M2SYNTH BP VCF 113 Manuel utilisateur

BP VCF 113 V1c 1

BP VCF 113

Kit Assembly Instructions

BP VCF 113 V1c 2

Features

1 Volt / Octave cut-off frequency CV)

Cut-off modulation input with potentiometer attenuator (FM)

Resonance potentiometer control with an external CV resonance input

Self-oscillates with high resonance settings.

Kit Contents

Description

Reference

MOTM

Qty

Notes

Components Kit

7216-213-1

See BOM

Accessories Pack including:

7216-213-2

Pot Sticky Pads

7210-188

10mm M4 Spacers

7210-186

M4 x 14 Cap Head Screws

7210-187

M3 x 8mm Stainless Panel Screws

7216-151

14-Pin IC Socket

7212-332

18-Pin IC Socket

7212-334

Power Lead

7216-164

MU Voltage Adapter

MOTM Front Panel

7216-513

MOTM Back Panel

7216-803

1U4P6S

MU Front and Back Panel

7219-513

Main PCB

7216-013

Jack Socket PCB

7215-723

Jack Sockets

7216-606

Pack of 6

B100k Pots Long Shaft Angled

7216-704

Pack of 4

B100k Pots Short Shaft Angled

7216-734

Pack of 4

KM20B Knobs

7212-104

Pack of 4

MU Knobs

7219-104

Pack of 4

General Assembly Guidance

Booklet

BOM

S-7216-013-c

Circuit Schematic

S-7216-013-c

PCB Layout

S-7216-013-c

BP VCF 113 V1c 3

Assembly Instructions

The Band Pass VCF module has no particular requirements not already covered in the

‘General Guidance on a M²Synth Module Assembly’ booklet included with this kit.

Calibration

1. Power up module and allow to ‘warm up’ for 10 minutes

2. Connect a 440Hz sine wave @ 10V Pk-Pk to Signal input 1. Resonance to 0%, Signal 1

Level to 100%.

3. Adjust cut-off to give maximum amplitude output using an oscilloscope.

4. Adjust Pr1 to give a 10V Pk-Pk output.

5. Remove the sine wave signal from input 1. Adjust resonance until self-oscillation

occurs at approximate 10V pk-pk. Connect a frequency meter to the output.

6. Adjust Cut-off to give 100Hz

7. Apply a CV of 4V to the COF CV in 1 input

8. Use Pr2 to calibrate at 1.6kHz (see note below)

9. Repeat from step 5 until 4V gives 1.6kHz

Note: If the frequency is flat (<1.6kHz), use Pr2 and make the frequency lower (flatter), if

above target frequency, use the trimmer to make the frequency even higher, this can be

counter-intuitive. You will soon get the feel of how much to increase or decrease the

frequency by.

Specification

Supply voltage +/-12Vdc

Supply current +13mA / -16mA

Waveform levels +/-5V

Frequency range: 7Hz to >5.5kHz without any CV applied

Main PCB dimensions 43.5x130mm

Need tech support, post questions on our forum hosted by modwiggler.com

Autres manuels M2SYNTH Équipement d'enregistrement

M2SYNTH

M2SYNTH Voice 108 Manuel utilisateur

M2SYNTH

M2SYNTH VC ADSR 121 Manuel utilisateur

M2SYNTH

M2SYNTH HP VCF 111 Manuel utilisateur

M2SYNTH

M2SYNTH SV VCF 112 Manuel utilisateur

M2SYNTH

M2SYNTH 191 Manuel utilisateur

M2SYNTH

M2SYNTH VCLFO 105 Manuel utilisateur

M2SYNTH

M2SYNTH Ring Modulator 151 Manuel utilisateur

M2SYNTH

M2SYNTH AP VCF 115 Manuel utilisateur

M2SYNTH

M2SYNTH BR VCF 114 Manuel utilisateur

Manuels Équipement d'enregistrement populaires d'autres marques

KV2 Audio

KV2 Audio 500 Series Manuel utilisateur

Robotics Technologies

Robotics Technologies microBus-Cam II Manuel utilisateur

Seca

Seca 460 Manuel utilisateur

Cognex

Cognex MVS-8000 Series Manuel utilisateur

Mect

Mect MPNC006 Series Manuel utilisateur

Bad Caf

Bad Caf THE LEASH Manuel utilisateur

Strymon

Strymon NIGHTSKY Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric 16CH DIGITAL RECORDER DX-TL5000U Manuel utilisateur

Tews Technologies

Tews Technologies TPMC465 Manuel utilisateur

Honeywell

Honeywell Excel 50 Manuel utilisateur

SeaLevel

SeaLevel COMM+8.LPCI Manuel utilisateur

Arturia

Arturia AUDIOFUSE STUDIO Manuel utilisateur

Rukra

Rukra RK-1240 Manuel utilisateur

Samson

Samson SCOM Manuel utilisateur

Dynacord

Dynacord DPS260 Manuel utilisateur

Nice

Nice Core Manuel utilisateur

Pyle Pro

Pyle Pro PSS8 Manuel utilisateur

RF-System

RF-System TinyGate Manuel d'utilisation et d'entretien