M2 Antenna Systems 167XP22 Manuel utilisateur

M2 Antenna Systems, Inc. 4402 N. Selland Ave. Fresno, CA 93722

Tel: (559) 432-8873 Fax: (559) 432-3059 Web: www.m2inc.com

Rev.00

Model .........................................167XP22

Frequency Range.......................163 To 175 MHz

*Gain ..........................................14.21 dBi

Front to back ..............................18 dB Typical

Feed type ...................................“T” Match

Feed Impedance. .......................50 Ohms Unbalanced

Maximum VSWR........................1.5:1 Typical

Input Connector..........................“N” Female

Power Handling ..........................1.5 kW

Boom Length / Dia......................217” / 1”- 3/4”

Maximum Element Length..........37”

Turning Radius: ..........................Call

Stacking Distance.......................Call

Mast Size....................................1-1/2” to 2” Nom.

Wind area / Survival ...................1.0 Sq. Ft. / 100 MPH

Weight / Ship Wt.........................8 Lbs. / 10 Lbs.

M2 Antenna Systems, Inc.

Model No: 167XP22

SPECIFICATIONS:

*Subtract 2.14 from dBi for dBd

FEATURES:

The 167XP22 is high performance cross polarized antenna with a remarkably clean pattern. The pattern is important in

order to match the antenna’s noise temperature with modern low noise preamps. This antenna is ideal for satellite work

but is also excellent for terrestrial uses.

The CNC machined driven element module is O-ring sealed and weather tight for low maintenance and long-term peak

performance. Internal connections are encapsulated in a space-age silicone gel that seals out moisture and improves

power handling. The 3/16” 6061-T6 rod elements are centered to minimize interaction and maintain good ellipticity.

Insulators are UV stabilized and locked in place with stainless keepers. Rugged construction, uncompromising

performance for the boom length.

167XP22 ASSEMBLY MANUAL

TOOLS REQUIRED FOR ASSEMBLY: 1/2”, 7/16” and 11/32” spin-tights, end wrenches or sockets, pliers, Philip

head screw driver and measuring tape.

ASSEMBLING THE BOOM

1. Slip the 1-1/4” into the rear 1-1/2” section, align the holes and secure using (2) 8-32 x 2” screws. Add the 8-32

locknuts. Slip the 1” x 60” section into the 1-1/4” section. Align the holes and secure using (2) 8-32 x 1-1/2” screws

and locknuts. Finally add the 3/4” diameter boom tip and secure using (2) 8-32 x 1-1/4” screws and locknuts.

Tighten all hardware securely.

2. Set the boom up on bucks at waist level in preparation of element installation. It might be handy to install the large

6” x 8” x 3/16” boom to mast plate at this point as it can be “C” clamped to a bench to hold the boom steady for the

following steps. Install the two 1/4” eye bolts. One eyebolt goes in the hole just in front of the rear reflector. The

other attaches near the front of the 1” section.

INSTALLING THE ELEMENTS (NOTE: Deform the button insulators slightly with pliers to help hold the

elements in place during assembly.

1. Separate the 3/16” rod elements by length into two sets, “H” and “V”. NOTE: THE LENGTH OF THE THIRD

DIRECTOR DIFFER FOR THE HORIZONTAL TO VERTICAL SET. Install the “H” element set along the boom

by length and spacing as shown the DIMENSION SHEET. Start with the REFLECTOR (longest) element.

Balance it on your finger to find rough center and push on a black button insulator to about 3/4” off center. Push

the element through the holes and install the second button, pushing it up into boom. DO NOT BOTHER

CENTERING the element at this time and DO NOT INSTALL the stainless steel SHAFT RETAINERS yet. It is

easier to do after all the horizontal elements are installed in the boom.

167XP22 DIMENSION SHEET

167XP22

167XP22 ASSEMBLY MANUAL

2. Install the 3/16” DRIVEN ELEMENT ROD as you did the reflector and then the DIRECTOR ELEMENTS.

3. Now accurately center the elements using a tape measure. EQUALIZE the amount of rod sticking out on each

side of the boom within 1/16” or better. Once you have all the elements centered, sight down the element tips from

the rear comparing each side. Look for any obvious discrepancies and correct if found.

4. Begin installing the stainless SHAFT RETAINERS. Use thumb index finger to hold a retainer over end of the 3/8”

x 3” push tube (keeper dished into tube). Hold the element firmly and start the retainer onto the rod by applying

pressure with the push tube. Push the retainer until up tight against the button insulator (locking pliers, clamped up

against opposite button insulator will help maintain center reference and keep you from pushing the tube off center.

Alternately, grab the opposite side of the element near the boom and pull it hard sideways to the boom to preload

and increase the friction of the element on the button insulators while pushing the retainer. Do all the retainers on

one side first, DOUBLE CHECK CENTERING and then do the other side. Continue installing retainers until all

HORIZONTAL elements are locked in place.

5. Mount the HORIZONTAL DRIVEN ELEMENT BLOCK / 1/4” ROD ASSEMBLY to the TOP of the boom using a

8-32 x 1-3/4” screw. Orient the block with the two balun connectors facing forward, “N” connector to the rear.

6. Install the 8-32 x 1/4” set screws (internal Allen head - tool supplied) into the SHORTING BARS. Slide the bars

onto the element rods and Position the Shorting Bars per the DIMENSION SHEET. Align the rods parallel and

the bars with each other and tighten the set screws moderately at this time to keep the bars in place. Final tightening

should be done after each antenna has been checked out electrically with an antenna analyzer or SWR bridge.

ASSEMBLING VERTICAL ELEMENTS

7. Repeat steps #1 through #6 for the Vertical elements, using the Dimension Sheet as your guide to lengths and

spacing. Note the vertical driven element block HAS A RIGHT ANGLE “N’ CONNECTOR and should be mounted on

the RIGHT side of the boom when the rear driven block is up (LOOKING FORM THE REAR). The two connectors

for the balun face the rear.

COMPLETING ANTENNA

1. Install the seal nuts on each female balun connector with the black neoprene seal out. Then install a balun to

each driven element block connector. Form the balun coax away from the block in a single loop. Form closely to the

boom and secure near the loop end with a nylon tie. Depending on the model, a balun may loop around an element

in the opposite polarity. This is normal. Tighten the connectors gently with a 7/16” end wrench and then run the seal

nuts up against the face of each male cable connector. Gently tighten about 3/4 turn beyond finger tight with a 1/2”

end wrench.

OVERHEAD GUY SUPPORT ASSEMBLY:

1. Mount the small 3” x 4” plate where the second boom section just starts. Use 1-1/2” U-bolts, nuts and

lockwashers. Add the two 1” U-bolts loosely and then insert the fiberglass mast section with the large end into the

U-bolts. Align the top hole with the boom and tighten the nuts on the 1” U-bolts.

2. Tie one end of the 5/32 dacron guy rope to the front eyebolt. Thread the other end through the fiberglass mast top

hole and back to the rear of the boom. Open up the 1/4” turnbuckle until just one thread shows on each end inside

the body. Hook the turnbuckle into the rear eyebolt and attach the Dacron rope securely. Adjust the turnbuckle until

the boom is straight.

NOTE: The 167XP22 is a cross polarized antenna that creates fields in both H and V planes. By combining the

HORIZONTAL AND THE VERTICAL elements through equal lengths of 50 Ohm feed line and into an M2 2 port

power divider, RIGHT HAND CIRCULAR POLARITY is created. By making one of the feed lines longer by 1/2

wavelength, LEFT HAND CIRCULAR POLARITY is created. LEFT HAND CIRCULAR can also be done at the time

of assembly by mounting the REAR DRIVEN ELEMENT on the other side of the boom. Always mount this antenna

at the rear as shown or on a nonconductive support mas and bring the feedlines off the rear.

Carefully Manufactured By

M2 Antenna Systems, Inc.

4402 N. Selland Ave.

Fresno, CA 93722

(559) 432-8873 Fax (559) 432-3059

www.m2inc.com email: [email protected]

167XP22 PARTS LIST

DESCRIPTION QTY.

BOOM SECTION #1, 1-1/2” X .058 X 60” SOE....................1

BOOM SECTION (REAR), 2” X .058 X 30” ..........................1 *OPTIONAL*

BOOM SECTION #2, 1-1/4” X .058 X 60” SOE....................1

BOOM SECTION #3, 1” X .058 X 40” ..................................1

BOOM SECTION #4, 3/4” X .049 X 46” ...............................1

ELEMENTS, 3/16” ROD (SEE DIMENSION SHEET) ..........22

DRIVEN ELEMENT ASSEMBLY..........................................2

BALUN, RG-6 (1/2 WAVE) ...................................................2

MAST ASSEMBLY, 3/8” X 18” ROD FIBERGLASS.............1

BOOM TO MAST PLATE, .125” X 3” X 4”............................1

BOOM TO 4” SQUARE SUPPORT BOOM..........................1

GUY CORD, DACRON 5/32 X 180” .....................................1

COUNTERWEIGHT, 3” X 7” ROUND STEEL (7 LB) ...........1 *OPTIONAL*

ASSEMBLY MANUAL ..........................................................1

IN HARDWARE BAG #1: .....................................................

U-BOLT AND CRADLE, 1-1/2”.............................................4

U-BOLT (SQUARE), 4”.........................................................2

IN HARDWARE BAG #2: .....................................................

TURNBUCKLE, 1/4” HOOK AND EYE.................................1

EYEBOLTS, 1/4” X 2” SS .....................................................2

U-BOLT, 3/4” ........................................................................2

NUT, 1/4-20 SS ....................................................................4

LOCKWASHER, 1/4” SPLIT RING SS .................................4

SHORTING BAR ..................................................................4

BUTTON INSULATORS, 3/16”.............................................44

SHAFT RETAINER, 3/16” ....................................................44

EYEBOLT, 1/4” SHORT .......................................................2

NUT, 3/8-16 SS ....................................................................4

LOCKWASHER, 3/8 SPLIT RING SS ..................................4

NUT, 5/16-18 SS ..................................................................8

LOCKWASHER, 5/16 SPLIT RING SS ................................8

SET SCREW, 1/4-20 X 1/4” SS............................................2

SCREW, 8-32 X 1-3/4” SS ...................................................2

SCREW, 8-32 X 1-1/2” SS ...................................................2

SCREW, 8-32 X 1-1/4” SS ...................................................2

SET SCREW, 8-32 X 1/4” SS...............................................8

LOCKNUT, 8-32 SS .............................................................6

CABLE TIE, NYLON.............................................................3

ALLEN HEAD WRENCH, 5/64”............................................1

NUTSEAL.............................................................................4

PUSH TUBE, 3/8” X 3” .........................................................1

167XP22 PARTS & HARDWARE

Table des matières

Autres manuels M2 Antenna Systems Antenne

M2 Antenna Systems

M2 Antenna Systems 432-15WL Guide de démarrage rapide

M2 Antenna Systems

M2 Antenna Systems FG2227-21X4CP Manuel utilisateur

M2 Antenna Systems

M2 Antenna Systems 10M4DX Manuel utilisateur

M2 Antenna Systems

M2 Antenna Systems 420-50-11 Manuel utilisateur

M2 Antenna Systems

M2 Antenna Systems 6-30LP11 Manuel utilisateur

M2 Antenna Systems

M2 Antenna Systems 915XBISP Manuel utilisateur

M2 Antenna Systems

M2 Antenna Systems 222XP30 Manuel utilisateur

M2 Antenna Systems

M2 Antenna Systems 40M3L Manuel utilisateur

M2 Antenna Systems

M2 Antenna Systems 295XP6 Manuel utilisateur

M2 Antenna Systems

M2 Antenna Systems 140CP14M Manuel utilisateur

M2 Antenna Systems

M2 Antenna Systems Relay/Preamp Housing with MAP65 Manuel utilisateur

M2 Antenna Systems

M2 Antenna Systems 418CP30 Manuel utilisateur

M2 Antenna Systems

M2 Antenna Systems 300XP12 Manuel utilisateur

M2 Antenna Systems

M2 Antenna Systems 80M1L Manuel utilisateur

M2 Antenna Systems

M2 Antenna Systems 436CP30 Manuel utilisateur

M2 Antenna Systems

M2 Antenna Systems 41-3BB Manuel utilisateur

M2 Antenna Systems

M2 Antenna Systems 436CP42UG Manuel utilisateur

M2 Antenna Systems

M2 Antenna Systems 2MCP8A Manuel utilisateur

M2 Antenna Systems

M2 Antenna Systems 450-800-12 Manuel utilisateur

M2 Antenna Systems

M2 Antenna Systems 75-5AS Manuel utilisateur

M2 Antenna Systems

M2 Antenna Systems DCN100-500 Manuel utilisateur

M2 Antenna Systems

M2 Antenna Systems 20M6-125 Manuel utilisateur

M2 Antenna Systems

M2 Antenna Systems EB-144/RK2M Manuel utilisateur

M2 Antenna Systems

M2 Antenna Systems 400CP30A Manuel utilisateur

Manuels Antenne populaires d'autres marques

Alfa Network

Alfa Network APA-L01 Manuel utilisateur

Naval

Naval PR-422CA Manuel utilisateur

Feig Electronic

Feig Electronic ID ISC.ANTH200/200 Series Manuel utilisateur

TERK Technologies

TERK Technologies TV44 Manuel utilisateur

Directive Systems & Engineering

Directive Systems & Engineering DSE2324LYRMK Manuel utilisateur

HP J8999A Manuel utilisateur

MobilSat

MobilSat MSP-S Manuel utilisateur

Steren

Steren ANT-UHF 13 Manuel utilisateur

Novatel

Novatel 600-G Manuel d'utilisation

Radio Shack

Radio Shack Amplified VHF/UHF/FM Indoor Antenna Manuel utilisateur

TRENDnet

TRENDnet TEW-AO12O Manuel utilisateur

Radio Shack

Radio Shack 15-1837 Manuel utilisateur

CommScope

CommScope CMAX-OMFX-43M-I53 Manuel utilisateur

Ramsey Electronics

Ramsey Electronics DAP25 Manuel utilisateur

COBHAM

COBHAM SAILOR 800 VSAT Manuel d'utilisation et d'entretien

Trango Systems

Trango Systems AD900-9 Manuel utilisateur

Steren

Steren ANT-100 Manuel utilisateur

Proxim

Proxim 5054-PA-23 Manuel utilisateur