M-TI FREEDOM MICRO 2 HS Manuel utilisateur

FREEDOM MICRO®II HS MANUAL

Product Manual for

FREEDOM MICRO®II HS

DO NOT REMOVE FROM STORE

Contents

1. Components And Accessories 2

2. Baseplate Options 3

3. Speedplate™ Merchandising 5

4. Speedbracket™ Merchandising 8

5. SmartCable™ Merchandising 10

6. RFID Commands 11

7. RFID MTI Connect®Pairing 12

8. LED Status Indicators 13

9. Dimensions 15

10. FCC and ISED Statement 18

For additional support, please reach out to our

Contact Center at 800-426-6844

CONTENTS

WARNING: MTI products contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.

Proposition 65, California Health & Safety Code Section 25249.6 et seq. Visit oehha.ca.gov for more information.

-CONTROLLED DOCUMENT- 063-00341 A-0 Status: Approved ECO-111980

ECO-111980

FREEDOM MICRO®II HS MANUAL

COMPONENTS AND ACCESSORIES

SpeedBracket™

Slot MountingThrough Hole MountingVHB Mounting

SpeedPlate™ OptionsPower Supply Freedom Micro®II Tool

Mounting Options

Freedom Micro®II RiserFreedom Micro®II Puck

Phones

Only use 5.9V 3.5A MTI Power Supply,

not exceed PS 2. Other spec may cause

damage.

Tablets

-CONTROLLED DOCUMENT- 063-00341 A-0 Status: Approved ECO-111980

ECO-111980

FREEDOM MICRO®II HS MANUAL

Route the cable as desired and attach the baseplate with

the included screws.

Routing out

the back

Routing out the bottom

Peel the red lm from the adhesive.

Place Micro position in desired location. Press down on

the base plate for 10 seconds for full adhesive contact.

Allow 24 hours for full adhesion.

Use the individual power supply and plug it into the

nearest outlet. The socket-outlet shall be installed near

the equipment and shall be easily accessible.

BASEPLATE OPTIONS - ADHESIVE

1 2 3

Do not cut power cable.

ADHESIVE POSITION REMOVAL

-CONTROLLED DOCUMENT- 063-00341 A-0 Status: Approved ECO-111980

ECO-111980

MOUNTING SLOT & THROUGH-HOLE ADAPTERS

Slot adapter shown. Through-hole adapter attaches in the same way.

BASEPLATE OPTIONS - SLOT & THROUGH-HOLE ADAPTERS

Place the power cable into the slot on the bottom

plate, then slide it up over the slot adapter post.

Insert the Freedom Micro®II position into the slot or

hole.

Secure the Freedom Micro®II position with the knob. Use the individual power supply and plug it into

the nearest outlet. Use an outlet installed near the

equipment that is easily accessible.

-CONTROLLED DOCUMENT- 063-00341 A-0 Status: Approved ECO-111980

ECO-111980

FREEDOM MICRO®II HS MANUAL

SPEEDPLATE™ MERCHANDISING

Peel red backing off of the adhesive on the

SpeedPlate™.

Clean the device with an alcohol wipe.

Apply the SpeedPlate™ to the phone, with the cable

retainer towards the charge port of the phone. Use the

SpeedPlate™ cable retainer as alignment reference.

Place the device onto the puck and rotate the device

clockwise on the puck until it locks into place.

-CONTROLLED DOCUMENT- 063-00341 A-0 Status: Approved ECO-111980

ECO-111980

FREEDOM MICRO®II HS MANUAL

4Remove the SpeedPlate™ from the Freedom Micro®II

Puck, then release and remove the Freedom Micro®II

tool.

With the Freedom Micro®II tool held in the twisted

position, rotate the SpeedPlate™ counterclockwise.

Twist the Freedom Micro®II tool clockwise 45 degrees

and hold it in place.

Insert the crescent end of the Freedom Micro®II tool

into the opening to the right of the LED.

REMOVING SPEEDPLATE™ FROM PUCK

-CONTROLLED DOCUMENT- 063-00341 A-0 Status: Approved ECO-111980

ECO-111980

FREEDOM MICRO®II HS MANUAL

REMOVING PUCK FROM TETHER

REMOVING SPEEDPLATE™ FROM DEVICE

Once the puck is loose, rotate the puck 45 degrees

counterclockwise in relation to the tether. Lift the puck

off of tether connection.

Lift puck out of riser, insert the crescent end of the

Freedom Micro II tool into the opening below the

charge port on the puck. Twist the Freedom Micro II

tool counterclockwise to unlock the puck from the

tether.

Place the SpeedPlate™ removal tool onto the

SpeedPlate™, aligning the holes on the tool with the

rotation locks.

Rotate the tool clockwise.

Roll any remaining adhesive off of the device.

-CONTROLLED DOCUMENT- 063-00341 A-0 Status: Approved ECO-111980

ECO-111980

FREEDOM MICRO®II HS MANUAL

SPEEDBRACKET™ MERCHANDISING

Loosen the center screw on the universal bracket to

loosen the bracket arms.

Place the phone into the universal bracket.

Extend the bracket arms as far as needed. The bracket

arms move simultaneously in pairs (top & bottom, and

left & right).

Adjust the universal bracket to t the device snugly.

Open the top and bottom bracket arms,

then the side arms, in that order.

-CONTROLLED DOCUMENT- 063-00341 A-0 Status: Approved ECO-111980

ECO-111980

FREEDOM MICRO®II HS MANUAL

7 8

SPEEDBRACKET™ MERCHANDISING

Tighten the center screw on the SpeedBracket™ to

secure the bracket arms in place around the device.

After tightening screw, wiggle the arms to ensure they

have fully engaged the lock teeth, then re-check screw

for tightness.

Place device back onto puck.

Rotate the device and bracket clockwise on the puck

until it locks into place.

*click*

-CONTROLLED DOCUMENT- 063-00341 A-0 Status: Approved ECO-111980

ECO-111980

FREEDOM MICRO®II HS MANUAL

REMOVING SMARTCABLE

ATTACHING SMARTCABLE™

Plug SmartCable into the charge port of the device.

Twist the device and bracket off of the position.

The loose cable can be clipped into SpeedBracket™

for easy storage.

Insert SmartCable into the charge port on the puck.

The hooks on cable should click when fully seated.

Insert the crescent end of the Freedom Micro II tool

into the opening to the right of the LED. Twist the

Freedom Micro II tool clockwise 45 degrees and hold

it in place.

Remove the SmartCable from the puck.

Phone should be turned ON, and unlocked

before inserting SmartCable™ while in

MTI Connect® mode.

-CONTROLLED DOCUMENT- 063-00341 A-0 Status: Approved ECO-111980

ECO-111980

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels M-TI Verrouillage

M-TI

M-TI Plunger Lock Manuel utilisateur

Manuels Verrouillage populaires d'autres marques

Magic

Magic 105 Manuel utilisateur

Gantner

Gantner GAT NET.Lock 7020 System Guide rapide

Wittkopp

Wittkopp Insys 7202 Manuel utilisateur

Dorma

Dorma Studio Classic Manuel utilisateur

Securam

Securam ECSL-601 Manuel utilisateur

Sudhaus

Sudhaus 3003 Manuel utilisateur

Safety 1st

Safety 1st 48517 Manuel utilisateur

Pado

Pado FDS-10 Manuel utilisateur

Esco

Esco systeQ Series Manuel utilisateur

COMPX

COMPX National D8951 Manuel utilisateur

secureo

secureo Key Box Manuel utilisateur

Stock Loks

Stock Loks C8713 Manuel utilisateur

COMPX

COMPX 1T-058 Manuel du propriétaire

Auslock

Auslock T11 Manuel utilisateur

ELCOM

ELCOM 7205 Manuel utilisateur

Stealth SAFES

Stealth SAFES ShadowVault Manuel utilisateur

Knox

Knox KeySecure 5 Manuel utilisateur

Kwikset

Kwikset 48334/01 Manuel utilisateur