M-system MD7G Manuel utilisateur

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-8065 Rev.2 P. 1 / 2

INSTRUCTION MANUAL

TERMINAL BLOCK FOR GROUNDING

(ultra-slim) MODEL MD7G

BEFORE USE ....

Thank you for choosing M-System. Before use, please check

contents of the package you received as outlined below.

If you have any problems or questions with the product,

please contact M-System’s Sales Ofﬁce or representatives.

■PACKAGE INCLUDES:

Terminal block.....................................................................(1)

■MODEL NO.

Conﬁrm Model No. marking on the product to be exactly

what you ordered.

■INSTRUCTION MANUAL

This manual describes necessary points of caution when

you use this product, including installation and connection.

POINTS OF CAUTION

■ENVIRONMENT

•Indoor use.

•When heavy dust or metal particles are present in the

air, install the unit inside proper housing with sufﬁcient

ventilation.

•Do not install the unit where it is subjected to continuous

vibration. Do not subject the unit to physical impact.

•Environmental temperature must be within -25 to +85°C

(-13 to +185°F) with relative humidity within 30 to 90%

RH in order to ensure adequate life span and operation.

•This unit needs a DIN rail as earth grounding bar. Ox-

ide coating of an aluminium rail may lower the electric

conductivity between this module and the ground. Use a

steel or copper rail.

COMPONENT IDENTIFICATION

Body

Spring Loader

DIN Rail Mounting

Adaptor (for grounding)

Connection

Diagram

(left side)

Model No.

Indication

INSTALLATION

Mount the unit on a DIN rail. Once installed, do not move

it to another DIN rail.

■MOUNTING THE UNIT ON A DIN RAIL

A)Hang the upper hook of the DIN rail mounting adaptor at

the rear side of unit, on the DIN rail.

B)Push in the lower in keeping pressing the unit to the DIN

rail.

C)DIN rails generally have slight individual variability in

size. If you ﬁnd it difﬁcult to push in the lower part, go

back to (A) and hang the upper part more deeply onto the

rail and try (B) again.

DIN Rail

■REMOVING THE UNIT

A)Push down the spring loader utilizing a minus screwdriv-

er.

B)Conﬁrm that it is pulled enough down and pull out the

lower part of the unit.

C)Detach the upper part from the DIN rail.

Spring Loader

MD7G

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax: +81(6)6659-8510 E-mail: info@m-system.co.jp

EM-8065 Rev.2 P. 2 / 2

TERMINAL CONNECTION

Connect the unit as in the diagram below.

Be sure to ground the DIN rail on which the unit is mounted.

This unit, designed to connect shield wires and cross wires of the protected devices to a DIN rail, is NOT used to ground the

DIN rail.

■EXTERNAL DIMENSIONS unit: mm (inch)

95 (3.74)

(.28)

98 (3.86) [1.5 (.06)]

8–M3 EURO

TERMINAL

DIN RAIL

(35 mm wide)

DIN RAIL

ADAPTOR

WIRE INSERTION ANGLE: approx. 20°

57 (2.24)

1.9 (.07)

■CONNECTION DIAGRAM

2 5

3 6

1 4

DIN RAIL ADAPTOR

(for grounding)

DIN RAIL

Grounding

DO NOT connect to unused terminals.

*1. Oxide coating of an aluminium rail may lower the electric conductivity

between this module and the ground. Use a steel or copper rail.

*2. Be sure to ground the DIN rail.

Recommended grounding resistance ≤100Ω

WIRING INSTRUCTIONS

■EURO TERMINAL

Torque: 0.3 N·m

Applicable wire size: 0.2 – 2.5 mm2

Stripped length: 8 mm

■CAUTION WHEN WIRING

Hold the module steady at the front when you

tighten/loosen screw terminals.

Autres manuels M-system Parafoudre

M-system

M-system MMAJ Manuel utilisateur

M-system

M-system MDK-LC Manuel utilisateur

M-system

M-system MDP-24T Manuel utilisateur

M-system

M-system MD73W Manuel utilisateur

M-system

M-system MD6 24 Series Manuel utilisateur

M-system

M-system MGA-100 Manuel utilisateur

M-system

M-system MDCAT-SPE Manuel utilisateur

M-system

M-system MD7PM Manuel utilisateur

M-system

M-system MDP-100 Manuel utilisateur

M-system

M-system MDP-100T Manuel utilisateur

M-system

M-system MDCAT 5E Manuel utilisateur

M-system

M-system MD7FB Manuel utilisateur

M-system

M-system MH-1201 Manuel utilisateur

M-system

M-system MAL-230x Manuel utilisateur

M-system

M-system MDP-SP Manuel utilisateur

M-system

M-system MDCAT-A Series Manuel utilisateur

M-system

M-system MDP-24-1 Manuel utilisateur

M-system

M-system MDP-LWA Manuel utilisateur

M-system

M-system MDP-RB Manuel utilisateur

M-system

M-system MDP-JS Manuel utilisateur

M-system

M-system MD7PA Manuel utilisateur

M-system

M-system MDPA-24 Manuel utilisateur

M-system

M-system MD7TC Manuel utilisateur

M-system

M-system MDK-24 Manuel utilisateur

Manuels Parafoudre populaires d'autres marques

ELAC

ELAC ProteK PR91-W Manuel utilisateur

Tsubaki

Tsubaki TSM4000M1 Manuel utilisateur

QVS

QVS PP134C Manuel utilisateur

CyberPower

CyberPower CSP604T Manuel utilisateur

Davis Instruments

Davis Instruments Radio Surge Protector Manuel utilisateur

CyberPower

CyberPower CSP706T Manuel utilisateur

CyberPower

CyberPower B300WRC1 Manuel utilisateur

Leviton

Leviton 51120-3R Manuel utilisateur

Panamax

Panamax MAX 5400-EX Manuel utilisateur

CyberPower

CyberPower B1006T Manuel utilisateur

OBO Bettermann

OBO Bettermann ÜSM-20-230I1PE65 Manuel utilisateur

Minuteman

Minuteman MMS7120RCT Manuel utilisateur

Leviton

Leviton 52412-DS3 Manuel utilisateur

Savio

Savio LZ-07 Manuel utilisateur

Siemens

Siemens HNM3M120 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric LITOL LTM-125RF Manuel utilisateur

Intermatic

Intermatic PS3000 Manuel utilisateur

ASCO POWER TECHNOLOGIES

ASCO POWER TECHNOLOGIES 360 Manuel utilisateur