructions for units with bagging
attachments
1.
Switch the product off before attaching or removing the
collection box.
Recommendation
1.
The machine should be supplied via a residual current
device (RCD) with a tripping current of not more than 30 mA.
2.
Avoid using the machine in bad weather conditions especially
when there is a risk of lightning.
7
MSHP2800D-2 Safety information
Getting Started . . .
Additional warnings
1.
This appliance must be earthed! Use only three core
extension cables with the earth wire connected. If an
extension cord is used, make sure the extension cord is
specically designed for outdoor use with earthing terminal
and not lighter than H07RN-F, 3x1.5mm² and max. 75m.
2.
Carry the product by the handle with the motor off. Handling
the product properly reduces the possibility of personal
injury.
3.
If the product starts to vibrate abnormally, check it
immediately. Excessive vibration can cause injury.
4. Always ensure the product is fully assembled before using
it. Never attempt to use an incomplete product or one tted
with an unauthorised modication.
5. Do not overload the product.
6.
Follow the maintenance and repair instructions for this
product. Never carry out any modications to the product.
Information about maintenance and repair is provided in
this user manual.
7. Only use replacement parts and accessories supplied and
recommended by the manufacturer. Using third-party parts
will immediately invalidate the guarantee!
8.
Do not leave the product working unattended and keep it
in a dry place out of children’s reach.
9.
Keep hands and feet away from the cutting means at all
times and especially when switching on the motor.
10.
Do not touch the cutting means before the product is
disconnected from the power supply and the cutting means
have come to a complete stop.
11.
Whilst using the product, ensure the cable does not become
trapped under the wheels or feet.
8
MSHP2800D-2
Safety information
Getting Started . . .
12.
Before using, check the supply and extension cord for signs
of damage and aging. Do not use the product if the cord is
damaged or worn. DO NOT TOUCH THE CORD BEFORE
DISCONNECTING THE SUPPLY.
13.
Do not use the product if the extension cord is damaged
or worn.
14.
Have your product serviced by a qualied repair person
using only identical replacement parts. This will ensure that
the safety of the product is maintained.
15.
If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualied persons
in order to avoid a hazard.
Vibration and noise reduction
To reduce the impact of noise and vibration emission,
limit the time of operation, use lowvibration and low-
noise operating modes as well as wear personal protective
equipment.
Take the following points into account to minimise the
vibration and noise exposure risks:
1. Only use the product as intended by its design and these
instructions.
2.
Ensure that the product is in good condition and well
maintained.
3.
Use correct cutting attachments for the product and ensure
they are in good condition.
4. Keep tight grip on the handles/grip surface.
5.
Maintain this product in accordance with these instructions
and keep it well lubricated (where appropriate).
6. Plan your work schedule to spread any high vibration tool
use across a longer period of time.
9
MSHP2800D-2 Safety information
Getting Started . . .
Emergency
Familiarise yourself with the use of this product by means
of this instruction manual.Memorise the safety directions
and follow them to the letter. This will help to prevent risks
and hazards.
1.
Always be alert when using this product, so that you can
recognise and handle risks early. Fast intervention can
prevent serious injury and damage to property.
2.
Switch off and disconnect from the power supply if there
are malfunctions. Have the product checked by a qualied
professional and repaired, if necessary, before you operate
it again.
Residual risks
Even if you are operating this product in accordance
with all the safety requirements, potential risks of injury
and damage remain. The following dangers can arise in
connection with the structure and design of this product:
1.
Injuries and damage to property due to broken cutting
attachments or the sudden impact of hidden objects during
use.
2.
Injuries and damage to property to due to thrown and fallen
objects.
3.
Physical injuries caused by whipped material to be shredded.
WARNING! This product produces an electromagnetic
field during operation! This field may under some
circumstances interfere with active or passive medical
implants! To reduce the risk of serious or fatal injury, we
recommend persons with medical implants to consult
their doctor and the medical implant manufacturer before
operating this product!
10
MSHP2800D-2
Safety information
Getting Started . . .
Symbols explanation
On the product, the rating label and within these instructions you will nd among others
the following symbols and abbreviations. Familiarise yourself with them to reduce hazards
like personal injuries and damage to property.
V~ Volt, (alternating voltage)
Hz Hertz
kW Kilowatt
AAmpere
/min or min-1Per minute
mm Millimetre
LLitre
kg Kilogram
dB(A) Decibel (A-rated)
m/s2Metres per second squared
IPX4 Protection against splashing water, but no protection against dust.
Lock / to tighten or secure.
Unlock / to loosen.
Note/Remark
Caution/Warning.
Read the instruction manual.
Wear hearing protection.
Wear eye protection.
Table des matières
Autres manuels Mac allister destructeur de papier
Manuels destructeur de papier populaires d'autres marques
Swingline
Swingline STACK-AND-SHRED200X&200XL 60X Mode d’emploi
GBC
GBC ShredMaster CC055 Manuel utilisateur
UNITED OFFICE
UNITED OFFICE UAV 190 A1 Manuel utilisateur
UNITED OFFICE
UNITED OFFICE UAV 190 A1 Manuel utilisateur
Rexel
Rexel Optimum AutoFeed+ 45X Manuel utilisateur
Martin Yale
Martin Yale 227284S1 Manuel utilisateur
